Home > Land Rover > Automobile > Land Rover 90 110 Workshop Rover Manual

Land Rover 90 110 Workshop Rover Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Land Rover 90 110 Workshop Rover Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 364 Land Rover manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    Page
    of 720
    							CHASSIS AND BODY El 
    .. . . .... r”,,.. ’: ., , . :I 4.:: : . ... .~. 
    A FrontDatum 
    B Chassis Datum 
    C Front axle centre line 
    D  Rear axle centre 
    line 
    1. 4148 - 4143 mm 
    2. 40093-4005 mm 
    3. 978,7-981,2 mm 
    4. 22-20” 
    5. 252-250 mm 
    6. 239-236,5 mm 
    7. 3023,3-3022,3 mm 
    8. 3030,7-3028,7 mm 
    9. 155- 153 mm 
    10. 871,2-869,2 mm 
    11.  2794 mm - Wheelbase 
    12. 488 - 433 mm 
    13. 488 - 433 mm 
    14. 82-79,5 mm 
    15. 750,9 mm 
    16. 750,9 mm 
    17. 4393 - 4363 mm 
    18. 4393 -4363 mm 
    19. 2993 - 2953 mm 
    20. 500-495 mm 
    21. 500 - 495 mm 
    22. 594,2-593,4 mm 
    -- 
    LAND ROVER 110 
    CHASSIS  ALIGNMENT  DIMENSIONS 
    23. 594,2 - 593,4 mm 
    24. 283 - 282,2 mm 
    25. 283 - 282,2 mm 
    26. 1970- 1968 mm 
    27. 642,9-639,5 mm 
    28. 590,5 mm 
    29. 295,25 mm 
    30. 136,5 mm 
    31.  103 - 100 mm 
    32. 1177,5- 1175,5 mm 
    33. 1692,5 - 1689,5 mm 
    34. 2610-2606 mm 
    35. 2040,5 -2037,5 mm 
    36. 1912,5 - 1909,5 mm 
    37. 1359- 1357 mm 
    38. 1573- 1571 mm 
    39. 270 - 268 mm 
    40. 665,5-633,5 mm 
    41,  440 - 438 mm 
    I. . 
    5  
    						
    							CHASSIS AND BODY 1761 
    DOORS - 1986 ONWARDS 
    7  
    						
    							176 I CHASSIS AND BODY 
    REMOVING THE DOOR TRIM - Front and rear 
    doors 
    1. Prise off the  two  finishers  and remove  the two 
    screws  securing  the door  pull. 
    -. -- .___ - ...- . 
    1. 
    5. Lever off the window  regulator center finisher and 
    remove  the retaining  screw and withdraw  the 
    handle  and bezel. 
    2. Remove the single Screw behind the remote control 6- Using a screwdriver, the trim away 
    lever. from the door. 
    3. Prise off the remote  control  lever bezel. Fitting  door trim 
    7. Remove  any trim  fasteners  held in the  door  panel 
    and  insert  them into the back 
    of the trim  or use  new 
    ones. 
    8. Ensure  that the anti-vibration pads  are in position 
    and  offer
    -up the  trim  to the  door,  lining-up the 
    fasteners  with the holes  in the  door  and push  the 
    trim  into position. 
    4. Prise off the door  locking  button bezci. 
    , 
    8  
    						
