JVC Gz Ex310bu User Manual

							0After selecting a date, tap “NEXT”.
0 When “ALL” is tapped, Digest Playback will be performed for all the
dates.
0 Tap  L to exit the menu.
0 Tap  0029 to return to the previous screen.
7 Tap to select a scene for Digest Playback.
.
0Error message is displayed if no scene is found. Select another
scene, or tap “AUTO”.
8 Select the Digest Playback time
(Only when “AUTO” is selected in Step 7)
.
0The time display of Digest Playback varies according to the recording
time.
0 When it takes time (more than 2 seconds) for “DIGEST PLAYBACK”
to start after selecting Digest Playback time, a progress status will be
displayed.
0 The Digest Playback time is only a guide.
9 Digest Playback starts.
.
0Tap  001A to pause.
0 Tap  0038 to return to the index screen.
0 Tap “DIGEST L“ to return to the normal playback screen.
0 Operations During Video Playback
“Operation Buttons for Video Playback” ( A p. 64)
o
Types of Digest Playback
Select the types of Digest Playback from the following. When “AUTO” is
selected, playback is performed by shortening the video to the pre-set length of time.ItemDetailsAUTOPlayback is performed by shortening the video to the
pre-set length of time.
Depending on the recording time of the video,
playback time can be selected from: 1 minute, 3
minutes, 5 minutes, 10 minutes, 15 minutes, 30
minutes, 45 minutes and 60 minutes. All the recorded parts (recording time is less than 1 minute) are played
back.SMILING FACE
SCENEPlayback the scenes with detected smiles as a digest. Set “SMILE SHOT” in “RECORD SETTING” to ON.
“Capturing Smiles Automatically (SMILE SHOT)”
( A  p. 45)REGISTERED
FACE SCNPlayback the scenes mainly with a person whose face
is registered
“Registering Human Face Personal Authentication
Information” ( A p. 48)MARKED
SCENEStart a digest playback by piecing the scenes that are
marked during recording.Playback71 
						

							PLAYBACK PLAYLIST
Plays back the playlists that you have created.
0 The following is a screen of the model with the built-in memory.
1
Open the LCD monitor.
.
0Check if the recording mode is  0010.
0 If the mode is  0011 still image, tap  0011 on the recording screen to display
the mode switching screen.
Tap  0010 to switch the mode to video. (You can also use the  0010/0011  button
on this unit.)
2 Tap “
						

							PLAYBACK OTHER FILE
The management information of a video may be damaged if recording is not
performed correctly, such as turning off the power in the middle of recording.
You can perform the following operations to play back the videos with
defective management information.
0 The following is a screen of the model with the built-in memory.
1
Open the LCD monitor.
.
0Check if the recording mode is  0010.
0 If the mode is  0011 still image, tap  0011 on the recording screen to display
the mode switching screen.
Tap  0010 to switch the mode to video. (You can also use the  0010/0011  button
on this unit.)
2 Tap “
						

							Playing Back Still Images
You can select and play back the recorded still images from an index screen
(thumbnail display).
0 The following is a screen of the model with the built-in memory.1
Open the LCD monitor.
.
0Check if the recording mode is  0011.
0 If the mode is  0010 video, tap  0010 on the recording screen to display the
mode switching screen.
Tap  0011 to switch the mode to still image. (You can also use the  0010/0011
button on this unit.)
2 Tap “
						

							During Still Image Playback
.
DisplayDescriptionAVideo/Still Image
ModeSwitches between video and still image
modes.B0015Rotates to the left (rotates by -90° with each
tap)C0016Rotates to the right (rotates by 90° with each
tap)D001FReturns to the previous still image
0 You can perform the same operation with the
zoom lever.E0019  / 001AStarts/pauses slideshow
“Slideshow Playback” ( A p. 75)F001DAdvances to the next still image
0 You can perform the same operation with the
zoom lever.G
						

							Searching for a Specific Video/Still Image byDate
When there is a large number of recorded videos and still images, it is difficult
to look for the desired file from the index screen.
Use the search function to find the file you want.
You can search and play videos or still images according to recording dates.
0 The following is a screen of the model with the built-in memory.1
Tap “MENU”.
.
0Tap  0027/0028  to select the media for playback.
0 Searching can be performed in both the video and still image modes.
*The image shows the video mode.
2 Tap “PLAYBACK SETTING”.
.
3Tap “SEARCH DATE”.
.
4Tap a recording date, then tap “NEXT”.
.
0Tap again to cancel the selected date.
5 Tap on the file to start playback.
.
0You can select videos in the video mode and still images in the still
image mode.
0 Only the files recorded on the selected date are displayed.
0 Tap  L to stop searching and return to the index screen (thumbnail
display).
Deleting Files of a Selected Date ：Tap 
0005 on the index screen (thumbnail display) to delete unwanted files.
“Deleting Unwanted Files” ( A p. 80)Playback76 
						

