Panasonic Dmc Fx80 Operating Instructions Manual

							- 151 -
Others
Cautions for Use
Keep this unit as far away as possible from electromagnetic equipment (such as 
microwave ovens, TVs, video games etc.).
•
If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be 
disrupted by electromagnetic wave radiation.
•Do not use this unit near cell phones because doing so may result in noise adversely affecting 
the pictures and/or sound.
•Recorded data may be damaged, or pictures may be distorted, by strong magnetic fields 
created by speakers or large motors.
•Electromagnetic wave radiation generated by mi croprocessors may adversely affect this unit, 
disturbing the pictures and/or sound.
•If this unit is adversely affected by electromagnetic equipment and stops functioning properly, 
turn this unit off and remove the battery or disconnect AC adaptor (supplied). Then reinsert the 
battery or reconnect AC adaptor and turn this unit on.
Do not use this unit near radio transmitters or high-voltage lines.
•If you record near radio transmitters or high-v oltage lines, the recorded pictures and/or sound 
may be adversely affected.
Always use the supplied cords and cables.  If you use optional accessories, use the 
cords and the cables supplied with them.
Do not extend the cords or the cables.
Do not spray the camera with insecticides or volatile chemicals.
•
If the camera is sprayed with such chemicals, the body of the camera may be damaged and the 
surface finish may peel off.
•Do not keep rubber or plastic products in contact with the camera for a long period of time.
The speaker does not have magnetic shielding. Do not keep this speaker and 
magnetised cards (bank cards, commuter passes, etc.) close together.
Optimal use of the camera 
						

							Others
- 152 -
Before cleaning the camera, remove the battery or disconnect the power plug from 
the outlet. Then wipe the camera with a dry, soft cloth.
•
When the camera is soiled badly, it can be cleaned by wiping the dirt off with a wrung wet cloth, 
and then with a dry cloth.
•Do not use solvents such as benzine, thinner, alcohol, kitchen detergents, etc., to clean the 
camera, since it may deteriorate the external case or the coating may peel off.
•When using a chemical cloth, be sure to follow the accompanying instructions.
•Do not press the LCD monitor with excessive force. Uneven colours may appear on the LCD 
monitor and it may malfunction.
•If the camera is cold when you turn it on, the picture on the LCD monitor will be slightly darker 
than usual at first. However, the picture will return to normal brightness when the internal 
temperature of the camera increases.
•Do not press against the lens with excessive force.•Do not leave the camera with the lens facing the sun, as rays of light from the sun may cause it 
to malfunction. Also, be careful when placing the camera outside or near a window.
Cleaning
About the LCD monitor
Extremely high precision technology is em ployed to produce the LCD monitor screen. 
However, there may be some dark or bright  spots (red, blue, or green) on the screen. 
This is not a malfunction. The LCD monitor screen has more than 99.99% effective 
pixels with a mere 0.01% of the pixels inactive or always lit. The spots will not be 
recorded on pictures on the built-in memory or a card.
About the Lens 
						

							- 153 -
Others
The battery is a rechargeable lithium ion battery. Its ability to generate power comes 
from the chemical reaction that takes place inside it. This reaction is susceptible to 
the surrounding temperature and humidity. If the temperature is too high or too low, 
the operating time of the battery will become shorter.
Always remove the battery after use.
•
Place the removed battery in a plastic bag, and store or keep away from metallic objects (clips, 
etc.).
If you drop the battery accidentally, check to see if the body of the battery and the 
terminals are damaged.
•
Inserting a damaged battery in the camera will damage the camera.
Bring charged spare batteries when going out.
•Be aware that the operating time of the battery becomes shorter in low temperature conditions 
such as at a ski resort.
•When you travel, do not forget to bring the AC adaptor (supplied) and USB connection cable 
(supplied) so that you can charge the battery in the country that you are travelling in.
Dispose of unusable battery.
•The battery has a limited life.•Do not throw the battery into fire because it may cause an explosion.
Do not allow battery terminals to come into contact with metal objects (such as 
necklaces, hairpins, etc.).
•
This can cause short-circuiting or heat generation and you may be badly burned if you touch a 
battery.
•If you use the AC adaptor (supplied) near a  radio, the radio reception may be disturbed.•Keep the AC adaptor (supplied) 1 m (3.3 feet) or further away from radios.•The AC adaptor (supplied) may generate whirring  sounds when it is being used. This is not a 
malfunction.
•After use, be sure to disconnect the power supply device from the electrical outlet. (A very 
small amount of current is consumed if it is left connected.)
Battery
AC adaptor (supplied) 
						

