Home > Panasonic > All in One Printer > Panasonic Digital Color Imaging System DP-C106 Operating Instructions

Panasonic Digital Color Imaging System DP-C106 Operating Instructions

Here you can view all the pages of manual Panasonic Digital Color Imaging System DP-C106 Operating Instructions. The Panasonic manuals for All in One Printer are available online for free. You can easily download all the documents as PDF.

Page 111

Adjusting the Printer Color Problem Solving
99
2.  Gray Balance Page
The gray patch you select is used by the printer to balance all colors.
1. Press the ITEM/ENTER button. The PRINTING GRAY BALANCE
PAGE is displayed, and after a moment the page is delivered the
TopTray.
a.  Select the color patch that is most like the gray that surrounds the
color patches.
b.  Circle your selection.
2. BEST PATCH (ROW) is displayed on the Printer Control Panel.  Use the
(        ) ARROW buttons to enter the number of...

Page 112

Problem Solving Adjusting the Printer Color
100
3.  Comparison Page
The Comparison Page allows you to see the changes that you made during
the VisualCal adjustment.  On the page are four rows of color photographs.
The first row and the third row show the color setup before you selected
VisualCal.  Row two and row four show the color setup after the VisualCal
adjustment was completed.  Now you must decide which setup is preferred.
Perform one of the following steps:
• APPLY CHANGES YES is displayed on the...

Page 113

Printer Error Messages Problem Solving
101
Printer Error Messages
If the problem still exists after following the instructions in this table, call your
service support and report the problem.
Message Possible Cause Action
010-317 CALL FOR
SERVICEThere may be an
electrical problem.Call your service support and report
the code displayed in the message.
BLACK TONER
LOWThe Black Toner
Cartridge is low.When prompted, replace the Black
Toner Cartridge.
CHECK LOADING
OF [PAPER TRAY]
IN USEThe input document...

Page 114

Problem Solving Printer Error Messages
102
Message Possible Cause Action
CLOSE AREA 5 The Area 5 Access
Cover is open.Close the Area 5 Access Cover.
CLOSE DUPLEX
UNIT/KITThe Duplex Unit/Kit is
open.Close the Duplex Unit/Kit.
CLOSE FRONT
COVERThe Front Cover is open. Close the Front Cover.
CLOSE PAPER
TRAY 1Paper Tray 1 is open. Close the Paper Tray 1.
CLOSE PAPER
TRAY 2Paper Tray 2 is open. Close the Paper Tray 2.
CLOSE PAPER
TRAY 3Paper Tray 3 is open. Close the Paper Tray 3.
CYAN TONER
LOWThe Cyan...

Page 115

Printer Error Messages Problem Solving
103
Message Possible Cause Action
INSTALL YELLOW
TONER
CARTRIDGEThe Yellow Toner
Cartridge is emptyReplace the Yellow Toner Cartridge.
LOAD [STOCK
SIZE] IN TRAY 1Paper Tray 1 is low on
the specified stock.Fill the Paper Tray 1 with the
appropriate stock.
LOAD [STOCK
SIZE] IN TRAY 2Paper Tray 2 is low on
the specified stock.Fill the Paper Tray 2 with the
appropriate stock.
LOAD [STOCK
SIZE] IN TRAY 3Paper Tray 3 is low on
the specified stock.Fill the Paper Tray 3...

Page 116

Problem Solving Printer Error Messages
104 This page is intentionally left blank. 

Page 117

Printer Error Codes Problem Solving
105
Printer Error Codes
An Error Code may indicate that an electrical or mechanical problem exists in
the Printer.  Typical error codes, six digit numbers with a hyphen in the middle,
are followed by the words CALL FOR SERVICE.
If an Error Code should appear on the Printer Control Panel perform the
following steps:
1.  Write down the code number.
2.  Switch Off the Scanner power switch.
3. Wait 20 seconds.
4.  Switch On the Scanner power switch.
•  If the problem is...

Page 118

Problem Solving Printer Error Codes
106
This page is intentionally left blank. 

Page 119

Scanner Error Codes Problem Solving
107
Scanner Error Codes
An Error Code may indicate that an electrical or mechanical problem exists in
the Scanner.  Typical error codes, xx digit numbers, are followed by the words
CALL FOR SERVICE.
If an error code should appear on the Scanner Control Panel perform the
following steps:
1.  Write down the code number.
2.  Switch Off the Scanner power switch.
3. Wait 20 seconds.
4.  Switch On the Scanner power switch.
•  If the problem is resolved, resume printing or...

Page 120

Problem Solving Scanner Error Codes
108 This page is intentionally left blank. 
Start reading Panasonic Digital Color Imaging System DP-C106 Operating Instructions

Related Manuals for Panasonic Digital Color Imaging System DP-C106 Operating Instructions

All Panasonic manuals