HP LaserJet 4250 User Manual

							Font selection
FunctionCommandOptions (#)
Symbol setsEc(#8U = HP Roman-8 Symbol Set
10U = IBM Layout (PC-8) (code
page 437) Default Symbol Set
12U = IBM Layout for Europe
(PC-850) (code page 850)
8M = Math-8
19U = Windows 3.1 Latin 1
9E = Windows 3.1 Latin 2
(commonly used in Eastern
Europe)
5T = Windows 3.1 Latin 5
(commonly used in Turkey)
579L = Wingdings Font
Primary spacingEc(s#P0 = Fixed
1 = Proportional
Primary pitchEc(s#H# = Characters/inch
Set pitch mode1Ec&k#S0 = 10
4 = 12 (elite)
2 = 16.5 - 16.7 (compressed)
Primary heightEc(s#V# = Points
Primary styleEc(s#S0 = Upright (solid)
1 = Italic
4 = Condensed
5 = Condensed italic
Primary stroke wt.Ec(s#B0 = Medium (book or text)
1 = Semi bold
3 = Bold
4 = Extra bold
TypefaceEc(s#TPrint a PCL 6 or PCL 5 font list
to view the command for each
internal font.
1The preferred method is to use the primary pitch command.
ENWW Understanding PCL 6 and PCL 5e printer command syntax  259
 
						

							260Appendix E Printer commands  ENWW
 
						

							F
Regulatory information
Introduction
This section contains the following regulatory information:
●
FCC regulations
●
Environmental Product Stewardship program
●
Declaration of conformity
●
Laser safety statement
●
Canadian DOC statement
●
Korean EMI statement
●
Finnish laser statement
ENWW Introduction261
 
						

							FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy. If this equipment is not
installed and used in accordance with the instructions, it may cause harmful interference to
radio communications. However, there is no guarantee  that interference will not occur in a
particular installation; the presence of interference can be determined by turning the
equipment off and on. If this equipment  does cause harmful interference to radio or
television communications, the user is encouraged to try to correct the interference by one or
more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase distance between equipment and receiver.
● Connect equipment to an outlet on a circuit  different from that to which the receiver is
located.
● Consult your dealer or an experienced radio/television technician.
NOTE
Any changes or modifications to the printer that  are not expressly approved by HP could void
the user’s authority to operate this equipment.
Use of a shielded interface cable is required to comply  with the Class B limits of Part 15 of
FCC rules.
262 Appendix F Regulatory information ENWW
 
						

							Environmental Product Stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally
sound manner. This product has been designed with several attributes to minimize impacts
on our environment.
Ozone production
This product generates no appreciable ozone gas (O3).
Energy consumption
Power usage drops significantly while in PowerSave mode, which saves natural resources
and saves money without affecting the high performance of this product. \
This product
qualifies for ENERGY STAR
® (Printers, Version 3.0), which is a voluntary program to
encourage the development of energy-efficient office products.
ENERGY STAR® is a U.S. registered service mark owned by the U.S. government. As an
ENERGY STAR partner, Hewlett-Packard Company has determined that this product meets
ENERGY STAR Guidelines for energy efficiency. For more information, see
http://www.energystar.gov .
Toner consumption
EconoMode uses significantly less toner, which might  extend the life of the print cartridge.
Paper use
This products automatic duplex feature (two-sided printing) and n-up printing (multiple
pages printed on one page) capabilities can reduce media usage and the resulting demands
on natural resources. (The automatic duplex feature is available only for models that include
a built-in duplexer. Manual duplexing is available for all models. See 
Printing on both sides
of paper (optional duplexer) .)
Plastics  
Plastic parts over 25 grams are marked according to international standards that enhance
the ability to identify plastics for recycling purposes at the end of the products life.
HP LaserJet printing supplies
In many countries/regions, this products printing supplies (for example, print cartridge and
fuser) can be returned to HP through the HP Printing Supplies Environme\
ntal Program. An
easy-to-use and free take back program is available in more than 30 countries/regions.
Multilingual program information and instructions are included in every new HP LaserJet
print cartridge and supplies package.
HP Printing Supplies Returns and Recycling Program Information
ENWW Environmental Product Stewardship program 263
 
