Garmin G1000 Manual

							190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 850227
FLIGHT MANAGEMENT
DEPARTURE (DP)
A Departure Procedure (DP) is loaded at the departure airport in the flight plan. Only one departure can 
be loaded at a time in a flight plan. The route is defined by selection of a departure, the transition waypoints, 
and a runway.
Figure 5-68  Departure Loading Page - Selecting the Departure
Departure Airport
Selected 
Departure
Departures Available at 
KMCI
Departure Waypoint 
SequencePreview of  Selected 
Departure
Loading a departure procedure into a stored flight plan:
1) Select a stored flight plan from the Flight Plan Catalog Page.
2) Select the EDIT Softkey; or press the MENU Key, select ‘Edit Flight Plan’, and press the ENT Key.  The Stored 
Flight Plan Page is displayed.
3) Select the LD DP Softkey; or press the MENU Key, select “Load Departure”, and press the ENT Key.  The 
Departure Loading Page is displayed.
4) Select a departure.  Press the ENT Key.
5) Select a runway served by the selected departure, if required.  Press the ENT Key.
6) Select a transition for the selected departure.  Press the ENT Key.
7) Press the ENT Key to load the selected departure procedure.  
						

							Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A228
FLIGHT MANAGEMENT
Figure 5-69  Departure Loading Page - Selecting Transition
Departure Airport
Selected 
Departure
Departure Transition Points 
Available
Selected Runway
Selected 
Departure End  Point
Preview ofSelected 
DepartureSelected Transition
Figure 5-70  Stored Flight Plan Page - Departure Inserted Inserted Departure Header
 - Departure Identifier: [departure
    airport]-[departure runway].
    [departure transition].
    [departure end point]
    (e.g., KMKC-ALL.WLDCT2.SLN)   
						

							190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 850229
FLIGHT MANAGEMENT
ARRIVAL (STAR)
A Standard Terminal Arrival (STAR) is loaded at the destination airport in the flight plan. Only one arrival 
can be loaded at a time in a flight plan. The route is defined by selection of an arrival, the transition waypoints, \
and a runway.
Figure 5-71  Arrival Loading Page - Selecting the Arrival
Destination Airport
Selected Arrival
Arrivals Available at KCOS
Arrival Waypoint Sequence
Preview of 
Selected Arrival
Selected Runway
Loading an arrival procedure into a stored flight plan:
1) Select a stored flight plan from the Flight Plan Catalog Page.
2) Select the EDIT Softkey; or press the MENU Key, select ‘Edit Flight Plan’, and press the ENT Key.  The Stored 
Flight Plan Page is displayed.
3) Select the LD STAR Softkey; or press the MENU Key, select “Load Arrival”, and press the ENT  Key.   The Arrival 
Loading Page is displayed.
4) Select an arrival.  Press the ENT Key.
5) Select a transition for the selected arrival.  Press the ENT Key.
6) Select a runway served by the selected arrival, if required.  Press the ENT Key.
7) Press the ENT Key to load the selected arrival procedure.  
						

							Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A230
FLIGHT MANAGEMENT
Figure 5-72  Arrival Loading Page - Selecting the Transition
Destination Airport
Selected Arrival
Transitions Available with 
DBRY1
Arrival Waypoint Sequence
Preview of 
Selected Arrival
Selected Transition
Figure 5-73  Stored Flight Plan Page - Arrival Inserted Inserted Arrival Header
 - Arrival Identifier: 
    [arrival airport]-[arrival transition].
    [arrival].[arrival runway]
    (e.g., KCOS-TBE.DBRY1.ALL)  
						

							190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 850231
FLIGHT MANAGEMENT
APPROACH (APPR)
An Approach Procedure (APPR) can be loaded at any airport that has an approach available. Only one 
approach can be loaded at a time in a flight plan. The route for a selected approach is defined by designating 
transition waypoints.
Figure 5-74  Approach Loading Page - Selecting the Approach
Destination Airport
Selected 
Approach
Approaches Available at 
KCOS
Approach Waypoint 
Sequence
Preview of  Selected 
Approach
BARO Minimum
Loading an approach procedure into a stored flight plan:
1) Select a stored flight plan from the Flight Plan Catalog Page.
2) Select the EDIT Softkey; or press the MENU Key, select ‘Edit Flight Plan’, and press the ENT Key.  The Stored 
Flight Plan Page is displayed.
3) Select the LD APR Softkey; or press the MENU Key, select “Load Approach”, and press the ENT Key.  The 
Approach Loading Page is displayed.
4) Select an approach.  Press the ENT Key.
5) Select a transition for the selected approach.  Press the ENT Key.
6) Press the ENT Key to load the selected approach procedure.  
						

							Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A232
FLIGHT MANAGEMENT
Figure 5-75  Approach Loading Page - Selecting the Transition
Destination Airport
Selected 
Approach
Transitions Available with 
Selected Approach
Approach Waypoint 
Sequence
Preview of  Selected 
Approach 
Load Approach? Selected Transition
Figure 5-76  Stored Flight Plan Page - Approach Inserted
Inserted Approach Header
 - Approach Identifier: [approach
    airport].[runway and approach type]
    (e.g., KCOS-RNAV 35R
GPS LPV)  
						

							190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 850233
FLIGHT MANAGEMENT
FLIGHT PLAN STORAGE
The G1000 can store up to 99 flight plans, numbered 1 through 99.  The active flight plan is erased when 
the G1000 is powered off or when another flight plan is activated.  Details about each stored flight plan can be 
viewed on the Flight Plan Catalog Page and on the Stored Flight Plan Page.
Viewing information about a stored flight plan:
1) Press the FPL Key on the MFD to display the Active Flight Plan Page.
2) Turn the small FMS Knob clockwise one click to display the Flight Plan Catalog Page.
3) Press the FMS Knob to activate the cursor and turn the FMS Knob to highlight the desired flight plan.
4) The Flight Plan Information is displayed showing departure, destination, total distance, and enroute safe altitude 
information for the selected Flight Plan.
5) Select the EDIT Softkey to open the Stored Flight Plan Page and view the waypoints in the flight plan.
6) Press the FMS Knob to exit the Stored Flight Plan Page.
Figure 5-77  Stored Flight Plan Information
Preview of Selected 
Flight Plan
Stored Flight Plan Info - Departure Airport
 - Destination Airport
 - Total Flight Plan Distance
 - Enroute Safe Altitude 
Flight Plan Name 
(Comment)
Selected Flight Plan
Stored FPL Editing  Softkeys
Storing an active flight plan from the Active Flight Plan Page or the Active Flight Plan Window:
1) Press the MENU Key.
2) Highlight ‘Store Flight Plan’.
3) Press the ENT Key.  
4) With ‘OK’ highlighted, press the ENT Key.  The flight plan is stored in the next available position in the flight 
plan list on the Flight Plan Catalog Page.  
						

							Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A234
FLIGHT MANAGEMENT
ACTIVATE A FLIGHT PLAN
Activating a stored flight plan erases the active flight plan and replaces it with the flight plan being activated. 
Inverting a stored flight plan reverses the waypoint order, erases the active flight plan, and replaces it with the 
flight plan being activated (the stored flight plan is not changed) 
Activating a stored flight plan on the MFD:
1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.
2) Press the FMS Knob to activate the cursor, and turn the FMS Knob to highlight the desired flight plan.
3) Select the ACTIVE Softkey; or press the ENT Key twice; or press the MENU Key, highlight ‘Activate Flight Plan’, 
and press the ENT Key.  The ‘Activate Stored Flight Plan?’ window is displayed. 
4) With ‘OK’ highlighted, press the ENT Key.  To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.
Inverting and activating a stored flight plan on the MFD:
1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.
2) Press the FMS Knob to activate the cursor, and turn the FMS Knob to highlight the desired flight plan.
3) Select the INVERT Softkey; or press the MENU Key, highlight ‘Invert & Activate FPL?’, and press the ENT  Key.  
The ‘Invert and activate stored flight plan?’ window is displayed.  
4) With ‘OK’ highlighted, press the ENT Key.  To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.
COPY A FLIGHT PLAN
The G1000 allows copying a flight plan into a new flight plan memory slot, allowing editing, etc., without 
affecting the original flight plan.  This can be used to duplicate an ex\
isting stored flight plan for use in creating 
a modified version of the original stored flight plan.
Copying a stored flight plan on the MFD:
1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.
2) Press the FMS Knob to activate the cursor, and turn the FMS Knob to highlight the desired flight plan.
3) Select the COPY Softkey; or press the MENU Key, highlight ‘Copy Flight Plan’, and press the ENT Key.  The 
‘Copy to Flight Plan XX?’ window is displayed. 
4) With ‘OK’ highlighted, press the ENT Key to copy the flight plan.  To cancel the request, press the CLR Key, or 
highlight ‘CANCEL’ and press the ENT Key.  
						

