Panasonic Kx Taw848 Feature Manual

							2.3 System Data Control
Feature Guide 191
Extension Numbering Scheme 7–32—Leading 
NumberNone None
Operator Call00
Idle Line Access (Local Access)99
CO Line Group Access88
Redial##
Speed Dialing—System/Personal
Personal Speed Dialing—Programming
3030
Doorphone Call
3131
Group Paging
3333
External BGM on/off
3535
Outgoing Message (OGM) playback/record/
clear3636
S-CO Line Access
3737
Group Call Pickup
4040
Directed Call Pickup
4141
TA FA S—Calls through an External Pager
4242
Group Paging answer
4343
Automatic Callback Busy cancel
4646
User Remote Operation/Walking COS/Verified 
Code Entry4747
Wireless XDP Parallel Mode set/cancel
4848
Account Code Entry
4949
Call Hold/Call Hold Retrieve
5050
Call Hold Retrieve—Specified with a Holding 
Extension Number5151
Call Park/Call Park Retrieve
5252
Call Hold Retrieve—Specified with a Held CO 
Line Number5353
Door Open
5555
External Feature Access
6060
Message Waiting set/cancel/callback
7070 Feature Default
Pattern 1 
(with )Pattern 2 
(without ) 
						

							2.3 System Data Control
192 Feature Guide
FWD/DND set/cancel—Both 
710710
FWD/DND set/cancel—External
711711
FWD/DND set/cancel—Internal
712712
FWD/DND No Answer Timer set
713713
Group FWD set/cancel—Both 
714714
Group FWD set/cancel—External
715715
Group FWD set/cancel—Internal
716716
Call Pickup Deny set/cancel
720720
Paging Deny set/cancel
721721
Walking Extension
727727
Data Line Security set/cancel
730730
Call Waiting for Intercom Calls set/cancel
731731
Call Waiting for CO Line Calls (including 
doorphone calls, calls for an incoming call 
distribution group) set/cancel732732
Executive Busy Override Deny set/cancel
733733
Not Ready Mode on/off
735735
Log-in/Log-out
736736
Hot Line program/set/cancel
740740
Absent Message set/cancel
750750
BGM set/cancel
751751
Timed Reminder set/cancel
760760
Extension Lock set/cancel
7777
Time Service Switch
780780
Remote Extension Lock off
782782
Remote Extension Lock on
783783
Extension Feature Clear
790790
Extension Personal Identification Number (PIN) 
set/cancel799799
Quick Dialing 1–80None None Feature Default
Pattern 1 
(with )Pattern 2 
(without ) 
						

							2.3 System Data Control
Feature Guide 193
2.Flexible Numbering (available while a busy, DND, or ringback tone is heard) 
Feature numbers which are available while a busy, DND, or ringback tone is heard can be 
customized for easy use. The numbers should be one digit (0–9,  , or # ) and must not 
conflict. For a list of the default settings, refer to the following table:
[Flexible Numbering Table (available while a busy, DND, or ringback tone is heard)]
3.Fixed Numbering (available while dialing or talking)
Features which are available while dialing or talking have fixed numbers, as shown in the 
following table:
[Fixed Numbering Table (available while dialing or talking)]
Conditions
The following are examples of feature number conflicts: 1 and 11, 0 and 00, 2 and 21, 10 
and 101, 32 and 321, etc.
Feature number + Additional number (Parameter)
Certain flexible feature numbers require additional digits to make the feature active. For 
example, to set Call Waiting, the feature number for Call Waiting must be followed by 1 
and to cancel it, the same feature number should be followed by 0.
Rotary single line telephone (SLT) users cannot dial feature numbers which include   or 
#.
Portable station (PS) users cannot use the following features:Feature Default
Call Waiting/DND Override1 or 2*
Executive Busy Override3
Message Waiting set4
Call Monitor5
Automatic Callback Busy6
Alternate Calling—Ring/Voice
* To use Call Waiting/DND Override, both 1 and 2 are available by default.
Feature Fixed 
Numbering
Pulse to Tone Conversion
Conference3
Door Open5
–Personal Speed Dialing
–OGM playback/record
–S-CO Line Access
–Walking Extension
–BGM set/cancel 
						

							2.3 System Data Control
194 Feature Guide
User Manual References
User Manual
4.2.1 Feature Number Table
2.3.6 Floating Extension
Description
Virtual extension numbers can be assigned to resources to make them as easily accessible as 
extensions.
These numbers are referred to as floating extension numbers and can be assigned as a 
destination of incoming calls, intercepted calls, etc.
This feature is also known as Floating Station.
Conditions
Certain resources which are assigned a floating extension number can also be assigned 
a name (  ICD Group Name [623],   Outgoing Message (OGM) Name [731]).
Feature Guide References
1.19.1 Voice Mail (VM) Group
2.3.1 PC Programming–Timed Reminder
Resource Description
Device External PagerUsed as the destination for the Trunk Answer From Any 
Station (TAFAS) feature (  External Pager Floating 
Extension Number [700]). (  1.15.3 Trunk Answer From 
Any Station (TAFAS))
Outgoing Message 
(OGM)Used to play messages for callers via the Direct Inward 
System Access (DISA) feature (  Outgoing Message 
(OGM) Floating Extension Number [730]). (  1.15.6 
Direct Inward System Access (DISA))
Analog Remote 
MaintenanceUsed to access PC programming mode through a modem 
on a PC (  Modem Floating Extension Number [811]).
Group Incoming Call 
Distribution (ICD) 
GroupUsed to call an ICD group (  ICD Group Floating 
Extension Number [622]). (  1.2.2.1 Incoming Call 
Distribution (ICD) Group Features—OVERVIEW)
PS Ring GroupUsed to call a PS ring group. (  1.20.2 PS Ring Group)
VM (DPT) GroupUsed to call a VM (DPT) group (  VM Group Floating 
Extension Number [660]).
VM (DTMF) GroupUsed to call a VM (DTMF) group. 
						

