Canon printer FAXPHONE L75 User Manual

							Chapter 3 Registering Information3-9
Registering
Information
Setting the Daylight Saving Time
This machine supports the daylight saving time system that shifts the clock time ahead
or back according to the change in seasons. You can select whether the time
information in your machine changes to match the daylight saving time system and set
the day and time when the daylight saving time starts and ends.
1Open the one-touch speed dialing panel.
2Press Data Registration.
3Press Set.
4Use ∂or ¨to select SYSTEM 
SETTINGS
.
5Press Set.
6Use ∂or ¨to select DAYLGHT SAV TIME.
7Press Set.
8Use ∂or ¨to select the setting you want.
•You can select from the following:
–
ON
Enables the daylight saving time.
–OFF
Disables the daylight saving time.
■If you selected OFFin step 8:
9Press Set.
10Press Stopto return to standby mode.12/27 FaxTel
TEL REGISTRATION
ON
ON
DAYLGHT SAVTIME
RX RESTRICTION
SYSTEM SETTINGS
USER SETTINGS
DATA REGSTRATION 
						

							3-10Registering Information Chapter 3
■If you selected ONin step 8:
9Press Setto register your selection.
10Press Setto select START DATE/TIME.
11Press Set and press ∂or ¨to select the month 
when the daylight saving time starts, and press 
Setto register your selection.
n
If you want to change your selection after pressing Set, press ¨to return to your previous
selection, make the necessary changes and press 
Set.
12Press Set and press ∂or ¨to select the week
when the daylight saving time starts, and press 
Set
register your selection.
•You can select from the following:
–
FIRST WEEK
–SECOND WEEK
–THIRD WEEK
–FOURTH WEEK
–LAST WEEK(fifth week)
13Press Set and press ∂or ¨to select the day 
of the week when the daylight saving time starts, 
and press 
Setto register your selection.
14Press Set and use the numeric buttons to 
enter the time when the daylight saving time 
compensation is made, and press 
Setto 
register your selection.
•Use the 24-hour format for the time 
(e.g. 2:00 p.m. as 14:00) and 
precede single digits with a zero.
n
If you make a mistake while entering the time, press Clearunder the one-touch speed dialing
panel to clear your entry and enter the correct time. You can also use ¬
or ®to move the cursor
under the incorrect number and enter the correct number.
02:00
02:00
TIME
SUNDAY
SUNDAY
DAY
FIRST WEEK
FIRST WEEK
WEEK
APRIL
APRIL
MONTH
START DATE/TIME 
						

							Chapter 3 Registering Information3-11
Registering
Information
15Press Setto select END DATE/TIME.
16Press Setand use ∂or ¨to select the
month, week, day of the week, and 
time when the daylight saving time
ends, as in steps 11 to 14 for the START 
DATE/TIMEsettings. (e.g.OCTOBER 
LAST WEEK, SUNDAYand 02:00)
17Press Stopto return to standby mode.12/27 FaxTel
OCTOBER
MONTH
END DATE/TIME 
						

							3-12Registering Information Chapter 3 
						

							Chapter 4 Document Handling4-1
Document
Handling
Chapter 4
Document Handling
This chapter describes the documents you can load in your machine for sending and
copying.
Document Requirements.........................................................................4-2
Scanned Area of a Document ................................................................4-2
Loading Documents.................................................................................4-3
Adding Pages to the Document in the ADF ...........................................4-4 
						

							4-2Document Handling Chapter 4
Document Requirements
The documents you load in the ADF for sending and copying must meet the following
requirements:
One-page document Multipage document of the 
same thickness and weight
SizeMin. 5.8 ¥4.1 in. (Min. 148 ¥105 mm) Min. 5.8 ¥4.1 in. (Min. 148 ¥105 mm)
(W ¥L)
Max. 8.5 ¥Approx. 39.4 in. Max. 8.5 ¥14 in.
(Max. 216 mm ¥Approx. 1 m) (Max. 216 ¥356 mm)
Quantity1 sheet Max. 30 letter- or A4-size sheets*
Max. 10 legal-size sheets*
Thickness0.002 to 0.009 in. (0.06 to 0.23 mm) 0.002 to 0.005 in. (0.06 to 0.13 mm)
Weight9.3 to 64 lb. (35 to 240 g/m2)10.7 to 24 lb. (40 to 90 g/m2)

