Konica Minolta bizhub 211 User Manual

							Utility mode/Copy mode parameters7
bizhub 163/211 7-27
6Press the [+] or [,] key until the desired paper type is selected, and 
then press the [OK] key.
The PAPER SOURCE SETUP menu appears again.
TRAY1 MEDIA TYPE
TRANSPARENCY
PLAIN
CARD
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-28 bizhub 163/211Specifying special paper settings for paper drawers (PAPER TYPE 
parameter)
1Display the PAPER SOURCE SETUP menu.
– Refer to Displaying the PAPER SOURCE SETUP menu on 
page 7-21.
2Press the [+] or [,] key until PAPER TYPE is selected, and then press 
the [OK] key.
3Press the [+] or [,] key until the desired paper drawer is selected, and 
then press the [OK] key.
UTILITY MODE 
PAPER SOURCE SETUP
MACHINE SETTING
CUSTOM SIZE MEMORY
PAPER SOURCE SETUP
TRAY1 PAPER
INCH/METRIC
PAPER TYPE
PAPER TYPE
TRAY2
TRAY1
TRAY3
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-29
4Press the [+] or [,] key until the desired special paper type is selected, 
and then press the [OK] key.
The PAPER SOURCE SETUP menu appears again.
2
Note 
1-SIDE appears only when the machine is equipped with the duplex 
unit (option for the bizhub 211 only).
TRAY1 PAPER TYPE
RECYCLE
PLAIN
SPECIAL
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-30 bizhub 163/211
7.5 CUSTOM SIZE MEMORY
From the CUSTOM SIZE MEMORY menu, two of the most frequently used 
custom paper sizes can be registered. The custom paper sizes registered 
here can be selected for the size of paper loaded in the 1st paper drawer by 
selecting PAPER SOURCE SETUP in Utility mode, then selecting TRAY1 
PAPER, then PAPER SIZE.
CUSTOM SIZE MEMORY options
Registering a custom paper size
1Press the [Utility] key.
The UTILITY MODE menu appears.
2Press the [+] or [,] key until CUSTOM SIZE MEMORY is selected, 
and then press the [OK] key.
The CUSTOM SIZE MEMORY menu appears.
No.CUSTOM SIZE MEMO-
RYDescription
1 MEMORY1 Frequently used paper sizes can be registered and recalled 
when needed. The following sizes can be registered.
Length: 140 mm to 432 mm
Width: 90 mm to 297 mm 2MEMORY2
UTILITY MODE 
PAPER SOURCE SETUP
MACHINE SETTING
CUSTOM SIZE MEMORY
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-31
3Press the [+] or [,] key until the desired number is selected, and then 
press the [OK] key.
4Use the keypad to type in length (X), and then press the [OK] key.
– Refer to the diagram and be sure 
to specify the paper width and 
length measurements correctly.
– The paper length (X) can be set 
between 140 mm and 432 mm.
– To correct the entered value, 
press the [Clear/Stop] key.
CUSTOM SIZE MEMORY
MEMORY2
MEMORY1
RETURN
CUSTOM SIZE MEMORY1 
 Y=297( 90-297)
 X=210(140-432)  x
length (X)
width (Y)
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-32 bizhub 163/211
5Use the keypad to type in width (Y), and then press the [OK] key.
– The paper width (Y) can be set between 90 mm and 297 mm.
– To correct the entered value, press the [Clear/Stop] key.
The CUSTOM SIZE MEMORY menu appears again.
CUSTOM SIZE MEMORY1 
 Y=297( 90-297)
 X=210(140-432)  x
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-33
7.6 USER MANAGEMENT
From the USER MANAGEMENT menu, certain maintenance operations 
can be performed in order to maintain the machine’s efficiency.
USER MANAGEMENT functions
Drying (dehumidifying) the drum (DRUM DEHUMIDIFY function)
1Press the [Utility] key.
The UTILITY MODE menu appears.
2Press the [+] or [,] key until USER MANAGEMENT is selected, and 
then press the [OK] key.
The USER MANAGEMENT menu appears.
No.USER MANAGEMENTDescription
1 DRUM DEHUMIDIFY When the room temperature changes drastically (such as 
when a heater is used in the winter) or when the machine is 
used in an extremely humid location, condensation may form 
on the surface of the PC drum inside the machine, resulting in 
decreased print quality. If this occurs, use this function to dry 
the drum and eliminate the condensation. The drum dehumid-
ifying operation lasts approximately three minutes.
2 TONER  REPLENISHER After many documents containing large printed areas (such as 
photos) or many negative/positive-inverted copies/printouts 
are printed, the print density may temporarily become too light 
if toner is not automatically replenished. If this occurs, use this 
function to force replenishing of the toner and immediately re-
turn the density to its normal level.
UTILITY MODE
ADMIN. MANAGEMENT
USER MANAGEMENT
COPY SETTING 1
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-34 bizhub 163/211
3Press the [+] or [,] key until DRUM DEHUMIDIFY is selected, and 
then press the [OK] key.
Drum drying begins, and the USER MANAGEMENT menu appears 
again.
USER MANAGEMENT
TONER REPLENISHER
DRUM DEHUMIDIFY
RETURN
Downloaded From ManualsPrinter.com Manuals 
						

							Utility mode/Copy mode parameters7
bizhub 163/211 7-35Replenishing toner (TONER REPLENISHER function)
1Press the [Utility] key.
The UTILITY MODE menu appears.
2Press the [+] or [,] key until USER MANAGEMENT is selected, and 
then press the [OK] key.
The USER MANAGEMENT menu appears.
3Press the [+] or [,] key until TONER REPLENISHER is selected, and 
then press the [OK] key.
Toner replenishing begins, and the USER MANAGEMENT menu 
appears again.
UTILITY MODE
ADMIN. MANAGEMENT
USER MANAGEMENT
COPY SETTING 1
USER MANAGEMENT
TONER REPLENISHER
DRUM DEHUMIDIFY
RETURN
Downloaded From ManualsPrinter.com Manuals 
						

							7Utility mode/Copy mode parameters
7-36 bizhub 163/211
2
Reminder 
While toner is being refilled, do not turn off the machine or open the 
machine’s front door.
2
Note 
If the density of the toner is suitable, do not perform the toner 
replenishing operation.
Downloaded From ManualsPrinter.com Manuals