Toshiba Perception Electronic Business Communications System Installation And Maintenance Manual

							NOTES: 
I. XX = List Number. 
00 = System List (90 numbers maximum). 
0 1 I-W 25 = Station Lists (10 numbers each maximum). 
2. Input procedure is: 
Address Code-Space-Access Code-Pause- DN 
For example: 0 I 9 * NPANNXXXX 
3. Stored numbers may be any length between I and ?6 digits; 
” * ” enters a 3second pause and is 
counted as one of the 16 digits. 
4. If the List Number (LNO) was 00 (System List), 2-d&it address codes will be used (10 Q 99). 
5. No further prompt will be given until [DELI is entered. 
6. [CTRL.l [Xl = Ignore line entered 
[CTRLI iHI = Backspace 
[DELI = Stop printing and return to REQ 
L’DELJ [DELj = Abort program 
OT system ki our ot range 
is allow1 
coae of station list is out of range (O-9 is allowed). 
DN (1 AJ 16 digits are allowed).  1 ERSDL 03 1 invalid 
ata 
Authorization Procedure must be complete 
If an “OK” response is received, proceed 
as follows: 
NOTES: 
1. SPCC I & SPCC 2 entries are the DN of any Specialized Common Carrier (SPCC) usad {MCI, 
SPC, etc.). 
2. Enter the trunk group number and type of calls to be recorded on this Trunk Group: 
NONE 
INC - Incoming Only 
OGT - Outgoing OnJy 
IA0 - Incoming and Outgoing 
TOL - Toll Only 
INT - Incoming - all 
- Outgoing - toll only 
3. TGP continues 
to be prompted until [DEL] is entered. 
4. [CTRLI [Xl = Ignore line entered 
[C TR Ll [HI = Rackspace 
[DELJ = Stop printing and return to REQ 
[DELJ [DELJ = Abort program  
						

							be coinpleted. if art “Cl , proceecl 
NOTES: 
f. XX = Access Code of the Page Zone or Ail Page. 
2. [CTR L J [XJ = Ignore line entered 
[CTRLJ 
LHJ = Backspace 
[DELJ = Stop printing and return to R.EQ 
[DELJ [DELJ =&OH program 
ERATT 08 
Input data erased because program aborted during NEW data entry. 
ERATT 09 1 Attendant data not assigned to input port (REQ = CHG, OUT).  
						

							Procedure - Traffic Measurement 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
ITEM PROMPT 
I USER ENTRY 
OK 
1 DTRF 
- DISK LOADlN6 - 
REQ 
RPT, STT, CHG, OUT 
SYST.DATE MMDDYY 
MMDDYY or [CR] 
SYST.TlME HHMMSS 
HHMMSS or [CR] 
SCH J‘xxxr’ 
30,60, CMD, NONE or [CR] 
STR.DATE MMDDYY 
MMDDYY or [CR] 
STR.TiME HHMM 
HHMM or [CR] 
RPT 
SYST 
Y or N 
ATT0 
Y or N 
ATT1 
Y or N 
TGPOOwTGPl5 Y or N 1 NOTE 
1 
2 
3 
4 
5 
6 
7 
NOTES: 
1. RPT = Report Command-if the program had been started previously, a report would follow. 
See Table M- 1 for format. 
STT = Start Command-used to initialize the program and start the record keeping reporting 
activity. 
CHG = Change Command-used to alter reporting parameters. 
OUT = Out Command-used to stop reports. 
2. System outputs the date in its memory (Month, Day, Year). An entry (MMDDYY) will over- 
write the existing data. A [CR] = no change. 
3. System outputs the time in its memory (Hours, Minutes, Seconds). An entry (HHMMSS) will 
overwrite the existing data, A [CR] = no change. 
4. Schedule of Reports: 
30 = Report every 30 minutes beginning at the time listed as STR. DA TE (Note 5) and STR. TIME 
(Note 6). 
60 = Report every 60 minutes beginning at the time listed as STR.DA TE (Note 5) and STR. TIME 
(Note 6). 
5. Date that record keeping and reporting should start. The system outputs the date in its memory 
(Month, Day, Year). An entry (MMDDYY) will overwrite the existing data. A [CR] = no change. 
6. Time that record keeping and reporting should start. The system outputs the time in itsmemory 
(Hours& Minutes). An entry (HHMM) will overwrite the existing data. A [CR] = no change. 
7. Enter Y (yes) or N (no) followed by a [CR] to select the parameters to be reported (see Table 
M-2). 
8. [CTRL] [XJ = Ignore line entered 
[CTR Ll [HI = Backspace 
[DELI = Stop printing and return to REQ 
[DEL.J[DEL] = Abortprogram  
						

