NEC Neax 2400 Ipx Office Data Specification

NDA-24298 CHAPTER 4
Page 647
Issue 1
ARTI : Assignment of Trunk Application Data
6 T309CONAssignment of Timer T309 for Layer 1 Failure
0 = Layer 1 Alarm with T309 is disabled 
1 = Layer 1 Alarm [Temporary] with T309 is enabled
2 = Layer 1 Alarm [Permanent] with T309 is enabled 
3=Not used
7LLCRSTCall Restriction by user rate in Low Layer Capability 
Information Element 
     0= No restriction
1-31= Call which includes this user rate value is 
restricted. 
Note:User rate value is based on ITU-T Q-931....

CHAPTER 4 NDA-24298
Page 648
Issue 1
ARTI : Assignment of Trunk Application Data
20 DVRSTCall restriction while Tie Line is backed up on ISDN. 
0= No restriction
1 = Speech call restriction (Speech. 3.1 kHz audio, 7 
kHz audio calls are restricted)
2 = Data call restriction (Unrestricted digital, restricted 
digital and Video data are restricted.) 
3 = Both Speech and Data calls are restricted. 
21 RSCTCall restricted by Temporary Route Information 
0 = No restriction 1 = Restriction
Note: This data is...

NDA-24298 CHAPTER 4
Page 649
Issue 1
ARTI : Assignment of Trunk Application Data
32 SRV (Australia only)
Additional Service Selection 
bit 0 = Advice of Charge (AOC) 
0 = Valid 1 = Invalid
bit 1= Malicious Call Trace (MCT)/Malicious Call Iden-
tification (MCID) 
0 = Valid 1 = Invalid
bit2-bit6 = Not used 
bit7 = For TON and/or NPI
0 = Invalid 1 = Valid 
Note:Input this data by a decimal. 
33 TONType of Number 
0 = Unknown
1 = International Number 
2 = National Number 
3 = Network Special Number
4 =...

CHAPTER 4 NDA-24298
Page 650
Issue 1
ARTI : Assignment of Trunk Application Data
37 ECCISTMRelease timer for E-CCIS Line 
0 = 3 minutes (Default setting)
1 = 15 Seconds
2 = 30 Seconds
3=1 minute
4=2 minutes
5=5 minutes
6 = 10 minutes
7 = 30 minutes
8 = 30 minutes
9 = 1 hour
10-13 = Not used
14 = Immediately after call completion
15 = Not released
38 ECCISOBOG Billing for E-CCIS Line
0 = Out of Service
1=In Service
39 ECCISIBIC Billing for E-CCIS Line 
0 = Out of Service
1=In Service
4 0 SPMETAccount...

NDA-24298 CHAPTER 4
Page 651
Issue 1
ARTI : Assignment of Trunk Application Data
49 ECCIS2E-CCIS System
0 = Out of Service
1 = Common Channel System
2=Not used
3=Not used
50 IPINT(Japan only)
Public PCS Protocol
0-5 = Not used
6 = IP Protocol (2B + D)
7 = Public PCS Protocol (2B + D)
8-15 = Not used
51 IPTRKIP Trunk
0 = Out of Service
1=In Service
52 CTCFCall Transfer/Forwarding Q.SIG
Supplementary Service
0 = Out of Service
1=In Service
53 RERTRerouting Function
0 = Out of Service
1=In Service
54...

CHAPTER 4 NDA-24298
Page 652
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
ARTIN: Assignment of Trunk Application Data for NDM
1. General
This command assigns and deletes trunk application data in Fusion Network. The data assigned by this
command is written in the Network Data Memory (NDM) of the Network Control Node (NCN), updating the
NDM at each Local Node (LN).
2. Precautions
1. This command can be used only when logging in to NCN (Network Control Node).
2. The data assigned by this...

NDA-24298 CHAPTER 4
Page 653
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
4. Data Sheet
CDNLOGICAL ROUTE NUMBER (1-899)
TRUNK DATA
1 RST Assignment of Restart 
0 = Restart Send per Individual Channel
1 = Not used  2 = Not used
3 = Restart not Send
2 HMT  When assigning this data, always enter zero (0). 0 0 0 0
3 TRCRST Call Restriction by Information transfer rate in 
Bearer Capability Information Element 
0 = No restriction
1 = Data call restriction (Unrestricted digital, Re-
stricted...

CHAPTER 4 NDA-24298
Page 654
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
7 LLCRST Call Restriction by user rate in Low Layer 
Capability Information Element 
0 = No restriction
1-31 = Call which includes this user rate value is 
restricted. 
Note
Note:User rate value is based on 
ITU-T Q-931. 
8 VCM  When assigning this data, always enter zero (0). 0 0 0 0
9 OVRT  When assigning this data, always enter zero (0). 0 0 0 0
10 POOL When assigning this data, always enter zero (0). 0 0 0 0
11...

NDA-24298 CHAPTER 4
Page 655
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
20 DVRST Call restriction while Tie Line is backed up on 
ISDN. 
0 = No restriction
1 = Speech call restriction (Speech. 3.1 kHz 
audio, 7 kHz audio calls are restricted)
2 = Data call restriction (Unrestricted digital, 
restricted digital and Video data are 
restricted.) 
3 = Both Speech and Data calls are restricted. 
21 RSCT Call restricted by Temporary Route Information 
0 = No restriction
 1 = Restriction...

CHAPTER 4 NDA-24298
Page 656
Issue 1
ARTIN : Assignment of Trunk Application Data for NDM
31 ANI Timing to demand ANI Information 
0 = There is no ANI demand at Incoming call
1 = After receiving 1st digit
2 = After receiving 2nd dig it 
3 = After receiving 3rd dig it 
4 = After receiving 4th digit 
5 = After receiving 5th digit
6 = After receiving 6th digit 
7 = After receiving 7th digit
32 SRV (Australia only)
Additional Service Selection 
bit 0 = Advice of Charge (AOC) 
0 = Valid   1 = Invalid
bit 1 =...