							190-00709-04  Rev. AGarmin G1000 Pilot’s Guide for the Socata TBM 850235
FLIGHT MANAGEMENT
DELETE A STORED FLIGHT PLAN
Individual or all stored flight plans can be deleted from the G1000 memory.
Deleting a stored flight plan:
1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.
2) Press the FMS Knob to activate the cursor, and turn the FMS Knob to highlight the desired flight plan.
3) Select the DELETE Softkey; press the CLR Key; or press the MENU Key, highlight ‘Delete Flight Plan’, and press 
the ENT Key.  The ‘Delete Flight Plan XX?’ window is displayed. 
4) With ‘OK’ highlighted, press the ENT Key to delete the flight plan.  To cancel the request, press the CLR Key, or 
highlight ‘CANCEL’ and press the ENT Key.
 NOTE:  The option to delete all stored flight plans is not available while the aircraft is in flight.
Deleting all stored flight plans:
1) Press the FPL Key and turn the small FMS Knob to display the Flight Plan Catalog Page.
2) Press the MENU Key.
3) Highlight ‘Delete All’ and press the ENT Key.  A ‘Delete all flight plans?’ confirmation window is displayed. 
4)  With ‘OK’ highlighted, press the ENT Key to delete all flight plans.  To cancel the request, press the CLR Key, or 
highlight ‘CANCEL’ and press the ENT Key.
FLIGHT PLAN EDITING
The active flight plan or any stored flight plan can be edited. The edits made to the active flight pl\
an affect 
navigation as soon as they are entered.
DELETING THE ACTIVE  FLIGHT  PLAN
The G1000 allows deleting an active flight plan.  Deleting the active \
flight plan suspends navigation by the 
G1000. 
Deleting the active flight plan:
1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
2) Press the MENU Key, highlight ‘Delete Flight Plan’, and press the ENT Key.  The ‘Delete all waypoints in flight 
plan?’ window is displayed. 
3) With ‘OK’ highlighted, press the ENT Key to delete the active flight plan.  To cancel the request, press the CLR 
Key, or highlight ‘CANCEL’ and press the ENT Key.  
						

							Garmin G1000 Pilot’s Guide for the Socata TBM 850190-00709-04  Rev. A236
FLIGHT MANAGEMENT
DELETING FLIGHT PLAN ITEMS
Individual waypoints, entire airways, and entire procedures can be deleted from a flight plan. Some waypoints 
in the final approach segment (such as the FAF or MAP) can not be deleted individually. Attempting to delete 
a	waypoint	that	is	not	allowed	results	in	a	window	displaying	‘Invalid	flight	plan	modification.’
Deleting an individual waypoint from the active flight plan:
1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
2) Press the FMS Knob to activate the cursor (not required on the PFD) and turn the large FMS Knob to highlight 
the waypoint to be deleted.
3) Press the CLR Key.  The ‘Remove XXXXX?’ window is displayed.
4) With ‘OK’ highlighted, press the ENT Key. To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.
5) Press the FMS Knob to remove the flashing cursor.
Deleting an entire airway from the active flight plan:
1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
2) Press the FMS Knob to activate the cursor (not required on the PFD) and turn the large FMS Knob to highlight 
the white header of the airway to be deleted.
3) Press the CLR Key.  The ‘Remove ?’ window is displayed.
4) With ‘OK’ highlighted, press the ENT Key.  To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.
5) Press the FMS Knob to remove the flashing cursor.
Deleting an entire procedure from the active flight plan:
1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
2) Press the FMS Knob to activate the cursor (not required on the PFD) and turn the large FMS Knob to highlight 
the white header of the procedure to be deleted.
3) Press the CLR Key.  The ‘Remove  from flight plan?’ window is displayed.\
4) With ‘OK’ highlighted, press the ENT Key.  To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.
5) Press the FMS Knob to remove the flashing cursor.
 Or:
1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
2) Press the MENU Key to display the Page Menu and turn the FMS Knob to highlight ‘Remove ’.
3) Press the ENT Key. The ‘Remove  from flight plan?’ window is displayed.\
4) With ‘OK’ highlighted, press the ENT Key.  To cancel the request, press the CLR Key, or highlight ‘CANCEL’ and 
press the ENT Key.