Ricoh Aficio MP 9000 User Manual

							Interface Settings
53
2
❖IPv6 Stateless Address Autoconfiguration
You can set “IPv6 Stateless Address Autoconfiguration” to “Active” or “Inactive”.
Active
Inactive
❖DNS Configuration
Make settings for the DNS server.
When you select [Specify], enter the [DNS Server] IP address as “xxx.xxx.xxx.xxx(“x
indicates a number).
Auto-Obtain (DHCP)
Specify
 DNS Server 1: 000.000.000.000
 DNS Server 2: 000.000.000.000
 DNS Server 3: 000.000.000.000
❖DDNS Configuration
You can specify the DDNS settings.
Active
Inactive
❖Domain Name
You can specify the domain name.
Auto-Obtain (DHCP)
Specify
❖WINS Configuration
You can specify the WINS server settings.
If [On] is selected, enter the [WINS Server] IP address as “xxx.xxx.xxx.xxx(“x
indicates a number).
If DHCP is in use, specify the [Scope ID].
Enter a [Scope ID] using up to 31 alphanumeric characters.
On
 Primary WINS Server: 000.000.000.000
 Secondary WINS Server: 000.000.000.000
Scope ID
Off
❖Effective Protocol
Select the protocol to use in the network.
IPv4: Active / Inactive
 IPv6: Active / Inactive
NetWare: Active / Inactive
 NetBEUI: Active / Inactive
 AppleTalk: Active / Inactive
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
54
2
❖NCP Delivery Protocol
Select the protocol for NCP delivery.
IPX Priority
TCP/IP Priority
IPX Only
TCP/IP Only
❖NW Frame Type
Select the frame type when you use NetWare.
Auto Select
Ethernet II
 Ethernet 802.2
 Ethernet 802.3
 Ethernet SNAP
❖SMB Computer Name
Specify the SMB computer name.
Enter the computer name using up to 15 alphanumerical characters.
*+,/:;=?[\]|. and spaces cannot be entered.
Setting a computer name starting with RNP and rnp is inhibited.
Use uppercase letters for alphabet.
❖SMB Work Group
Specify the SMB work group.
Enter the computer name using up to 15 alphanumerical characters.
*+,/:;=?[\]|. and spaces cannot be entered.
Use uppercase letters for alphabet.
❖Ethernet Speed
Set the access speed for networks.
Select a speed that matches your network environment. [Auto Select] should
usually be selected.
Auto Select
 10Mbps Full Duplex
 10Mbps Half Duplex
 100Mbps Full Duplex
 100Mbps Half Duplex
Downloaded From ManualsPrinter.com Manuals 
						

							Interface Settings
55
2
❖LAN Type
When you have installed the optional IEEE 802.11b interface unit, select inter-
face, IEEE 802.11b (wireless LAN) or Ethernet.
Ethernet
 IEEE 802.11b
Appears when the optional IEEE 802.11b interface unit is installed.
If Ethernet and IEEE 802.11b (wireless LAN) are both connected to the ma-
chine, the selected interface takes precedence.
❖Ping Command
Check the network connection with ping command using given IP address.
If you fail to connect to the network, check the following, and then retry the
ping command.
 Check TCP/IP of the printer is active.
 Check that the machine with assigned IP address is connected to the net-
work.
 There is a possibility that same IP address is used for the specified equip-
ment.
❖Permit SNMPv3 Communication
Set the encrypted communication of SNMPv3.
 Encryption Only
Encryption/Clear Text
If you set to [Encryption Only], you need to set password for the machine.
❖Permit SSL/TLS Communication
Set the encrypted communication of SSL/TLS.
 Ciphertext Only
Ciphertext Priority
 Ciphertext/Clear Text
If you set to [Ciphertext Only], you need to install the server authentification for
the machine.
❖Host Name
Specify the host name.
Enter the host name using up to 63 alphanumerical characters.
❖Machine Name
Specify the machine name.
Enter the machine name using up to 31 alphanumerical characters.
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
56
2
Parallel Interface
This section describes various items of [Parallel Interface] under [Interface Settings].
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board (optional).
❖Parallel Timing
Sets the timing for the control signal of the parallel interface.
ACK outside
ACK inside
STB down
❖Parallel Communication Speed
Sets the communication speed for the parallel interface.
High Speed
Standard
❖Selection Signal Status
Sets the level for the select signal of the parallel interface.
High
Low
❖Input Prime
Sets whether to validate or invalidate the input prime signal upon receipt.
Active
Inactive
❖Bidirectional Communication
Sets the printers response mode to a status acquisition request when using a
parallel interface.
On
Off
When set to [Off], bidirectional communication function will be disabled. Al-
so, printer driver will not be installed under Windows Auto Detect function.
❖Signal Control
Sets procedure to error during printing.
Job Acceptance Priority
Printer Priority
Downloaded From ManualsPrinter.com Manuals 
						

