Konica Minolta bizhub 211 User Manual

							When a message appears8
bizhub 163/211 8-13
4Pull out the paper drawer.
5Remove all paper from the drawer, 
and then load the drawer with paper 
again.
– Load the paper so that it fits 
under the tabs and so that the top 
of the stack is not higher than the 
, mark.
6Slide the paper guides to fit the size 
of paper being loaded.
– Be sure that the paper guides are 
slid up against the edges of the 
loaded paper.
Downloaded From ManualsPrinter.com Manuals 
						

							8When a message appears
8-14 bizhub 163/211
7Close the paper drawer.
Downloaded From ManualsPrinter.com Manuals 
						

							When a message appears8
bizhub 163/211 8-15Clearing a paper misfeed in the multi bypass tray (optional)
1Remove all paper from the multi 
bypass tray.
2Open the right-side door of the 
machine.
– Decreased copy quality may 
result if the surface of the image 
transfer roller is touched.
Be careful not to touch the 
surface of the image transfer 
roller.
Image transfer roller
Downloaded From ManualsPrinter.com Manuals 
						

							8When a message appears
8-16 bizhub 163/211
3Slowly pull out the paper.
4Close the right-side door of the 
machine.
5Reload paper into the multi bypass 
tray.
Downloaded From ManualsPrinter.com Manuals 
						

							When a message appears8
bizhub 163/211 8-17Clearing a paper misfeed in the duplex unit (option for bizhub 211 only)
The optional duplex unit must be installed.
1Open the duplex unit cover.
2Carefully pull out any misfed paper.
3Close the duplex unit cover.
Downloaded From ManualsPrinter.com Manuals 
						

							8When a message appears
8-18 bizhub 163/211
8.3 When the message ORIGINAL DOC. JAM appears
If the document is misfed, the following message appears and scanning of 
the document stops.
Follow the appropriate procedure described below to clear the misfed paper.
______CAUTION_______
OPEN DOC.FEED COVER
 ORIGINAL DOC. JAM
Downloaded From ManualsPrinter.com Manuals 
						

							When a message appears8
bizhub 163/211 8-19Clearing a paper misfeed in the document feeder
1Open the misfeed-clearing cover.
2Remove all document pages from 
the document feed tray.
3Lift open the document feeder.
Downloaded From ManualsPrinter.com Manuals 
						

							8When a message appears
8-20 bizhub 163/211
4While turning the knob on the 
document feeder in the direction of 
the arrow, slowly pull out the 
document.
5Close the document feeder and the 
misfeed-clearing cover.
6Reload the tray with the document 
pages removed in step 2.
– If the message RETURN 
ORIGINAL to ADF and PRESS 
START KEY appears on the 
display, return the document 
pages that caused the misfeed to 
their original positions.
Downloaded From ManualsPrinter.com Manuals 
						

