Samsung Ht D7500w User Manual

							
0 English
English 1

02
Connections

Connecting the Subwoofer
To activate the product, you must connect the subwoofer to the product using the system cable. 
Most of external connections including power supply, speakers and TV are made through the 
subwoofer.
CAUTION
Do not plug or unplug the system cable during the power cord is plugged. Otherwise, it can cause damage to the product.
Attaching the Toroidal Ferrite Core to the Power Cord of the Subwoofer
If you attach a Toroidal ferrite core to the power cord of the 
Subwoofer, it will help to prevent RF interference from radio 
signals.
Pull the fi xing tab of the Toroidal ferrite core to open it. 
Make a loop once in the power cable of the subwoofer.
Attach the Toroidal ferrite core to the Subwoofer power cord as the fi gure shows and press it until it clicks.
Attaching the Toroidal Ferrite Core to the System Cable
Pull the fi xing tab of the Toroidal ferrite core to open it.
Insert two cores into one end of the system cable, and the other core into the other end of the system cable (connected between product and subwoofer). Then, press to close the cores until you hear a click as shown.-  Unlike attaching ferrite core to the power cable, do not make loops around the core with the 
system cable and simply plug in the core and fi x it.
!

1.
2.
3.
1.
2.
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3
DC 12ViPodSYSTEMCABLELAN
SYSTEM CABLE
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3
DC 12ViPodSYSTEMCABLELAN
SYSTEM CABLEONLY FORUPDATE
 
						

							
 English

Connections

English 

Connecting The Speakers
Press down the terminal tab on the back of the speaker. 
Insert the black wire into the black terminal (–) and the red wire into the red (+) terminal, and then release the tab.
Connect the speaker wire plugs to the back of the product by matching the colors of the speaker plugs to the speaker jacks.
With the product turned off, insert the TX card into the TX Card Connection (WIRELESS) on the back of the product.Hold the TX card so that the label "WIRELESS" faces upward and insert the card into the port. The TX card enables communication between the product and the wireless receiver module. 
Connect the left and right surround speakers to the wireless receiver module. 
Plug the power cord of the wireless receiver module into the wall outlet.
Turn on the product. The product and wireless receiver module will now communicate with each other and you will hear sound from the Surround speakers.
1.
2.
3.
4.
•
•
5.
6.
7.
BlackRed
HDMI IN 1HDMI IN 2
SPEAKERS OUTFRONTFRONT
WIRELESS
SPEAKER IMPEDANCE : 3
TX card
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3
DC 12ViPodSYSTEMCABLELAN
SYSTEM CABLE
SPEAKERS OUTFRONTFRONT
CENTER
Front Speaker (R)
Subwoofer
Centre Speaker
Wireless Receiver Module
Surround Speaker (L)
This product should be connected with the SWA-5000 only.
Surround Speaker (R)
Front Speaker (L)
Attaching the Toroidal Ferrite Core to the Speaker Cables of the Subwoofer
If you attach a Toroidal ferrite core to the Speaker Cables of the subwoofer, it will help to prevent RF interference from radio signals.
Pull the fi xing tab of the Toroidal ferrite core to open it.
Make a loop once in the Speaker Cables.
Attach the Toroidal ferrite core to the Speaker Cables of the Subwoofer as the fi gure shows and press it until it clicks.
1.
2.
3.
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2
FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESS
ASC INSPEAKER IMPEDANCE : 3
 
						

							
 English
English 

02
Connections

CAUTION
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/ –) is correct.
  Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien substances into the duct (hole) of the subwoofer speaker.
  Do not hang the subwoofer on the wall through the duct (hole).
Do not insert any other card except the TX card dedicated to the product. If you insert a different TX card, you can damage the product and may not be able to remove the card easily.
Do not insert the TX card upside down or in the reverse direction.
  Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem.
 The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.
For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.
If no sound is heard from the wireless surround speakers, switch the mode to Dolby Pro Logic II.
In 2-CH mode, you will hear no sound from the wireless surround speakers.
NOTE
 If you place a speaker near your TV set, the screen colour may be distorted because of the magnetic fi eld.
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, sound from the speakers may be disrupted because of interference.
If you use a device such as a microwave oven, wireless LAN Card, or any other device that uses the 2.4/5.8GHz frequencies near the product, sound from the speakers may be disrupted because of interference.
The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal.
If the product doesn't make a wireless connection, you need to run an ID Set between the product and wireless receiver module. With the product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the "ID SET" button on the back of the wireless receiver module for 5 seconds, and then turn the product on.
!











