Lexmark C 950 Service Manual

							Repair information 4-217
  5058-030
Go Back Previous
Next
Tray module transport rollers removal
This removal procedure applies to all three tray modules.
1.Open the left door. 
2.Remove the e-clip (A).
3.Move the tray module transport roller toward the rear of the machine, and detach it from the machine. 
4.Remove the tray module transport roller from the machine. 
						

							4-218  Service Manual 5058-030  
Go Back Previous
Next
Tray module tray 2 media turn guide removal
1.Open the left door.
2.Gently press the lower edges of the tray module 2 media turn guide.
3.Remove the tray module 2 media turn guide from the machine.
Tray module upper transport motor removal
This removal procedure is not applicable to TTM tray modules.
1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215.
2.Disconnect the cable (A).
3.Release the harness from the clamp (B). 
						

							Repair information 4-219
  5058-030
Go Back Previous
Next
4.Remove the two screws (C).
5.Remove the tray module upper transport motor.
TTM left door removal
1.Remove the tray module left cover. See “Tray module left cover removal” on page 4-210.
2.Open the TTM left door. 
						

							4-220  Service Manual 5058-030  
Go Back Previous
Next
3.Remove the metal clip from the hinge.
4.Lift the TTM left door and remove it from the machine.
TTM lower transport motor removal
1.Remove the tray module rear cover. See “Tray module rear cover removal” on page 4-215.
2.Disconnect the cable (A).
3.Release the harness from the clamp (B). 
						

							Repair information 4-221
  5058-030
Go Back Previous
Next
4.Remove the two screws (C) securing the TTM lower transport motor to the machine.
Note:  When removing the TTM lower transport motor, the drive belt will become detached. 
5.Remove the TTM lower transport motor.
Reinstallation note:  To correctly set the drive belt tension, install the TTM lower transport motor and the TTM 
lower transport motor tension spring before completely tightening the three screws.
TTM tray 3 feeder removal
1.Remove the TTM tray 3 media tray out from the machine. See “TTM tray 3 media tray removal” on 
page 4-224.
2.Pull open, but do not remove, the TTM tray 4 media tray.
3.Open the left door. 
						

							4-222  Service Manual 5058-030  
Go Back Previous
Next
4.Remove the two screws (A) from the inside of the tray module securing the TTM tray 3 feeder to the 
machine.
5.Remove the two screws (B) securing the TTM tray 3 feeder to the machine. 
6.Disconnect the two cables (C). 
						

							Repair information 4-223
  5058-030
Go Back Previous
Next
7.Release the two harnesses from the clamps (D).
8.Remove the TTM tray 3 feeder.
Reinstallation note:  When replacing the TTM tray 3 feeder, ensure that the rear metal bracket is removed and 
installed on the new TTM tray 3 feeder. 
						

							4-224  Service Manual 5058-030  
Go Back Previous
Next
TTM tray 3 media tray removal
1.Pull the TTM tray 3 media tray from the machine.
2.Remove the screw (A) securing the lock bracket to the machine.
3.Remove the bracket from the machine. 
4.Gently lift and remove the TTM tray 3 media tray from the machine. 
						

							Repair information 4-225
  5058-030
Go Back Previous
Next
TTM tray 3 media turn guide removal
1.Open the left door. 
2.Gently press the lower edges of the tray module 3 media turn guide.
3.Remove tray module 3 media turn guide from the machine.
TTM tray 4 media feeder removal
1.Remove the tray 2 from the machine.
2.Pull the TTM tray 4 media tray out from the machine. 
						

							4-226  Service Manual 5058-030  
Go Back Previous
Next
3.Remove the three screws (A) from inside the tray module.
4.Disconnect the two cables (B).