							Others
- 154 -
∫About 3D viewing
Anyone who is hyper sensitive to light, suffers from heart disease or is otherwise 
unwell should avoid viewing 3D contents.
•
Viewing 3D contents may have an adv erse effect to the individual.
If you feel tired, uncomfortable or otherwise strange when viewing 3D contents, 
stop viewing at once.
•
Continuing to view may cause illness.•After stopping viewing, please rest appropriately.
When viewing 3D contents, we recommend taking a break every 30 to 60 minutes.
•Viewing for extended periods may cause eye-fatigue.
Short-sighted or long-sighted persons, those with differences in the sight of their 
right and left eyes, and those with astigmatism are advised to correct their vision by 
wearing glasses etc.
Stop viewing if you can clearly see a double image while viewing 3D contents.
•
There are differences in the way that different  people experience 3D contents. Please correct 
your sight appropriately before viewing 3D contents.
•You can change the 3D setting of your television or 3D output setting of the unit to 2D.
About 3D 
						

							- 155 -
Others
Do not leave the card where the temperature is high, where electromagnetic waves 
or static electricity are easily generated or exposed to direct sunlight.
Do not bend or drop the card.
•
The card may be damaged or the recorded content may be damaged or deleted.•Put the card in the card case or the storage bag after use and when storing or carrying the 
card.
•Do not allow dirt, dust, or water to get into the terminals on the back of the card and do not 
touch the terminals with your fingers.
Notice for when transferring to another party, or disposing of the memory card
•“Format” or “delete” using the camera or a PC will only modify the file management information, 
it will not erase the data in the memory card completely.
It is recommended to physically destroy the memory card or use the commercially available 
computer data deletion software to completely erase the data in the memory card before 
transferring to another party or disposing.
Management of data in the memory card is the responsibility of the user.
If a name or birthday is set for [Baby1]/[B aby2]/Face Recognition function, this personal 
information is kept in the camera and recorded in the image.
Disclaimer
•
Information including personal information may be altered or vanish due to erroneous 
operation, effect of static electricity, accident, malfunction, repair, or other handlings.
Please note in advance that Panasonic is not liable in any way for any direct or indirect damage 
from the alteration or vanishing of information or personal information.
When requesting a repair, transferring to another party, or disposing
•Reset the settings to protect the personal information.  (P48)•If there are pictures stored in the built-in memory, copy them into the memory card  (P118) 
before formatting the built-in memory  (P51) as needed.
•Remove the memory card from the camera when requesting a repair.•Built-in memory and settings may return to factory default when camera is repaired.•Please contact the dealer where you purchased the camera or your nearest Service Centre if 
above operations are not possible due to malfunction.
When transferring to another party, or disposing of the memory card, please refer to 
“Notice for when transferring to another party, or disposing of the memory card” 
above.
Card
About the personal information 
						

							Others
- 156 -
•Store the battery in a cool and dry place with a relatively stable temperature: (Recommended 
temperature: 15oC to 25 oC (59 oF to 77 oF), Recommended humidity: 40%RH to 60%RH)
•Always remove the battery and the card from the camera.•If the battery is left inserted in the camera, it will discharge even if the camera is turned off. If 
the battery continues to be left in the camera, it will discharge excessively and may become 
unusable even if charged.
•When storing the battery for a long period of time, we recommend charging it once a year. 
Remove the battery from the camera and store it again after it has completely discharged.
•We recommend storing the camera with a desiccant  (silica gel) when you keep it in a closet or 
a cabinet.
•Recorded data may be damaged or lost if the camera breaks down due to inappropriate 
handling. Panasonic will not be liable for any damage suffered due to loss of recorded data.
•When you use a tripod, make sure the tripod is stable when this unit is attached to it.•You may not be able to remove the card or the battery when using a tripod or unipod.•Make sure that the screw on the tripod or unipod is not at an angle when attaching or detaching 
the camera. You may damage the screw on the camera if you use excessive force when 
turning it. Also, the camera body and the rating label may be damaged or scratched if the 
camera is attached too tightly to the tripod or unipod.
•Read the operating instructions for the tripod or unipod carefully.•Some tripods or unipods may block the speaker, making it difficult to hear operating sounds etc.
When not using the camera for a long period of time
About the picture data
About tripods or unipods 
						