						

							Since 1992, HP has offered HP LaserJet supplies return and recycling free of charge in 86%
of the world market where HP LaserJet supplies are sold. Postage-paid and pre-addressed
labels are included within the instruction guide in most HP LaserJet print cartridge boxes.
Labels and bulk boxes are also available through the Web site at  http://www.hp.com/recycle.
More than 10 million HP LaserJet print cartridges  were recycled globally in 2002 through the
HP Planet Partners supplies recycling program. This record number represents 26 million
pounds of print cartridge materials that were diverted from landfills. Worldwide, HP recycled
an average of 80% of the print cartridge by weight, consisting primarily of plastic and metals.
Recycled plastics and metals are used to make new products, such as HP products, plastic
trays, and spools. The remaining materials are disposed of in an environmentally
responsible manner.
● U.S. returns  For a more environmentally responsible return of used cartridges and
supplies, HP encourages the use of bulk returns. Simply bundle two or more cartridges
together and use the single, prepaid, preaddressed UPS label that is supplied in the
package. For more information in the U.S., call 1-800-340-2445 or visit the HP LaserJet
Supplies Web site at  http://www.hp.com/recycle .
● Non-U.S. returns  Non-U.S. customers should call the local HP Sales and Service Office
or visit the  http://www.hp.com/recycle  Web site for further information regarding
availability of the HP Supplies Returns and Recycling Program.
Paper
This product is capable of using recycled papers when the paper meets the guidelines
outlined in the  HP LaserJet Printer Family Print Media Guide . Go to http://www.hp.com/
support/ljpaperguide  to download this guide in .PDF format. This product is suitable for the
use of recycled media according to EN12281:2002.
Material restrictions   
This HP product does not contain added mercury.
This HP product may initially contain lead in  solder that might require special handling at end-
of-life. This product will eventually switch to lead-free construction in compliance with the
European Waste from Electrical and Electronic Equipment (WEEE) law.
This HP product contains a battery that might require special handling at end-of-life.
TypeLithium Carbon Monofluoride (BR1632), 3 Volt,
button-style battery, 1.5 grams
MaterialsMercury-free, Cadmium-free
LocationOn printed circuit board
User removableNo
For recycling information, you can contact  http://www.hp.com/recycle or contact your local
authorities or the Electronics Industry Alliance:  http://www.eiae.org.
Material safety data sheet
Material Safety Data Sheets (MSDS) for supplies that contain chemical substances (for
example, toner) can be obtained by contacting the HP Web site at  http://www.hp.com/go/
msds  or http://www.hp.com/hpinfo/community/environment/productinfo/safety .
264 Appendix F Regulatory information ENWW
 
						

							For more information
To obtain information about the following environmental topics, visit http://www.hp.com/go/
environment  or http://www.hp.com/hpinfo/community/environment/productinfo/safety .
● Product environmental profile sheet for this and many related HP products.
● HPs commitment to the environment
● HPs environmental management system
● HPs end-of-life product return and recycling program
● Material Safety Data Sheets (MSDS)
ENWW Environmental Product Stewardship program 265
 
						