							Connecting to and Viewing on TV
You can connect this unit to a TV for playback. The image quality on TV
varies with the type of TV and the connecting cable. Select the connector
that best suits your TV.
0 Refer also to the instruction manual of the TV in use.
“Connecting via the HDMI Mini Connector” ( A p. 77)
“Connecting via the AV Connector” ( A p. 79)
0 To display the date and time on TV, set both “DISPLAY DATE/TIME” and
“DISPLAY ON TV” to “ON”.
“ DISPLAY DATE/TIME ” ( A p. 234)
“ DISPLAY ON TV ” ( A p. 241)
Unnatural Displays on TVTroubleActionImages do not
appear on the TV
properly.0 Disconnect the cable and connect again.
0 Turn off and on this unit again.
0 Images may not appear properly when the
remaining battery power is low. Use an AC
adapter.Images are
projected vertically
on the TV.0 Set “VIDEO OUTPUT” in the “CONNECTION
SETTINGS” menu to “4:3”.
“ VIDEO OUTPUT ” ( A p. 241)Images are
projected
horizontally on the
TV.0 Adjust the TV's screen accordingly.The color of images
looks strange.0 Adjust the TV's screen accordingly.HDMI-CEC
functions do not
work properly, and
the TV does not
work in conjunction
with this unit.0 TVs may operate differently depending on the
specifications, even if they are HDMI-CEC
compliant. Therefore, the HDMI-CEC functions
of this unit cannot be guaranteed to operate in
combination with all the TVs. In such cases, set
“HDMI CONTROL” to “OFF”.
“ HDMI CONTROL ” ( A p. 241)The language on
the display
changed.0 It may occur when you connect this unit to a TV
with different language setting using an HDMI
mini cable.Caution : 
0 Do not remove the recording medium or perform any other operation (such
as turning off the power) while accessing files. Also, be sure to use the
provided AC adapter, as the data on the recording medium may be
corrupted if the battery becomes exhausted during operation. If the data on the recording medium becomes corrupted, format the recording
medium to use the medium again.
Connecting via the HDMI Mini Connector
If you are using an HDTV, you can play back in HD quality by connecting to the HDMI mini connector.
0 Use a High Speed HDMI mini cable as the HDMI mini cable when not using
the provided one.
0 Use a High Speed HDMI mini cable as the HDMI mini cable.
0 Refer also to the instruction manual of the TV in use.
0 The following is a screen of the model with the built-in memory.
1
Connect to a TV.
.
0Turn off the camcorder by pressing the  002C button for about 2 seconds.
2 Connect the AC adapter to this unit.
.
0The unit turns on automatically.
3 Press the external input button on the TV to switch to the input from this
unit via the connected connector.
.
4Play back a file.
.
“Playing Back Videos” ( A p. 64)
“Playing Back Still Images” ( A p. 74)
Playback77 
						

							Memo : 
0Change the settings in “HDMI OUTPUT” according to the connection.
“ HDMI OUTPUT ” ( A p. 241)
0 When connected to the TV via the HDMI mini cable, images and sounds
may not be output properly depending on the TV connected.
In such cases, perform the following operations.
1) Disconnect the HDMI mini cable and connect it again.
2) Turn off and on this unit again.
0 For questions about the TV or method of connection, contact your TV's
manufacturer.Operating in Conjunction with TV via HDMI
Connecting this unit to an HDMI-CEC enabled TV using the HDMI mini cable allows linked operations with the TV to be performed.
0 HDMI-CEC (Consumer Electronics Control) is an industry standard that
enables interoperability between HDMI-CEC compliant devices that are
connected via HDMI cables.
Memo : 
0 Not all HDMI control devices comply with the HDMI-CEC standard. The
HDMI control function of this unit will not work when connected to these
devices.
0 This unit is not guaranteed to operate with all HDMI-CEC enabled devices.
0 Depending on the specifications of each HDMI-CEC enabled device,
some functions may not work with this unit. (For details, refer to the
instruction manual of your TV.)
0 Unintended operations may occur with some connected devices. In these
cases, set “HDMI CONTROL” to “OFF”.
“ HDMI CONTROL ” ( A p. 241)
Preparations
0
Connect an HDMI mini cable between this unit and the TV.
“Connecting via the HDMI Mini Connector” ( A p. 77)
0 Turn on the TV and set the HDMI-CEC related setting to “ON”. (For details,
refer to the instruction manual of the TV.)
0 Set “HDMI CONTROL” in the CONNECTION SETTINGS menu to “ON”.
“ HDMI CONTROL ” ( A p. 241)
Operation Method 1
1 Turn on this unit.
2 Select the playback mode.
3 Connect the HDMI mini cable.
0 TV turns on automatically and switches to HDMI input mode when
this unit is turned on.
Operation Method 2
1 Turn off the TV.
0 This unit turns off automatically.Memo : 
0Depending on the TV connected, the display language of this unit will
automatically switch to the language that is selected for the TV when this
unit is turned on.
(This is applicable only if this unit supports the language selected for the
TV.) To use this unit with a language that differs from the display language of the TV, set “HDMI CONTROL” to “OFF”.
0 The display language of the TV will not switch automatically, even if the
display language of this unit is changed.
0 These functions may not work correctly when devices such as amplifier
and selector are connected. Set “HDMI CONTROL” to “OFF”.
0 If HDMI-CEC does not work properly, turn off and on this unit again.Playback78 
						