							2.3 System Data Control
Feature Guide 195
2.3.7 Software Upgrading
Description
It is possible to upload software from a PC to the PBX to upgrade the following:
Conditions
The software version of the MPR can be confirmed through system programming (  Main 
Processing (MPR) Software Version Reference [190]).Data File Storing Area
Main Processing (MPR) 
software dataOperating system data area on the Main 
Board
Default system programming 
data for each country/areaCountry/area data area on the Main Board
Language data for PT display Each language data area on the Main 
Board.
There are two types:
Ty p e  1 :  Proprietary telephone (PT) display 
except for PT system programming (  
2.3.2 PT Programming) (five languages 
max.)
Ty p e  2 : PT system programming data (one 
language max.)
Cell Station (CS) software data Flash ROM on the CS 
						

							2.4 Fault Recovery/Diagnostics
196 Feature Guide
2.4 Fault Recovery/Diagnostics
2.4.1 Power Failure Transfer
Description
If the power supply to the PBX fails, specific single line telephones (SLTs) are automatically 
connected to specific CO lines (Power Failure Connections). The PBX will switch from the 
current connections to Power Failure Connections, and all existing conversations will be 
disconnected.
Only CO line conversations handled by Power Failure Connections can be made during a 
power failure.
Conditions
Only ports 1 and 2 of the preinstalled LCOT4 card and ports 1 and 2 of the preinstalled 
hybrid ports can be used for Power Failure Connections.
Note
When power is restored to the PBX and the Main Board is recovering, Power Failure 
Connections remain established so that any existing conversations can be maintained.
Only CO line conversations are possible during a power failure. All other features will not 
work.
Installation Manual References
Installation Manual
2.10.1 Power Failure Connections
2.4.2 Power Failure Restart
Description
When the electricity is turned back on, the PBX restarts, loads its stored data automatically, 
and logs the event as a System Restart in the error log.
Conditions
In the event of a power failure, PBX memory is protected by a factory-installed lithium 
battery. There is no memory loss except the memories of Automatic Callback Busy 
(Camp-on) (  1.7.1 Automatic Callback Busy (Camp-on)) and Call Park (  1.12.2 Call 
Par k). 
						

							2.4 Fault Recovery/Diagnostics
Feature Guide 197
2.4.3 Local Alarm Information
Description
When the PBX detects an error, the System Alarm button on the proprietary telephone (PT) of 
an extension which is allowed to use this feature through system programming (a maximum of 
two extensions per PBX), lights red. Pressing the button will show the error number on the 
display. If multiple errors occur, the error number will be displayed in order of highest priority to 
lowest. The System Alarm button light turns off automatically after all error numbers have been 
displayed.
For details regarding errors and their solutions, refer to the Installation Manual.
[Error Example]
[Explanation]
Conditions
System Alarm Button
Any flexible button can be customized as the System Alarm button.
The alarm information will be logged on the Station Message Detail Recording (SMDR) if 
enabled through system programming.
The PBX can be automatically diagnosed at a preprogrammed time everyday.
Installation Manual References
Installation Manual
4.1.5 Troubleshooting by Error Log
Feature Guide References
1.18.2 Flexible ButtonsNumber in the 
ExampleItem Description
(1) Error CodeShows three-digit error code.
(2) Sub CodeShows five-digit sub code (XYYZZ).
X: Cabinet number (1–4)
YY: Slot number (00–11)
ZZ: Physical port number (01–08)
ERR #100 (10000)
(1)(2) 
						

							2.4 Fault Recovery/Diagnostics
198 Feature Guide
1.21.1 Station Message Detail Recording (SMDR) 
						

							Feature Guide 199
Section 3
Programming Instructions 
						

							3.1 Introduction
200 Feature Guide
3.1 Introduction
3.1.1 Introduction
These programming instructions are designed to serve as an overall system programming 
reference for the PBX.
The PBX has default settings which can be changed to meet your needs. These settings 
control the manner in which the PBX features described in this Feature Guide function, and 
changing these settings is referred to as system programming.
System programming can be performed by only one person at a time. A second person 
attempting to program the system will be denied access to system programming.
Ways to Program
There are two programming methods:
PC Programming
All system programming can be performed. PC programming is described in Section 
3.2 PC Programming.
PT (Proprietary Telephone) Programming
A subset of system programming can be performed. PT programming is described in 
Section 3.3 PT Programming. An extension user can perform system programming 
by entering 3-digit programming numbers with a PT.