							Declaration of conformity
Declaration of Conformity
according to ISO/IEC Guide 22 and EN 45014
Manufacturers Name:Hewlett-Packard Company
Manufacturers Address: 11311 Chinden Boulevard
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name: HP LaserJet 4250 and LaserJet 4350 printer
Regulatory Model Number
3): BOISB-0309-00
Including optional duplex accesssory (Q2439B), optional 500-sheet input tray
(Q2440B), optional 1500-Sheet Input Tray (Q2440B), and optional 500-sheet stapler/
stacker accessory (Q2443B)
Product Options: ALL
conforms to the following Product Specifications:
Safety: IEC 60950:1999 / EN60950: 2000 IEC 60825-1:1993 +A1 +A2 / EN 60825-1:1994  +A11 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC: CISPR 22:1997 / EN 55022:1998 Class B
1)
EN 61000-3-2:1995 + A14
EN 61000-3-3:1995 + A1
EN 55024:1998
FCC Title 47 CFR, Part 15 Class B
2) / ICES-003, Issue 4
GB9254-1998, GB17625.1-1998
Supplementary Information:
The product herewith complies with the requirements of the EMC  Directive 89/336/EEC and the Low Voltage Directive 73/23/EEC, an d carries
the CE-Marking accordingly.
1) The product was tested in a  typical configuration with Hewlett-Packard Personal Computer Systems.
2) This Device complies with Part 15 of the FCC Rules. Operation  is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any  interference received, including interference that may cause undesire d operation.
3) For regulatory purposes, this product is assigned a Regulatory model  number. This number should not be confused with the marketing
name or the product number(s).
Boise, Idaho , USAMarch 12, 2004
For regulatory topics only:
Australia Contact: Product Regulations Manager, Hewlett-Packard Australia Ltd., 31-41 Joseph Street Blackburn, Victoria 3130, Australia
European Contact: Your Local Hewlett-Packard Sales and Service  Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe, Herrenberger Strasse 140 , D-71034, Böblingen (FAX: +49-7031-14-3143)
USA Contact: Product Regulations Manager, Hewlett-Packard Company, PO Box 15, Mail Stop 160 Boise, ID 83707-0015,  (Phone:
208-396-6000)
266Appendix F Regulatory information ENWW
 
						

							Country-/region-specific safety statements
Laser safety statement
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug
Administration has implemented regulations for laser products manufactured since August 1,
1976. Compliance is mandatory for products marketed in the United States. The printer is
certified as a Class 1 laser product under the U.S. Department of Health and Human
Services (DHHS) Radiation Performance Standard according to the Radiation Control for
Health and Safety Act of 1968.
Since radiation emitted inside the printer is completely confined within protective housings
and external covers, the laser beam cannot escape during any phase of normal user
operation.
WARNING!
Using controls, making adjustments, or performing procedures other than those specified in
this user guide may result in exposure to hazardous radiation.
Canadian DOC statement
Complies with Canadian EMC Class B requirements.
«Conforme àla classe B des normes canadiennes de compatibilité électromagnétiques
(CEM).»
Japanese VCCI statement
Korean EMI statement
ENWW Country-/region-specific safety statements 267
 
						

							Finnish laser statement
LASERTURVALLISUUS
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
HP LaserJet 4250, 4250n, 4250tn, 4250dtn, 4250dtnsl, 4350, 4350n, 4350tn, 4350dtn, and
4350dtnsl -laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa
käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen ulkopuolelle.
Laitteen turvallisuusluokka on määritetty standardin EN60825-1 (1994) mukaisesti.
VAROITUS!
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla t\
avalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING!
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren
utsättas för osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet 4250, 4250n, 4250tn, 4250dtn, 4250dtnsl, 4350, 4350n, 4350tn, 4350dtn, and
4350dtnsl -kirjoittimen sisällä ei ole käyttäjän huollettavissa olevia kohteita.\
 Laitteen saa
avata ja huoltaa ainoastaan sen huoltamiseen koulutettu henkilö. Tällaiseksi
huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan puhdistusta tai
muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia, jotka
voidaan suorittaa ilman erikoistyökaluja.
VARO!
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömälle lasersäteilylle laitteen
ollessa toiminnassa. Älä katso säteeseen.
VARNING!
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för
osynlig laserstrålning. Betrakta ej strålen.
Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuks\
ista:
Aallonpituus 770-800 nm
Teho 5 mW
Luokan 3B laser
268 Appendix F Regulatory information ENWW