							-3 - 
ITEM 
Authorization Procedure 1 PROMPT 1 USER ENTRY 
OK 
1 TRF 
- DISK LOADING - 
REQ 
RPT 
RPT FROM 
MM DD YY 
HH MM SS 
TO MM DD YY 
HH MM SS 
SYST RCV R DLY 0000 
ATT 0 IN SVC 0000 
WK TIM 0000 
INC TRK 0000 
INC TIM 0000 
0 CALL 0000 
LPS BSY 0000 
TTA 0000 
OVFL 0000 
ATT 1 
(SAME AS ATT 0) 
TRUNKS 
TGP OO* 
INC USE 0000 
INC CALL 0000 
O.G. USE 0000 
O.G. CALL 0000 
ATB 0000 
GROUP 
System 
Attendant #0 ITEM IME 
DTMF RCVR Delay (3 sec.) 
Time in Service TYPE OF ~~ASU~~M~~~ 
Peg Count 
ccs 
Work Time 
ccs 
Incoming (Trunk) Calls Peg Count 
Time Servicing Incoming Calls 
ccs 
Dial “0” Calls 
Peg Count 
All Loops Busy 
Peg Count 
Average Time to Answer SEC 
Overflow 
Peg Count 
Attendant #I 
(Same as Attendant #O) 
Trunks Group 00* 
Incoming Usage ccs 
incoming Calls Peg Count 
Outgoing Usage ccs 
Outgoing Calls Peg Count 
Ail Trunks Busy Peg Count 
*Trunk Groups 01 AJ 15 are reported in the same way as Group 00. 
Program Name: Traffic Measurement (DTRF) 
Error Code Meaning 
ERTRF 01 Program has already been started. Either the START TIME has been 
reached or STT was entered previously. (R EQ = STT) 
ERTRF 02 Invalid response. STT or RPT was entered in response to REQ but 
the SCH entry is 30,60 or NONE. 
ERTRF 03 RPT was entered in response to REQ but the program has not been 
started. (Correct START TIME & DATE, or enter: STT)  
						

							Procedure - DTM F Receiver 
Authorization Procedure 
as follows: Data Block 
must be completed. If an “OK” response is received, proceed 
ITEM 
Port Number PROMPT 1 USER ENTRY NOTE 
OK ] DRCV 
- DISK LOAQING - 
REQ NEW, OUT 
POR ROOX 1 
REQ 
NOTES: 
I. Enter the RCVR port number (ROO = PCB number, X = Circuit number). 
2. [CTRLI 
[Xl = ignore line entered 
[CTRLJ [HI = Backspace 
[DEL] = Stop printing and return to REQ 
[DEL] [DEL] = Abort program 
Error Codes 
No PCB is equipped in that location. 
Authorization Procedure must be completed, If an “OK” response is received, proceed 
as follows: 
ITEM 
Trunk Group Number 
Tenant Number 
Trunk Type 
lncoming/Outgoint 
Advance Step 
Access Code 
Class of Service 
Transmission 
Start Arrangement 
Warning Tone Allowed? 
Outgoing Absorb Digits 
Incoming Absorb Digits 
Digits Inserted Incoming 
Toll Allowed? 
Code Restriction Lists 1 PROMPT 1 USER ENTRY 1 NOTE 
OK 1 DTGP 
- QISK LOADING - 
REQ 
NEW, CHG, OUT 
GRP Owl5orPVL I 
TEN Oor I 
TKT COT,FEX,DlD,PVL,CSA,TlE,WAT 2 
IA0 ICT, OGT, IA0 
STP XX or NONE 
3 
COD N (NN or NNN) 
cos Owl5 4 
TRN NTC, TRC, VNL 
STR IMM, WNK, DDL 
WTA Y or N 
OAB 5 
IAB 6 
INS 7 
TOL Y or N 
CRL 
Ow7orNONE 8  
						