✎





Connecting the fm antenna
Connect the FM antenna supplied to the FM 
ANTENNA Jack.
Slowly move the antenna wire around until you fi nd 
a location where reception is good, then fasten it 
to a wall or other rigid surface.
NOTE
  This product does not receive AM broadcasts.
1.
2.
✎
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2AUX INSPEAKERS OUTFRONTFRONTCENTER
WIRELESSASC INSPEAKER IMPEDANCE : 3SPEAKER IMPEDANCE : 3
FMANT
FM Antenna (supplied)
 
						

							
 English

Connections

English 

Connecting external Devices/your tv via HDmI
HDMI is the standard digital interface for connecting to devices such as a TV, projector, DVD player, Blu-ray 
player, set top box, and more.
Because HDMI is all digital, you'll enjoy digital quality video and sound as it was originally created, without 
the distortions that can be caused when digital content is converted to analogue.
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on 
your TV.
 NOTE
Certain HDMI output resolutions may not work, depending on your TV.
After making the video connection, set the Video input source on your TV to match the corresponding Video 
output (HDMI or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote 
control and select HDMI as the external source of the TV.
You must have an HDMI connection to enjoy videos with 3D technology.
A long HDMI cable may cause screen noise. If this occurs, set Deep Colour to Off in the menu.
HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack on your digital 
device.
Press the FUNCTION button to select HDMI1 or HDMI2 input.
The mode switches as follows : BD/DVD ; D. IN ; AUX ; R. iPod ; W. iPod ; HDMI1 ; HDMI2 ; TUNER
✎





1.
2.
SYSTEM CABLEONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)HDMI OUTHDMI IN 1HDMI IN 2FM ANTAUX INSPEAKERS OUTFRONTFRONTCENTERWIRELESSASC INSPEAKER IMPEDANCE : 3
SYSTEM CABLE
ONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)
HDMI OUTHDMI IN 1HDMI IN 2
FM ANT
AUX INSPEAKERS OUTFRONTFRONT
CENTER
WIRELESS
ASC IN
SPEAKER IMPEDANCE : 3
HDMI OUT
HDMI IN
DVD or Blu-ray PlayerSAT (Satellite/Set top box)
HDMI IN
 
						

							
 English
English 

02
Connections

HDMI Auto Detection Function
If you have connected your home cinema by HDMI cable, the home cinema's video output 
automatically switches to the HDMI mode when you turn it on. For available HDMI video resolutions, 
see page 32.
This function is not available if the HDMI cable does not support CEC.
HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
-  If your TV does not support HDCP, random noise appears on the screen.
What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for preventing BD/DVD content outputted via 
HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display 
device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being 
made.
CAUTION
The Anynet+ function is supported only when an HDMI Cable is connected to the HDMI OUT of the 
product.
•
•
•
!

Composite Video (GOOD QUALITY) 
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO 
IN jack on your TV.
NOTE
The VIDEO source always outputs in 576i/480i resolution regardless of the resolution set in the Setup menu. (See page 32)After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI or Composite) on your product.See your TV owner's manual for more information on how to select the TV's Video Input source.If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control and select VIDEO as the external source of the TV.
CAUTION
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and the picture will be distorted on the television.
✎



!