    							CHASSIS AND BODY 
    . I. ,. 9. Fit the  bezels  to  the  locking  button and  remote 
    10. Fit  the  single screw  behind  the  remote control 
    11. Fit the door  pull and secure  with two screws  and 
    12. Fit the  window  regulator  handle and retain  with the 
    control 
    lever. 
    lever. 
    finishers. 
    single screw  and finisher. 
    ,  ~ .. I. I 
    76 
    REMOVING 
    WINDOW REGULATORS - rear side 
    door 
    Fitting regulator 
    channel. 
    5. Insert  the lifting  arm button  into  the  lifting 
    To remove 
    1. Remove  the door trim. 
    2. Remove the  protective weather sheet. 
    3. Temporarily  fit the handle  and wind  the window  up 
    position,  with a  length 
    of timber,  to  prevent it 
    falling when removing  the regulator. 
    4. Remove the  four  screws retaining the regulator to 
    the  mounting  panel and withdraw  the regulator 
    whilst  sliding  the lifting arm  button  from the lifting 
    channel. 
    To assist  this operation,  remove the 
    timber  and lower  the glass. 
    . - to its  fullest  extent and support  the  glass  in this 
    r-----.-----. - -1 
    c-- --- -/-- ST1903M 
    6. Position  the regulator so that  the fixing  holes 
    line
    -up  with  the holes in the  mounting  panel. 
    7. Secure with the four  screws and  tighten  evenly. 
    8. Temporarily  fit the  handle  and check  that glass can 
    be  raised  and  lowered  smoothly without tight 
    spots. 
    9. Fit  the weather protection  sheet with adhesive. 
    10. Fit the door trim,  regulator handle,  door pull, and 
    bezels. 
    9  
    						
    							76 
    REMOVING EXTERIOR HANDLE - rear side door 
    CHASSIS AND BODY 
    To remove 
    1. Remove the door  trim,  regulator handle, door pull 
    and bezels. 
    2. Peel  back  sufficient  of the  weather protection  sheet 
    to  gain  access 
    to the handle  mechanism. 
    3. Disconnect  the  actuating  rod from  the handle 
    operating  lever. 
    4. Remove the  two  screws  and  withdraw the handle 
    and  bezels. 
    Fitting 
    handle 
    5. Fit the  handle  to the  door  ensuring  that  the two 
    bezels  are 
    in position - flat faces  towards  the door 
    and  secure  with the two  screws. 
    STi904M’ 
    6. 
    7. 
    8. 
    Connect  the actuating  rod to the  handle  operating 
    lever  and secure  with spring  clip. 
    Re-scal the weather  protection  sheet. 
    Fit  the  door  trim, regulator  handle, door  pull and 
    bezels. 
    RENEWING  DOOR LOCKING  BUTTON - rear side 
    door 
    To remove 
    1. Remove  the door  trim, regulator handle, door  pull 
    and  bezels. 
    2. Peel back  sufficient  of the weather  protection sheet 
    to reveal the mechanism. 
    3. Release  the  spring clip securing  the  button  to  the 
    operating  rod and  withdraw 
    the rod from the 
    button. 
    4. Remove  the two screws securing  the button  to the 
    door  panel  and remove  the button. 
    Fitting  locking  button 
    5. Secure  the locking  button assembly  to the  door 
    panel  with the two  screws. 
    6. Fit the  operating  rod to the  button  assembly  and 
    secure  with the spring  clip. 
    7. Reseal  the weather  protection  sheet  and fit the 
    door  trim,  door 
    pull, regulator  handle and bezels. 
    10  
    						
    							CHASSIS AND BODY 176 
    RENEW REMOTE  CONTROL  LEVER - rear side 
    door 
    To remove 
    1. Remove  the door  trim,  door pull, regulator  handle 
    2. Peel-back sufficient  of the  weather protection  sheet 
    3. Remove the spring clip and disconnect  the control 
    and 
    bezels. 
    to  gain  access  to the  remote  lever. 
    rod from  the locking  button. 
    Fitting control  lever 
    9. Fit the  plastic  retaining  clips to the  rod  assembly 
    10. Connect  the control  rods to the latch  assembly and 
    11. Fit the plastic  retaining  rod clips  to  the  mounting 
    12. Connect  the  control  rod  to the  locking  button and 
    13. Re-seal the  weather  protection sheet and fit the 
    into 
    position  and secure  with the two  screws. 
    secure  with the clips. 
    panel. 
    secure  with the clip. 
    trim  panel,  regulator  handle, door pull and bezels. 
    REMOVE  DOOR LATCH  ASSEMBLY - rear side 
    door 
    To remove 
    1. Remove  the  door pull, regulator  handle,  bezels 
    2. Peel-back sufficient of the weather  protection sheet 
    3. Release the remote  control lever rod from the latch 
    4. Disconnect  the door  outer  handle  control  rod from 
    and 
    door  trim. 
    to reveal  the latch. 
    assembly. 
    the  latch assembly. 
    5. Disconnect  the door  locking  button remote  control 
    6. Remove the  three  retaining screws and withdraw 
    4. Release  the spring  clip  and disconnect  the  short 
    locking  button  control  rod from  the latch 
    mechanism. 
    5. Disconnect  the long  remote  control  rod  from  the 
    latch assembly. 
    6. Remove  the two  screws  securing  the remote 
    control lever  to the mounting panel. 
    7. Release  the control  rods from  the  plastic  retaining 
    clips  located  in the  mounting panel. 
    8. Withdraw  the  remote  control  lever and rods  from 
    the door.  rod 
    from the  latch mechanism. 
    the  latch assembly  from the door. 
    continued 
    SI ’ , 
    11  
    						