							NOTES: 
1. A maximum of 16 Trunk Groups (normally 0 w 15) are possible. If Private Lines are to be equip- 
ped, the code “PVL ” is used in place of 15. 
2. TKT cannot be changed, Data Block must be removed (OUT) and NEW data entered. 
3. XX = Trunk Group to be stepped to if this group is busy. 
4. COS is meaningful only for TiE/CCSA/DlD Trunks. 16 COS groups are provided and are defined 
in the Class of Service Data Block. 
5. List the digit which is to be ignored for the purpose of Toll/Code Restriction. This digit will 
be outpulsed but not counted as the first digit. 
6. Enter the number of digits which are to be stripped from an incoming dialed DN (TIE, DID, 
or CCSA Trunk). 
Example: fAB = I 
Incoming DN = 8249 
Recognized DN = 249 
7. Enter the digits (maximum 2) which must be prefixed to an incoming dialed DN after Incoming 
Absorb Digit. 
Example: INS = 52 
IAB = I 
lncom ing DN = 327 
Recognized DN = 5227 
8. Enter the CRL (Code Restriction List) number of each list that must be checked when a Toll 
Denied station is making a call. System maximum is 8 (lists 0 ti 7). 
9. [CTRL] [X] = Ignore line entered 
[CTR L] [f-l] = Backspace 
[DEL] = Stop printing and return to REQ 
[DELI [DELI = Abort program 
TRUNK TYPES 
ICOT 1 FEX 1 iMAT PVL 1 DID 1 CSA 1 TIE 
cos 0 0 0 0 x x x 
TRN X X X X X X X 
STR X X X X X X X  
						

							rror Codes 
Program Name: Trunk Group Data Block (DTGP) 
Error Code 1 Meaning 
ERTRG 00 1 
ERTRG 01 GRP still has trunk assigned (REQ = OUT). 
ERTRG 02 The entered GRP number is already assigned (REQ= NEW). 
ERTRG 03 One or more trunks are busv (REQ = CHG). 
ERTRG 04 The entered GRP number dkei not exist (iEQ = CHG). 
ERTRG 05 Entered advance step GRP is the same as this GRP number. 
ERTRG 06 
ERTRG 07 
ERTRG 08 #I entered but tenant service not enabled in System Data Block. 
ERTRG 09 #I entered but Attendant Console #I does not exist. 
ERTRG IO Start arrangement conflicts with trunk type. 
ERTRG II WTA = Y was entered but trunk type is PAG. 
ERTRG 12 IA0 = ICT was entered but trunk type is PAG. 
ERTRG 13 The entered GRP number does not exist (REQ = OUT). 
ERTRG 14 Access code conflicts with an existing number. 
ERTRG 15 Input data erased because program aborted during new mode. 
Non-transmission Transmission 
Attendant Lines 
c 2dB loss and 
not impendance 
Station Lines/ 
Attendant Lines 
(2-wire facility < 2dB loss 
or 4-wire facility) 
NOTE: 
The numbers in the boxes represent actual through connection loss in c/B.  
						

							Procedure - Trunk Data Block 
Authorization Procedure must be completed. if an “OK” response is received, proceed 
as follows: 
ITEM 
Port Number 
Group/Member Number 
Trunk DN 
Night Number 
Signalling 
Disconnect Supervision? 
Control of Disconnect 
incoming Dialing 
Dialing Outgoing 
Answer Supervision 1 PROMPT 1 
USER ENTRY 
OK 1 DTRK 
- DISK LOAQING - 
REQ 
NEW, CHG, OUT 
POR TNNX 
GMN YYZZ 
TDN BBB 
NIT NNN, NONE (UNA) 
SIG GRD, LOP, EAM, LDR, OAD 
DIS Y or N 
CTL 
OPC, FPR 
DIN 
DIP, TON 
DOT 
PI 0, P20, TON 
ANS 
Y or N 
1 NOTE 
I 
2&3 
4 
5 
6 
7 
8 
9 
8&10 
NOTES: 
I. 
2. 
3. 
4. 
5. 
6. 
7. 
8. 
9. 
IO. 
1 I. 
N/V = Trunk PC5 number, X = Circujt number. 
YY = Trunk Group Number (0 w 15 or PVL). 
GMN cannot be changed, Data Block must be removed (OUT) and NEW data entered. 
This prompt is valid only for TGP PVL. TDN is the DN assigned to a private trunk line. 
NNN is the trunk% Night station. This number can also be changed by the Attendant when making 
night assignments (no meaning for TlE/CCSA/DlD trunks). 
Y or N tells the system if Disconnect Supervision can be expected from the distant end. 
OPC = Originating Party Control, FPR = First Party Release. 
Has meaning only for TlE/CCSA/DlD Trunks. 
Outgoing dialing method: 
PI0 = Rotary Dial IO PPS 
P20 = Rotary Dial 20 PPS 
TON= DTMF 
Is Answer Supervision required to the calling party? 
[CTR L] [X] = Ignore line entered 
[CTRL] [H] = 5ackspace 
[DELI = Stop printing and return to REQ 
[DELI [DELI = Abort program 
TRUNK TYPES 
X = Used, 0 = Not Used  
						