							When a message appears8
bizhub 163/211 8-21
8.4 Main error messages and their remedies
MessageCauseRemedy
PAPER JAM
OPEN 1st SIDE COVERA paper misfeed occurred in 
the machine.Open the cover at the indicated 
location, and then remove the 
misfed paper. Refer to When 
the message PAPER JAM 
appears on page 8-6.
All misfed paper was not re-
moved from inside of the ma-
chine.Open the cover at the indicated 
location, and then remove all 
misfed paper. Refer to When 
the message PAPER JAM 
appears on page 8-6.
ORIGINAL DOC.JAM
OPEN DOC.FEED COVERA document misfeed occurred 
in the document feeder. All 
misfed paper was not removed 
from the document feeder.Open the cover at the indicated 
location, and then remove the 
misfed paper. Refer to When 
the message ORIGINAL DOC. 
JAM appears on page 8-18.
REMOVE PAPER
IN BYPASS TRAYPaper remains in the manual 
bypass tray.Remove the paper from the 
manual bypass tray.
FRONT COVER OPEN
CLOSE FRONT COVERThe front door of the machine is 
open or not securely closed.Securely close the front door of 
the machine.
DUPLEX COVER OPEN
CLOSE DUPLEX COVERThe duplex unit cover is open 
or not securely closed.Securely close the duplex unit 
cover.
DOCUMENT COVER OPEN
CLOSE DOCUMENT COV-
ERThe document feeder is raised 
while a document is loaded into 
it.Securely close the document 
feeder.
DOC.FEED COVER OPEN
CLOSE DOC.FEED COVERThe misfeed-clearing cover of 
the document feeder is open.Securely close the misfeed-
clearing cover.
TONER EMPTY
SUPPLY TONERThe toner is empty.
Copying/printing cannot be 
performed.Replace the toner bottle with a 
new one. Refer to Replacing 
the toner bottle on page 8-4.
PAPER EMPTY
LOAD PAPER (#XXX)The selected paper drawer has 
run out of paper. # indicates 
the paper drawer, and XXX 
indicates the paper size.Load paper of the specified 
size into the specified paper 
drawer.
SET ORIGINAL TO ADF A document was not loaded 
into the document feeder be-
fore beginning a copy function 
(such as, Mixed Original cop-
ying) that uses the document 
feeder. Otherwise, the docu-
ment feeder is raised.Load a document into the doc-
ument feeder.
REMOVE ORIGINAL IN 
ADFWhen interrupting a copy job to 
perform a different copy opera-
tion other than the BOOK 
SEPARATION function, the 
document for the interrupted 
copy job was left in the docu-
ment feeder.Remove the document from the 
document feeder.
Downloaded From ManualsPrinter.com Manuals 
						

							8When a message appears
8-22 bizhub 163/211
Paper Empty (when specifying copy settings)
The selected paper drawer 
contains no paper.
# indicates the paper drawer, 
and XXX indicates the paper 
size.Either load paper of the speci-
fied size into the specified pa-
per drawer, or press the [Paper] 
key and select a different paper 
size.
NO SUITABLE PAPER
LOAD PAPER (#XXX)• The paper size setting for the 
selected paper drawer was 
changed while copying.
• While copying with the 
Mixed Original setting and 
the AUTO Paper setting 
selected, paper of a suitable 
size cannot be found. # in-
dicates the paper drawer, 
and XXX indicates the pa-
per size.Either load paper of the speci-
fied size, or press the [Paper] 
key and select a different paper 
size.
APS  SIZE  ERROR  (#XXX) While copying with the AUTO 
Paper setting selected, paper 
of a suitable size cannot be 
found.Either load paper of a suitable 
size, or press the [Paper] key 
and select a different paper 
size.
AMS  SIZE  ERROR While copying with the AUTO 
Zoom setting selected, the 
combination of the document 
and paper sizes caused the 
zoom ratio to exceed the range 
between 25% and 400%.Either load paper of a suitable 
size, or press the [Zoom] key 
and select a different zoom ra-
tio.
PAPER SIZE ERROR
RESET PAPER (#XXX)The paper loaded in the paper 
drawer caused a size error. # 
indicates the paper drawer, and 
XXX indicates the paper size.For a paper feed unit, remove 
the loaded paper, and then re-
load the paper according to the 
procedure described in Load-
ing paper on page 4-9. For pa-
per of a non-standard size, 
refer to Copying onto label 
sheets on page 5-38. For a by-
pass tray, remove the loaded 
paper, and then reload the pa-
per according to the procedure 
described in Loading plain pa-
per into the bypass tray on 
page 5-18. For paper of a non-
standard size, refer toCopying 
onto manually fed paper (man-
ual bypass tray) on page 5-28.
MEMORY FULL
(PRESS ANY KEY)The size of the data for the 
scanned image has exceeded 
the capacity of the memory.Press any control panel key, or 
turn the machine off, then on 
again. (The scan data should 
be cleared from the memory.)
MEMORY FULL
(PRESS ANY KEY)The image data received from 
the computer has exceeded 
the capacity of the memory.Press any control panel key, or 
turn the machine off, then on 
again. (The received image 
data should be cleared from 
the memory.)
MessageCauseRemedy
Downloaded From ManualsPrinter.com Manuals