							Connecting via the AV Connector
To playback videos on TV, connect the provided AV cable (P/N
QAM1322-001) to the AV terminal of this unit.
0 Refer also to the instruction manual of the TV in use.
0 The following is a screen of the model with the built-in memory.
1
Connect to a TV.
.
0 Turn off the camcorder by pressing the  002C button for about 2 seconds.
2 Connect the AC adapter to this unit.
.
0The unit turns on automatically.
3 Press the external input button on the TV to switch to the input from this
unit via the connected connector.
.
4Play back a file.
.
“Playing Back Videos” ( A p. 64)
“Playing Back Still Images” ( A p. 74)
Memo : 
0
For questions about the TV or method of connection, contact your TV's
manufacturer.
0 AV cable (P/N: QAM1322-001)
Wiring specifications (for video/audio) of the 4-pole mini plug are described
in the following.
For purchasing, consult your nearest JVC service center.
.Playing Back a DVD or Blu-ray Disc Createdon this Unit
DVDs or Blu-ray discs created using the backup function on this unit can be played back on TV using an optional DVD writer (DVDs only) with playback
function (CU-VD50) or a normal DVD or Blu-ray disc player. DVDs can also
be played back on this unit by connecting the optional DVD writer with
playback function.
“Playing Back with a DVD Writer” ( A p. 105)
“Playing Back with a BD Writer (External Blu-ray Drive)” ( A p. 98)
0 For details on how to play back on a normal DVD or Blu-ray disc player,
refer to the instruction manual of the player.Playback DeviceDVD
(AVCHD format)Blu-ray DiscDVD writer connected to
this unitP-BD writer (external Blu-ray
drive) connected to this unitPPDVD player/
DVD RecorderP *-Blu-ray player/
Blu-ray RecorderP *PDVD writer with playback
function (CU-VD50)P-
*Only for AVCHD compatible devices
Caution : 
0 DVDs that are created in AVCHD format cannot be played back on DVD
players with standard quality. You may not be able to remove the disc from
the player.
Digest Playback on a Blu-ray or DVD Player
You can play back a few seconds from each scene of the recorded videos
in the created disc.
1 Load the created disc on a player.
2 Select “DIGEST PLAYBACK” on the TV.
0 The digest is played back continuously.
.
(The screen does not appear on this unit.)
Memo : 
0To normal playback/To index menu
1) Press the top menu button on the remote control of the player during
digest playback.
2) Select the desired item.
0 “DIGEST PLAYBACK” menu is not available when the disc is created
using the provided LoiLoFit for Everio software.
0 Digest Playback is not available when playing back by connecting this unit
to a DVD writer or external Blu-ray drive.Playback79 
						

							Deleting Unwanted Files
Delete unwanted videos and still images when the space in the recording
media is running out.
Doing so frees up more space in the recording media. “Deleting the Currently Displayed File” ( A p. 80)
“Deleting Selected Files” ( A p. 80)Memo : 
0
Deleted files cannot be restored.
0 When files in a playlist are deleted, the playlist changes.
0 Files that are protected cannot be deleted.
Release protection before deleting the file.
“Protecting Files” ( A p. 81)
0 Be sure to back up important files on a computer.
“Backing Up Files” ( A p. 116)
Deleting the Currently Displayed File
Deletes the currently displayed file.
Caution : 
0
Deleted files cannot be restored.
1
Tap  0005.
.
0While the video mode is shown in the image, the same operations
apply for the still image mode.
2 Tap “YES”.
.
0Tap  001F  / 001D  to select the previous or next file.
0 When no file remains, the screen returns to the index screen.
Deleting Selected Files
Deletes the selected files.
0 The following is a screen of the model with the built-in memory.
Caution : 
0Deleted files cannot be restored.
1
Open the LCD monitor.
.
0Tap  0010 or  0011 to select the video or still image mode.
0 Tap  0011 or  0010 on the recording screen to display the mode switching
screen.
Tap  0006 to switch to the video mode  0010.
Tap  0007 to switch to the still image mode  0011.
(You can also use the  0010/0011  button on this unit.)
2 Tap “