Acer Aspire 6930 6930G User Manual

							Chapter 371
5.Grasp the Subwoofer Module from the RIGHT side as shown and tilt over and to the left, as shown.
NOTE: The Subwoofer Module is not a replacable part. Do NOT remove from the computer.
6.Grasp the Speaker Module by the right side and tilt up to remove.
Removing the Antenna Cables
1.Remove the Lower Cover. See “Removing the Lower Covers” on page 53.
1.Remove the Speaker Module. See “Removing the Speaker Module” on page 70.
2.Turn the computer upside down, and disconnect the Antenna Cables from the WLAN module.
Lift to expose the 
Speaker Cable. 
						

							72Chapter 3
3.Pull back the cables away and out of the housing well.
4.Turn the computer over (upper base facing up) to expose the Antenna cables.
5.After removing the Speaker Modules, grasp the Antenna cables sitting underneath. Pull through.
6.Continue to remove the cables until they are completely out of the housing well.
NOTE: Place the cables to one side to avoid damage. 
						

							Chapter 373
Removing the LCD Module
1.Disconnect the Antenna cables. See “Removing the Antenna Cables” on page 71.
2.Disconnect the LCD and Power cables.
3.Remove the four securing screws (two on each hinge) from the LCD hinges.
StepSizeQuantityScrew Type
LCD Module M2.5*5-I 
(BNI)(NYLOK)4 
						

							74Chapter 3
4.Carefully remove the LCD module from the chassis.
 Removing the Upper Base
1.Remove the LCD module. See “Removing the LCD Module” on page 73.
2.Turn the computer over. Remove the ten screws on the bottom panel.
 
StepSizeQuantityScrew Type
Upper Cover
(Red call out)M2.0*3.0-I-NI-NYLOK 2
Upper Cover
(Blue call out)M2.5*6.5-I 
(BZN(NYLOK-RED)11 
						

							Chapter 375
3.Turn the computer over and disconnect the three FFC cables from the mainboard.
Unlock the connector and disconnect A as shown. Unlock the connector and disconnect B as shown.
Unlock the connector and disconnect C as shown.
 
B
C
A 
						

							76Chapter 3
4.Remove the ten securing screws on the top panel.
 
WARNING:Care must be taken when removing the Upper Base from the Lower Base to prevent damage or 
stress to the surface.
5.Grasp the upper base by the sides and gently lift to remove.
StepSizeQuantityScrew Type
Upper Cover M2.5*6.5-I 
(BZN(NYLOK-RED)10 
						

							Chapter 377
Removing the Finger Print Reader
1.Remove the Upper Base. See “Removing the Upper Base” on page 74.
2.Unlock the securing latch and disconnect the Touch Pad FFC.
3.Unlock the securing latch and disconnect the Finger Print Reader FFC.
4.Remove the three securing screws.
StepSizeQuantityScrew Type
Finger Print 
ReaderM2.0*3.0-I-NI-NYLOK 3 
						

							78Chapter 3
5.Using your fingers, gently lift the Finger Print Reader board from the Upper Base.
Removing the USB Board
1.Remove the Upper Base. See “Removing the Upper Base” on page 74.
2.Grasp the cable connector and pull to remove from the bottom base.
3.Remove the single securing screw from the USB board.
StepSizeQuantityScrew Type
USB Board M2.0*3.0-I (BKAG) 
(NYLOK) IRON1 
						

							Chapter 379
4.Hold the USB board by the edges and pull up to remove.
Removing the Modem Module
1.Remove the Upper Base. See “Removing the Upper Base” on page 74.
2.Disconnect the RJ-11 cable from the modem as shown.
3.Remove the two (2) securing screws.
StepSizeQuantityScrew Type
Modem Module M2.0*3.0-I-NI-NYLOK 2 
						

							80Chapter 3
4.Lift the module and remove from the lower cover as shown.
Removing the Bluetooth Module
1.Remove the Modem Module. See “Removing the Modem Module” on page 79.
2.Grasp the cable as shown and pull to disconnect from the Bluetooth module.
3.Remove the single securing screw.
StepSizeQuantityScrew Type
Bluetooth Module M2.0*3.0-I-NI-NYLOK 1