							- 157 -
Others
Message Display
Confirmation messages or error messages will be displayed on the screen in some cases.
The major messages are described below as examples.
[This picture is protected]
>Delete the picture after cancelling the protect setting.  (P116)
[Some pictures cannot be deleted]/[This picture cannot be deleted]
•
Pictures not based on the DCF standard cannot be deleted.
> If you want to delete some pictures, format the card after saving necessary data on a PC 
etc.  (P51)
[Cannot be set on this picture]
•
[Title Edit], [Text Stamp] or [Print Set] cannot be set for pictures not based on the DCF 
standard.
[Built-in memory full]/[Memory card full]/[Not enough space on built-in memory]/
[Not enough memory on the card]
•
There is no space left on the built-in memory or the card.•When you copy pictures from the built-in memory to the card (batch copy), the pictures are 
copied until the capacity of the card becomes full.
[Some pictures cannot be copied]/[Copy could not be completed]
•
The following pictures cannot be copied.–When a picture with the same name as the picture to be copied exists in the copy 
destination. (Only when copying from a card to the built-in memory.)
–Files not based on the DCF standard.•Moreover, pictures recorded or edited by other equipment may not be copied.
[Built-In Memory Error]/[Format built-in memory?]
•
This message will be displayed when y ou format the built-in memory on a PC.
> Format the built-in memory on the camera again.  (P51) The data on the built-in memory 
will be deleted. 
						

							Others
- 158 -
[Memory card error. 
This card cannot be used in this camera. 
Format this card?]
•
It is a format that cannot be used with this unit.> Insert a different card and try again.
> Reformat on this unit (P51)  after saving necessary data using a PC, etc. Data will be 
deleted.
[Please turn camera off and then on again]/[System Error]
•
This message appears when the camera is not operating properly.
> Turn the camera off and on. If the message persists, contact the dealer or your nearest 
Service Centre.
[Memory Card Error]/[Memory card parameter error]/[This memory card cannot be 
used]
>Use a card compatible with this unit.  (P16)–SD Memory Card (8 MB to 2 GB)–SDHC Memory Card (4 GB to 32 GB)–SDXC Memory Card (48 GB, 64 GB)
[Insert SD card again]/[Try another card]
•
An error has occurred accessing the card.
> Insert the card again.
> Insert a different card.
[Read Error/Write Error 
Please check the card]
•
It has failed to read or write data.
> Remove the card after turning the power [OFF]. Insert the card again, turn the power on, 
and try to read or write the data again.
•The card may be broken.
> Insert a different card.
[Motion recording was cancelled due to the limitation of the writing speed of the 
card]
•
Use a card with SD Speed Class with “Class 4”  or higher when recording motion pictures.•In the event that it stops even after using a “Class 4” card or higher, the data writing speed has 
deteriorated so it is recommended to make a backup and then format  (P51).
•Depending on the type of the card, motion picture recording may stop in the middle. 
						

							- 159 -
Others
[Cannot record due to incompatible format(NTSC/PAL) data on this card.]
>Format the card after saving necessary data on a PC etc.  (P51)
> Insert a different card.
[A folder cannot be created]
•
A folder cannot be created because there are no remaining folder numbers that can be used.
> Format the card after saving necessary data on a PC etc.  (P51) If you execute [No.Reset] 
in the [Setup] menu after formatting, the folder number is reset to 100.  (P48)
[Picture is displayed for 16:9 TV]/[Picture is displayed for 4:3 TV]
•
Select [TV Aspect] in the [Setup] menu if you want to change the TV aspect. (P49)•This message also appears when the USB connection cable is connected to the camera only.
In this case, connect the other end of the USB connection cable to a PC or a printer.  (P140, 
144)
[Recording failed.]
•
You may not record when the recording location is too dark/too bright, or if the subject does 
not have enough contrast when recording in 3D.
[This battery cannot be used]
•
Use a genuine Panasonic battery. If this message is displayed even when a genuine 
Panasonic battery is used, contact the dealer or your nearest Service Centre.
•If the battery terminal is dirty, clean it and remove any objects. 
						

							Others
- 160 -
Troubleshooting
First, try out the following procedures (P160–170).
•
This phenomenon occurs when charging in a location where the temperature is very high or 
very low. > Reconnect the USB connection cable (supplied) in a location where the ambient 
temperature (and the temperature of battery) is in a 10 oC to 30 oC (50 oF to 86 oF) range, 
and try charging again. [If you reconnect the USB connection cable (supplied) when the 
unit is fully charged, the charging lamp  will turn on for approximately 15 seconds.]
•The battery is exhausted. Charge the battery.•If you leave the camera on, the battery will be exhausted.
> Turn the camera off frequently by using the [Economy].  (P47)
•If you connect to a TV compatible with VIERA Link with a HDMI mini cable (optional) and turn 
off the power on the TV with the remote control for the TV, the power on this unit also turns off.
> If you are not using VIERA Link, set [VIERA Link] to [Off].  (P49)
•Insert the battery securely all the way in. (P10)
If the problem is not resolved, it may be improved by selecting [Reset]  (P48) on the 
[Setup] menu.
Battery and power source
The charging lamp has gone off but the unit has not been charged.
The camera cannot be operated even when it is turned on.
The camera turns off immediately after it is turned on.
This unit is turned off automatically.
Card/battery door does not close.