    							76 
    Fitting the latch 
    7. Fit the  latch  assembly  to the  door  and secure  with 
    the  three  screws, noting that  the uppermost  screw 
    is longer. 
    8. Connect the remote  control  levers to  the  latch 
    mechanism  reversing instructions 
    3,4 and 5. 
    9. Re-seal the weather  protection  sheet  and fit the 
    regulator handle,  door pull, door  trim and bezels. 
    CHASSIS AND BODY 
    REMOVING DOOR GLASS - rear  side door 
    To remove 
    1. Disconnect  the door  check  rod from  the door  post. 
    2. Remove  the regulator  handle,  door  pull, bezels 
    3. Remove  the weather protection sheet. 
    5. Disconnect  and remove  the door  locking  button. 
    6. Disconnect  the  control  rods from the latch  and 
    and door 
    trim. 
    . 4. Remove the window  regulator  assembly. 
    door outer  handle mechanism.  Remove 
    the four  screws  retaining  the mounting 
    e 
    panel to the door  and remove  the  panel  complete 
    with  rods  and control  lever. 
    ST191OM // 
    8. Remove the  single self tapping  screw to remove the 
    water channel. 
    9. Remove the  door check torsion  bar. 
    10. Remove  the door check  rod by bending  back the 
    end stop to enable the rod to be withdrawn. 
    12  
    						
    							CHASSIS AND BODY (761 
    .: 
    . . :.... .Y. ..L.-? 
    11. Remove the four  self-tapping  screws - two each 
    12. Remove  the inner  and outer  weather  strips from 
    .*.
    						
    							1761 CHASSIS AND BODY 
    REMOVING MOUNTING  PANEL - front doors 
    To remove 
    1. Remove  the  door  trim, window regulator,  door 
    pull,  bezels  and weather  protection  sheet. 
    2. Remove the four  screws  securing  the window 
    regulator  to the  mounting  panel. 
    3. Remove the five screws securing  the mounting 
    panel  to the  door frame. 
    4. Release  the remote  control  lever rod from the  latch 
    mechanism  and from  the plastic  clip 
    in the 
    mounting panel. 
    5. Slide the  window regulator  arm from  the mounting 
    panel  channel  and  remove  the panel with the 
    remote  control lever  and rod. 
    Fitting mounting  panel 
    6. Engage the  window regulator arm  in the  mounting 
    panel  channel. 
    7. Connect  the remote  control  rod  to the  latch 
    mechanism  and secure with the clip. 
    8. Fit  the  mounting  panel and retain  with the five 
    screws. 
    9. Secure the  window regulator  to the  mounting  panel 
    with  the four  screws. 
    10. Raise and  lower  the window  to check  for free 
    movement. 
    11. Fit  the  weather  protection  sheet,  door trim, 
    window  regulator  handle, door pull and bezels. 
    REMOVING  DOOR LOCKING  BUTTON - front 
    doors 
    To remove 
    1. Remove  the  door trim regulator  handle,  door pull 
    2. Peel back  sufficient of the weather  protection  sheet 
    3. Release  the  spring  clip and disconnect  the 
    4. Remove the  two  screws and withdraw  the locking 
    and 
    bezels. 
    to  expose  the mechanism. 
    operating  rod from  the latch mechanism. 
    button  assembly. 
    continued 
    14  
    						
    All Land Rover manuals Comments (0)

    Related Manuals for Land Rover 90 110 Workshop Rover Manual