Ricoh Mp C6502 User Guide

							Sort
The machine assembles copies as sets in sequential order.
• You cannot use the bypass tray with Rotate Sort.
Sort/Shift Sort
Copies are assembled as sets in sequential order.
To use Shift Sort, a finisher is required. Each time the copies of one set or a job are delivered, the
next copy is shifted to separate each set or job.
Rotate Sort
Every other copy set is rotated by 90 degrees (
) and delivered to the copy tray.
To use the Rotate Sort function, two paper trays loaded with paper of the same size and type, but in
different orientation (
), are required.
For details, see "Tray Paper Settings", Connecting the Machine/ System Settings
.
Sort
71 CKN018   CKN019       
						

							1.Press [Finishing].
2.Press [Finisher].
3. Select [Sort] or [Rotate Sort], and then press [OK].
4.Enter the number of copy sets using the number keys.
5. Place the originals.
To confirm the type of finishing, press the [Sample Copy] key.
6. Press the [Start] key.
Changing the Number of Sets
You can change the number of copy sets during copying.
• This function can be used only when the Sort function is selected.
1. While "Copying..." is displayed, press the [Stop] key.
3. Copy
72   
						

							2.Enter the number of copy sets with the number keys.
3.Press [Continue].
Copying starts again.
Sort
73  
						

							Storing Data in the Document Server
The Document Server enables you to store documents being read with the copy feature on the hard disk
of this machine. Thus you can print them later applying necessary conditions.
You can check the stored documents on the Document Server screen. For details about the Document
Server, see page 115 "Storing Data".
1. Press [Store File].
2.Enter a file name, user name, or password if necessary.
3. Specify a folder in which to store the document if necessary.
4. Press [OK].
5. Place the originals.
6. Make the scanning settings for the original.
7. Press the [Start] key.
Stores scanned originals in memory and makes one set of copies. If you want to store another document, do so after copying is complete.
3. Copy
74  
						

							4. Fax
This chapter describes frequently used facsimile functions and operations. For the information not
included in this chapter, see Fax
 on the supplied CD-ROM.
Basic Procedure for Transmissions (Memory
Transmission)
This section describes the basic procedure for transmitting documents using Memory Transmission.
You can specify the fax, IP-Fax, Internet Fax, e-mail, or folder destinations. Multiple types of destination
can be specified simultaneously.
• It is recommended that you call the receivers and confirm with them when sending important documents.
• If there is a power failure (the main power switch is turned off) or the machine is unplugged for about one hour, all the documents stored in memory are deleted. As soon as the main power
switch is turned on, the Power Failure Report is printed to help you check the list of deleted files. See
"When an Error Is Notified via a Report or E-mail", Troubleshooting
.
1. Press the [Home] key on the top left of the control panel, and press the [Facsimile] icon on
the [Home] screen.
2. Make sure "Ready" appears on the screen.
75   CJS113   
						

							3.Make sure [Immed. TX] is not highlighted.
4.Place the original into the ADF.
5. Make the scan settings such as scan size and resolution.
6.Configure the transmission settings such as [TX Mode] as necessary.
7. Specify a destination.
You can enter the destination's number or address directly or select from the Address Book by
pressing the destination key.
If you make a mistake, press the [Clear] key, and then enter again.
8. When sending the same original to several destinations (broadcasting), specify the next
destination.
4. Fax
76  
						

							9.If you send documents to Internet Fax or e-mail destinations or enable the E-mail TX
Results function, specify a sender.
10. Press the [Start] key.
Sending Originals Using the Exposure Glass (Memory Transmission)
1. Make sure [Immed. TX] is not highlighted.
2.Place the first page of the original face down on the exposure glass.
3. Specify a destination.
4. Make the scan settings you require.
5. Press the [Start] key.
6. Place the next original on the exposure glass within 60 seconds when you send multiple
originals, and then repeat steps 4 and 5.
Repeat this step for each page.
7. Press the [] key.
The machine dials the destination and starts transmission.
Basic Procedure for Transmissions (Memory Transmission)
77   
						

							Registering a Fax Destination
1.Press the [User Tools/Counter] key.
2. Press [Address Book Mangmnt].
3. Check that [Program / Change] is selected.
4. Press [New Program].
5. Press [Change] under "Name".
The name entry display appears.
6. Enter the name, and then press [OK].
7. Press [
Next].
8. Press the key for the classification you want to use under "Select Title".
The keys you can select are as follows:
• [Frequent]: Added to the page that is displayed first.
• [AB], [CD], [EF], [GH], [IJK], [LMN], [OPQ], [RST], [UVW], [XYZ], [1] to [10]: Added to the list of items in the selected title.
You can select [Frequent] and one more key for each title.
9. Press [Fax Dest.].
10. Press [Change] under "Fax Destination".
4. Fax
78   
						

							11.Enter the fax number using the number keys, and then press [OK].
12.Specify optional settings such as "SUB Code", "SEP Code", and "International TX Mode".
13. Press [OK].
14. Press [Exit].
15. Press the [User Tools/Counter] key.
Deleting a Fax Destination
• If you delete a destination that is a specified delivery destination, messages to its registered Personal Box, for example, cannot be delivered. Be sure to check the settings in the fax function
before deleting any destinations.
1. Press the [User Tools/Counter] key.
2. Press [Address Book Mangmnt].
3. Check that [Program / Change] is selected.
4. Select the name whose fax destination you want to delete.
Press the name key, or enter the registered number using the number keys. You can search by the registered name, user code, fax number, folder name, e-mail address, or IP-Fax destination.
5. Press [Fax Dest.].
6. Press [Change] under "Fax Destination".
Basic Procedure for Transmissions (Memory Transmission)
79   
						

							7.Press [Delete All], and then press [OK] under "Fax Destination".
8.Press [OK].
9. Press [Exit].
10. Press the [User Tools/Counter] key.
4. Fax
80