Panasonic Projector PT-RZ575 User Manual

Chapter 7 Appendix — Technical information
ENGLISH - 171
 rError response
String DetailsTermination 
symbol
Message “ERR1” Undefined control command
(CR)
0x0d
“ERR2”
Out of parameter range
“ERR3” Busy state or no-acceptable period
“ERR4” Timeout or no-acceptable period
“ERR5” Wrong data length
“ERRA” Password mismatch
Data length 4
  bytes ―1
  byte
 terminal
The  terminal of the projector conforms with RS-232C so that the projector can be connected to and 
controlled from a computer .
Connection
When...

Chapter 7 Appendix — Technical information
172 - ENGLISH
Communication conditions (Factory default)
Signal levelRS - 232C-compliant
Sync. method Asynchronous
Baud rate 9
  600   bps
Parity None
Character length 8 bits
Stop bit 1 bit
X parameter None
S parameter None
Basic format
Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this 
order. Add parameters according to the details of control.
(2 bytes)
2 ID characters (2 bytes) Semi-colon (1 byte) Colon...

Chapter 7 Appendix — Technical information
ENGLISH - 173
Cable specification
1NC    NC 1
2 2
3 3
4 NC    NC 4
5 5
6 NC    NC 6
7 7
8 8
9 NC    NC 9
When connected to a computer
Projector
( terminal) Computer
(DTE specifications)
Control command
The following table lists the commands that can be used to control the p\
rojector using a computer.
 r
Projector control command
Command Details Parameter/response 
string Remark (parameter)
PON Power on
―To check if the power is on, use the “Power query”...

Chapter 7 Appendix — Technical information
174 - ENGLISH
 rLens control command
Command Sub command Details Remark
VXX LNSI2 Lens H shift
+00000 = Fine adjustment 1+, +00001 = Fine adjustment 1
-, +00100 
= Fine adjustment 2+, +00101 = Fine adjustment 2-, +00200 = Coarse 
adjustment+, +00201 = Coarse adjustment-VXX LNSI3 Lens V shift
VXX LNSI4 Lens focus
Two-window display combination list
l: P IN P (picture in picture) combination is possible
―: P IN P (picture in picture) combination is not possible...

Chapter 7 Appendix — Technical information
ENGLISH - 175
List of compatible signals
The following table specifies the video signals compatible with the projector.
 fSymbols that indicate formats are as follows.
 gV

: VIDEO, Y/C
 gR: RGB (analog)
 gY

: YC
BCR/YPBPR (analog)
 gD: DVI

-
D
 g H: HDMI
 fInput corresponding to each item in the plug and play column is as follows.
 gCOMPUTER: COMPUTER1/COMPUTER2 input
 gDVI

-
D: DVI
-
D input
 g HDMI/DL: HDMI1/HDMI2 input, DIGIT

AL LINK input
Signal name...

Chapter 7 Appendix — Technical information
176 - ENGLISH
Signal name
(SIGNAL FORMAT) Resolution
(Dots) Scanning freq.
Dot clock 
freq.
(MHz) Format Plug and play*1
Horizontal
(kHz)Vertical(Hz)COMPUTERDVI-D HDMI/
DL
EDID1 EDID2 EDID3
1
152
 
x
 
864/60 1
 
152
 
x
 
864 53.7  60.0  81.6  R/D/H ― ― ― ― ―
1152
 
x
 
864/70 1
 
152
 
x
 
864 64.0  70.0  94.2  R/D/H ― ― ― ― ―
1152
 
x
 
864/75 1
 
152
 
x
 
864 67.5  75.0  108.0  R/D/H ― ― ― ― ―
1152
 
x
 
864/85 1
 
152
 
x
 
864 77.1  85.0  119.7  R/D/H ― ―...

Chapter 7 Appendix — Technical information
ENGLISH - 177
 fThe “i” at the end of the resolution indicates an interlaced signal. fWhen interlaced signals are connected, flickering may occur on the projected image. fDIGIT

AL LINK input compatible signal is the same as HDMI input compatible signal.  

Chapter 7 Appendix — Specifications
178 - ENGLISH
Specifications
The specifications of the projector are as follows.
Power supplyPT- RZ575
100   V - 240   V ~ (100   V - 240   V alternating current), 50   Hz/60   Hz
PT- RZ575T110
  V ~ (110   V alternating current), 60   Hz
Power consumption PT
-

RZ575500
  W (5.9  
A
  - 2.3  
A)
PT
-

RZ575T500
  W (5.2  
A)
Power consumption (during 
standby) When [ST

ANDBY MODE] is set to [ECO]: approx. 0.5   W
When [STANDBY MODE] is set to [NORMAL]: approx. 10...

Chapter 7 Appendix — Specifications
ENGLISH - 179
 rConnecting terminal
 terminal 1 set, high-density D - Sub 15   p (female)
RGB signal 0.7   V [p-p] 75   Ω (SYNC ON GREEN: 1.0   V [p-p] 75   Ω)
SYNC/HD TTL high impedance, automatic positive/negative 
polarity compatible
VD TTL high impedance, automatic positive/negative 
polarity compatible
YP
BPR signal Y: 1.0   V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω
Y/C signal Y
: 1.0
 
V [p-p], C: 0.286
 
V [p-p] 75
 
Ω
 
terminal 1 set,...

Chapter 7 Appendix — Specifications
180 - ENGLISH
 rCompatible signal
For details of the types of video signals that can be used with the projector , refer to “List of compatible signals” 
(x   page   175).
Video input, Y/C input
Horizontal: 15.73
  kHz, Vertical: 59.94   Hz; Horizontal: 15.63   kHz, Vertical: 50   Hz
RGB input
 f Resolution: 640

  x   400 to 1   920   x   1   200
 fDot clock frequency: 162

  MHz or less
 fPIAS (Panasonic Intelligent 

Auto Scanning) system
YC
BCR/YPBPR input
 f...