DC 12ViPodSYSTEMCABLELAN
Video Adapter
Video Cable
 
						

							
 English

Connections

English 

Connecting audio from external Components
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital 
component.
 Press the FUNCTION button to select D. IN input.
The mode switches as follows : BD/DVD ; D. IN ; AUX ; R. iPod ; W. iPod ; HDMI1 ; HDMI2 ; TUNER
NOTE
To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
Connect AUX IN (Audio) on the product to the Audio Out of the external analogue component.
 Be sure to match connector colors.
 Press the FUNCTION button to select AUX input. 
The mode switches as follows : BD/DVD ; D. IN ; AUX ; R. iPod ; W. iPod ; HDMI1 ; HDMI2 ; TUNER
NOTE
  You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of 
the VCR to this product.
1.
2.
•
✎



1.
•
2.
•
✎

SYSTEM CABLE
ONLY FORUPDATEDIGITALAUDIO IN(OPTICAL)
HDMI OUTHDMI IN 1HDMI IN 2
FM ANT
AUX INSPEAKERS OUTFRONTFRONT
CENTER
WIRELESS
ASC IN
SPEAKER IMPEDANCE : 3
SYSTEM CABLE
ONLY FORUPDATE
HDMI OUTHDMI IN 1HDMI IN 2
FM ANT
SPEAKERS OUTFRONTFRONT
CENTER
WIRELESS
ASC IN
SPEAKER IMPEDANCE : 3SPEAKER IMPEDANCE : 3
DIGITAL
Optical Cable
(not supplied)
Audio Cable (not supplied)
If the external analogue 
component has only one 
Audio Out, connect either left 
or right.
Set-Top BoxVCR
White
Red
OPTICALAUX
 
						

							
 English
English 

02
Connections

Connecting to a network
You can connect this product to a network and use network based services such Smart Hub and BD-
LIVE (See pages 62~71), as well as receive software upgrades through the network connection. We 
recommend using a wireless router or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN 
terminal of your modem.
Set the network options. (See page 39)
NOTE
Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the 
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
DSL users, please use a router to make a network connection.
To use the AllShare function, you must connect your PC to the network as shown in the figure.
1.
2.
✎



DC 12ViPodSYSTEMCABLELAN
Router
Broadband modem
Broadbandservice
OrBroadband modem(with integrated router)
Broadbandservice
Networking with PC forAllShare function (See page 71)
 
						

							
 English

Connections
English 
Wireless Network
You can connect the home cinema to your network through a wireless IP sharer (router).
To set the network confi guration options. see page 39.
NOTE
To use a wireless network, your product must be connected to a wireless IP sharer (router). If the wireless IP sharer supports DHCP, your product can use a DHCP (dynamic) or static IP address to connect to the wireless network.
This product supports IEEE 802.11b,g and n. We recommend using IEEE 802.11n. When you play video over a IEEE 802.11b or g connection, the video may not play smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure.
If you select the Pure High-throughput (Greenfi eld) 802.11n mode and set your routers's Security Encryption type to WEP, TKIP or TKIPAES (WPS2Mixed), your Samsung home cinema will not support the connection in compliance with new Wi-Fi certifi cation specifi cations.
If your router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Confi guration) or PIN (Personal Identifi cation Number). WPS will automatically confi gure the SSID and WPA key in either mode.
You can set up the wireless network connection in three ways:- Using Auto Setup (the Auto Network Search function) through Wireless (General)- Using WPS(PBC)- Using One Foot Connection
Wireless LAN, by its nature, may cause interference, depending on the operating conditions. (router performance, distance, obstacles, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
The home cinema supports the following security protocols only:Authentication Mode : WEP, WPAPSK, WPA2PSK
Encryption Type : WEP, AES
To use the AllShare function, you must connect your PC to your network as shown in the fi gure.
The connection can be wired or wireless.
✎








1)
2)

Wireless IP sharer
Networking with PC for
AllShare function
(See page 71)
PC
Broadband
service
 
						