Problem Documents
•To prevent document jams in the ADF, do not use any of the following:
–Wrinkled or creased paper – Carbon paper or carbon-backed paper
–Curled or rolled paper – Coated paper
–Torn paper – Onion skin or thin paper
•Remove all fasteners (staples, paper clips, etc.) before loading the document in the ADF.
•Make sure any glue, ink, or correction fluid on the document is completely dry before
loading it in the ADF.
•If you have a document that will not feed properly in the ADF, make a photocopy of
the document and load the copy instead.
•If you will be sending a document that you have printed from your machine, be sure to
use face-down delivery when printing that document (1p. 5-7).
Scanned Area of a Document
The shaded area shows the scanned
area of a document. Make sure your
document’s text and graphics fall within
this area.MAX. 0.16
(MAX. 4 mm)
MAX. 0.16
(MAX. 4 mm)
MAX. 0.12
(MAX. 3.0 mm) MAX. 0.12
(MAX. 3.0 mm)
Letter/Legal
*20 lb. (75 g/m2) paper 
						

							Chapter 4 Document Handling4-3
Document
Handling
Loading Documents
Insert the top of your document, face  
down, into the ADF until you hear a beep 
q.
Then adjust the document guides to the 
width of the document 
w.
•Tap multipage documents on a flat surface to
even the edges before inserting them in the
ADF.
The document is now ready for scanning.
n
•For a multipage document, the pages are fed one by one from the bottom of the stack.
•Wait until all pages of your document have been scanned before starting a new job.
■Problems With Multipage Documents
If you have trouble feeding multipage documents in the ADF, remove the stack and tap
it on a flat surface to even the edges. Then “slant” the stack so that its front edge is
bevelled, and insert the stack in the ADF.
n
To avoid feeding problems, make sure the document meets the document requirements
(
1p.4-2).
1
2
2 
						

							4-4Document Handling Chapter 4
Adding Pages to the Document in the ADF
If you need to add pages to your document in the ADF, wait until the last page starts
feeding, then load up to 30 additional pages (10 legal size). The last and first page
should overlap by about one inch (2.5 cm).
1 
(2.5 cm) 
						

							Chapter 5 Print Media Handling5-1
Print Media
Handling
Chapter 5
Print Media Handling
This chapter describes the print media you can load in your machine, and other
information related to print media and printing.
Print Media Requirements.......................................................................5-2
Printable Areas .......................................................................................5-3
Selecting and Loading Print Media.........................................................5-4
Paper ......................................................................................................5-4
Envelopes ...............................................................................................5-4
Transparencies .......................................................................................5-6
Selecting Face-Up or Face-Down Delivery............................................5-7
Changing the Paper Size Setting............................................................5-9
Adjusting the Toner Saver Setting........................................................5-11 
						

							5-2Print Media Handling Chapter 5
Print Media Requirements
You can load the following print media in the multi-purpose tray:
Once you have decided which paper you want to load, be sure to do the following:
•Check that the print media is compatible with your machine (1
p. 5-4).
•If you are loading paper, check that the paper size setting of the multi-purpose tray is
set for the paper size you are loading (1
p.5-9). (The default setting is letter size.)
•Check that paper delivery is set correctly for the print media and task you are
performing (1
p. 5-7).
•Check that you have loaded the print media correctly in the multi-purpose tray 
(1
p. 5-4).
3.6 ¥5 in.
(92 ¥
127 mm)
8.5 ¥
14 in.
(216 ¥356 mm)
8.5 ¥
11 in.
(216 ¥279 mm)
8.5 ¥
14 in.
(216 ¥356 mm)
8.3 ¥
11.7 in.
(210 ¥297 mm)
8.5 ¥
12.5 in. to 
8.5 ¥
13.4 in.
(216 ¥
317 mm to 
216 ¥340 mm)*
8.5 ¥
10 in. to 
8.5 ¥
11.2 in.
(216 ¥
254 mm to 
216 ¥285 mm)*
9.5 ¥
4.1 in.
(241 ¥104 mm)
8.7 ¥
4.3 in.
(220 ¥110 mm)
8.5 ¥
11 in.
(216 ¥279 mm)
8.3 ¥
11.7 in.
(210 ¥297 mm)
Quantity & Weight
Quantity:
Max. stack height:
0.4 in./10 mm 
(Approx. 100 sheets of 
20 lb. (75 g/m
2) paper)
Weight:
17 to 24 lb. (64–90 g/m2)
1 sheet: 17 to 28 lb.
(64–105 g/m
2)
7 envelopes
1 sheet
Size (W ¥L)
Min.
Max.
LT R(Letter)
LGL(Legal)
A4
CUSTOM1/LONG*
CUSTOM2/SHORT*
U.S.Commercial 
No. 10
European DL
LT R(Letter)
A4
Print Media
Plain Paper
Envelopes
Transparencies
*For this setting, you may need to load fewer sheets.