							Error Codes 
Program Name: Trunk Data Block (DTRK) 
Error Code 1 Meanina 
ERTRK 01 1 PCB is not trunk type. 
ERTRK 02 1 Port is busy (REQ = OUT).  ERTRK 00 1 No PCB is equipped in that location. 
ERTRK 03 1 Port is alreadv assianed fRE0 = NFW) I 
ERTRK 04 1 Trunk Group Data Block does not exist. 
ERTRK 05 / Member number already assigned. 
ERTRK 06 1 Entry conflicts with existing DN or TDN 
ERTRK 07 1 Entered night number does not yet exist. 
1 ERTRK 08 
ERTRK 09 Type of signalling entered conflicts with the trunk type. 
ERTRK 10 
ERTRK 11 Input data erased because program aborted during NEW mode. 
ERTRK 12 The port is not assigned. 
ERTRK 13 Another type of data is already assigned to the input port. 
ERTRK 14 
ERTRK 15 Entered DN already assigned to station (EKT or STT). 
ERTRK 16 Entered DN already assigned to another trunk. 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
iTEM 
1 PROMPT 
USER ~~~~Y 1 NOTE 
Ol< PSYS 
REQ 
NOTE I-The following responses are possible: 
PRT = Output System Data Block 
KTRL] [Xl = ignore line entered 
[CTRLI 
[HI = backspace 
[DELI = Stop printing and return to REQ 
[DELI [DELI = Abort program 
as follows: pleted. If an “OK” response is received, proceed 
NOTE I-The following responses are possible: 
PRT = Output System Data Block 
[CTRL] [Xl = Ignore line entered 
[CTRLI [HI = Backspace 
[DELI = Stop printing and return to REQ 
[DEL.l [DEL] = Abort program  
						

							Procedure - Print Station Data Block 
Authorization Procedure must be completed. If an “OK” response is received, proceed 
as follows: 
f-?-EM PROMPT 1 USER ENTRY 1 NOTE 
I 
OK 
1 PSDf3 
I 
- DISK LOADING - 
REQ 
I I 1 
- EXECUTE - 
REQ 
I I I 
NOTE I- The folio wing responses are possible: 
PORALL = All SDBs will be output in numerical order of ports (lowest first) 
PORNNX = Port NNX data will be output 
POR VAC = A list of all unassigned ports will be output 
DNALL = All SDBs will be output in numerical order (lowest first) by DN (PDN for EKTs) 
DNNN = DN NNN data will be output; if it is a multiple appearance DN, all Data Blocks 
it appears in will be output 
EKTAL L = All EKT SDBs will be output in order of PDN (lowest first) 
STTALL. = All standard telephone Data Blocks ~$1 be output in order of DN (lowest first) 
[CTRL] [Xl = Ignore line entered 
[CTR Ll [H] = Backspace 
[DEL] = Stop printing and return to REQ 
[DELI [DELI = Abort program 
Program Name: Print Station Data Block (PSDB) 
Error Code Meaning 
ERPST 00 Input PCB number or Circuit number is out of range. 
ERPST 01 Input DN does not exist. 
ERPST 02 Input port is not assigned to EKT or 500/2500. 
ERPST 03 Manual signalling port does not exist. 
Authorization Procedure must be completed. If an “OK” response is r~cz&A, proceed 
as follows: 
ITEM PROMPT 1 USER ENTRY NOTE 
I 
OK 
1 PCOS 
- DISK LOADING - 
REQ 
I I - EXECUTE - 
REQ I 
NOTE I-The following responses are possible: 
PRT = COS Data Block will be output 
[CTRLI [XI = Ignore line entered 
[CTRLI [HI = Backspace 
[DEL] = Stop printing and return to REQ 
[DEL] [DELI = Abort program