							Interface Settings
57
2
IEEE 1394
This section describes various items of [IEEE 1394] under [Interface Settings].
[IEEE 1394] is displayed when this machine is installed with the IEEE 1394 inter-
face board (optional).
❖IPv4 Address
When you connect the machine to a network using the IEEE 1394 interface,
you must configure the IP address and subnet mask.
When you select [Specify], enter the [Machine IPv4 Address] and [Sub-net Mask]
as “xxx.xxx.xxx.xxx”(“x” indicates a number).
When you use the IEEE 1394 interface on a network, you cannot use the Eth-
ernet interface in the same domain. To use both interfaces in the same do-
main, set different values for the [Sub-net Mask].
If you use the interface for Ethernet and IEEE 1394 (IP over 1394) at the same
time, settings must be made carefully.
Auto-Obtain (DHCP)
Specify
 Machine IPv4 Address: 000.000.000.000
 Sub-net Mask: 000.000.000.000
❖DDNS Configuration
You can specify the DDNS settings.
Active
Inactive
❖Host Name
Specify the host name.
Enter the host name using up to 63 alphanumerical characters.
❖Domain Name
Make settings for the domain name.
Auto-Obtain (DHCP)
Specify
Enter the domain name using up to 63 alphanumerical characters.
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
58
2
❖WINS Configuration
You can specify the WINS server settings.
If [On] is selected, specify the [WINS Server] IP address as “xxx.xxx.xxx.xxx
(“xxx indicates a number).
If DHCP is in use, specify the [Scope ID].
Enter [Scope ID] using up to 31 alphanumeric characters.
On
 Primary WINS Server: 000.000.000.000
 Secondary WINS Server: 000.000.000.000
Scope ID
Off
❖IPv4 over 1394
When you use the IP over 1394 function of the IEEE 1394 interface to connect
the machine to the network, or you print from computer with the IP over 1394
driver, you must specify [Active] for [IP over 1394].
Active
Inactive
Printing with IP over 1394 is possible under Windows Me/XP and Windows
Server 2003.
❖SCSI print (SBP-2)
When you print using the SCSI print client function supported by Windows
2000/XP, or Windows Server 2003, you must set [SCSI print (SBP-2)].
Active
Inactive
❖Bidirectional SCSI print
Specifies the printers response mode etc. for status requests when using the
IEEE 1394 interface.
On
Off
If this is set to [Off] bidirectional communication will not work.
Downloaded From ManualsPrinter.com Manuals 
						

							Interface Settings
59
2
IEEE 802.11b
This section describes various items of [IEEE 802.11b] under [Interface Settings].
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board (optional).
Implement respective settings simultaneously.
❖Communication Mode
Be sure to make all settings simultaneously.
 802.11 Ad-hoc
Ad-hoc
 Infrastructure
❖SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
ad-hoc mode.
The characters that can be used are ASCII 0x20-0x7e (32 bytes).
If blank is specified in 802.11b ad-hoc mode or ad-hoc mode, “ASSID ap-
pears.
❖Channel
Specifies a channel when you select 802.11b ad-hoc mode or ad-hoc mode.
The following channels are available:
Metric version: 1-14
 Inch version: 1-11
❖Security Method
Specifies the encryption of the IEEE 802.11b (wireless LAN).
If set to [WEP], always enter WEP key. If set to [WPA], set encryption method
and authentication method.
You can specify “WPA”, if you set [Communication Mode] to [Infrastructure].
Off
WEP
WPA
 WPA Encryption Method
Select either TKIP or CCMP(AES).
 WPA Authent. Method
Select either WPA-PSK or WPA802.1X). If you have selected “WPA-
PSK”, enter the pre-shared key (PSK) of 8- 63 characters in ASCII code.
❖Wireless LAN Signal
Shows the radio wave conditions of the access point connected in infrastruc-
ture mode.
Radio wave status is displayed when you press [Wireless LAN Signal].
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
60
2
❖Transmission Speed
Specifies the communication speed of the IEEE 802.11b (wireless LAN).
Auto Select
 11Mbps Fixed
 5.5Mbps Fixed
2Mbps Fixed
1Mbps Fixed
❖Restore Factory Defaults
You can return the IEEE 802.11b (wireless LAN) settings to their defaults.
No
Yes
Print List
You can check items related to the network in use.
The configuration page shows the current network settings and network infor-
mation.
APress [System Settings].
BPress [Interface Settings].
CPress [Print List].
Downloaded From ManualsPrinter.com Manuals 
						

							Interface Settings
61
2
DPress the {Start} key.
The configuration page is printed.
EPress [Exit].
FPress the {User Tools} key.
Note
❒You can also exit by pressing [Exit] on the User Tools main menu.
Downloaded From ManualsPrinter.com Manuals 
						

							System Settings
62
2File Transfer
This section describes various items of [File Transfer] under [System Settings].
❖Delivery Option
Enables or disables sending stored or scanned documents to ScanRouter V2
delivery server.
On
 Main Delivery Server IPv4 Address: 000.000.000.000
 Sub Delivery Server IPv4 Address: 000.000.000.000
Off
Set this option when specifying whether or not to use ScanRouter V2. If you
do, you will have to re-register I/O devices in ScanRouter V2.
❖Capture Server IP Address
Specify the capture server IP address.
This setting appears when the media link board is installed, and that the cap-
ture function is being used by the ScanRouter V2.
❖SMTP Server
If DNS is in use, enter the host name.
If DNS is not in use, enter the SMTP server IP address.
Server Name
Port No.
Enter the [Server Name] using up to 127 alphanumeric characters. Spaces can-
not be used.
Enter [Port No.] between 1 and 65535 using the number keys, and then press
the {#} key.
The Port No. is set to 25 by default.
Downloaded From ManualsPrinter.com Manuals