							
 English
English 

03
Setup
Initial Settings
Turn on your TV after connecting the product.When you connect and turn on the product to a TV for the fi rst time, the Initial Settings screen appears.
Initial Settings | On-Screen Language
m Move    " Enter    
Select a language for the on-screen displays.  Български  Hrvatski  Čeština  Dansk  Nederlands English  Eesti  Suomi  Français  Deutsch  Ελληνικά  Magyar  Indonesia  Italiano à´	¯
Press the ▲▼◄► buttons to select the desired language, and then press the ENTER button.
Press the ENTER button to select Start.
Press the ▲▼ buttons to select the desired TV Aspect Ratio, and then press the ENTER button. (See page 32)If you press the BLUE (D) button to skip Musical Auto Calibration or Network Setup, you can access the Home menu even if the Calibration or the Network Setup is not completed.
Plug the ASC microphone into the ASC IN jack on the product. (See page 36)
Press the ENTER button to select the Start button.Setting the Musical Auto Calibration function takes about 3 minutes.
Press the ▲▼ buttons to select the desired 
Network Settings : Wired, Wireless 
(General), WPS(PBC) or One Foot 
Connection, and then press the ENTER 
button. If you do not know the details of your 
Network Settings, press the BLUE (D) button 
on your remote instead to skip Network 
Settings here, fi nish the Initial Settings, and 
go to the Home menu.
If you selected a Network Settings, go to 
pages 39~42 for more information about the 
Network settings. When done, go to Step 8.
The Home menu appears. (For more 
information about the Home menu, please 
see page 30.)
1.
2.
3.
4.
5.
6.
7.
8.
Home Menu
 d WPS(PBC)
My DevicesInternetSettings
VideosPhotos
Music
My Contents
Function
 NOTE
The Home menu will not appear if you do not 
confi gure the initial settings except as noted 
below.
If you press the BLUE (D) button during the 
Musical Auto Calibration/network setup, you 
can access the Home menu even if the 
network setup is not completed yet.
If you want to display the Initial Setting screen 
again to make changes, select the Reset 
option. (See page 43)
If you use an HDMI cable to connect the 
product to an Anynet+(HDMI-CEC)-
compliant Samsung TV and 1.) You have set 
the Anynet+(HDMI-CEC) feature to On in 
both the TV and the product and 2.) You have 
set the TV to a language supported by the 
product, the product will select that language 
as the preferred language automatically.
If you leave the product in the stop mode for more than 5 minutes without using it, a screen saver will appear on your TV. If the product is left in the screen saver mode for more than 20 minutes, the power will automatically turn off.
•
✎





Setup
 
						

							
0 English

Setup

English 1

accessing the Settings menu
FUNCTIONTV SOURCEPOWER
BD RECEIVER/TVSLEEP
DISC MENUMENUTITLE MENU
MUTE
SFE MODE
DSP
VOLTUNING/CH
TOOLS
RETURNEXIT
INFO
ABCD
TUNER MEMORY
INIERNET 
MO/ST
REPEATFULL SCREEN
123
456
78
0
9
POPUP
@
DISC MENUTITLE MENU
TOOLSINFO
TUNER 
POPUP1
24
3
1MENU Button : Press to move to the Home menu.
2RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button :Move the cursor or select an item.Activate the currently selected item.Confi rm a setting.
4EXIT Button : Press to exit the current menu.
To access the Settings menu and sub-menus, 
follow these steps:
Press the POWER button.
The Home Menu appears.
Home Menu
d WPS(PBC)
My DevicesInternetSettings
VideosPhotos
Music
My Contents
5
6
2
4
3
Function1
1Selects My Devices.
2Selects Function.
3Selects My Contents.
4Selects Internet.
5Selects Settings.
6Displays the buttons available.
1.
•
Press the ◄► buttons to select Settings, 
and then press the ENTER button.
Press the ▲▼ buttons to select the desired 
submenu, and then press the ENTER 
button.
Press the ▲▼ buttons to select the desired 
item, and then press the ENTER button.
Press the EXIT button to exit the menu.
NOTE 
When the product is connected to a network, 
select Internet from the Home menu. 
Download the desired content from Samsung 
Apps. (See pages 69~71)
The access steps may differ depending on the 
menu you selected. 
The OSD (On Screen Display) may change in 
this product after you upgrade the software 
version.
2.
3.
4.
5.
✎