Samsung CLX 8380ND User Manual

							
4
Scanning ..............................................................................................................................  47
Scanning with USB  .......................................................................................................  47
Scanning with network  ..................................................................................................  47
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
5
1Installing Printer 
Software in Windows
This chapter includes:
• Installing Printer Software
• Reinstalling Printer Software
•Removing Printer Software
• Installing mono printer driver
NOTE: The following procedure is based on Windows XP, for 
other operating systems, refer  to the corresponding Windows 
users guide or online help.
Installing Printer Software
You can install the printer software for local printing or network 
printing. To install the printer software on the computer, 
perform the appropriate installation procedure depending on 
the printer in use.
A printer driver is software that lets your computer 
communicate with your printer.  The procedure to install drivers 
may differ depending on the operating system you are using.
All applications should be closed  on your PC before beginning 
installation. 
Installing Software for Local Printing
A local printer is a printer direct ly attached to your computer 
using the printer cable supplied with  your printer, such as a USB 
or parallel cable. If your printe r is attached to a network, skip 
this step and go to “Installing Software for Network Printing” on 
page 8.
You can install the printer software using the typical or custom 
method.
NOTE: If the “New Hardware Wizard” window appears during 
the installation procedure, click   in the upper right corner of 
the box to close the window, or click Cancel.
Typical Installation
This is recommended for most users. All components necessary 
for printer operations will be installed.
1Make sure that the printer is connected to your computer 
and powered on.
2Insert the supplied CD-ROM  into your CD-ROM drive.
The CD-ROM should automatically run, and an installation 
window appears.
If the installation window does not appear, click 
Start and 
then 
Run. Type X:\Setup.exe, replacing “X” with the 
letter which represents your drive and click 
OK.
If you use Windows Vista, click 
Start → All programs → 
Accessories → Run, and type X:\Setup.exe.
If the 
AutoPlay window appears in  Windows Vista, click 
Run Setup.exe in Install or run program field, and 
click 
Continue in the User Account Control window.
3Click Next. 
• If necessary, select a language from the drop-down list.
4Select Typical installation for a local printer. Click 
Next.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
6
NOTE: If your printer is not already connected to the 
computer, the following window will appear.
• After connecting the printer, click 
Next.
• If you don’t want to connect the printer at this time, click 
Next, and No on the following screen. Then the installation 
will start and a test page will not be printed at the end of the 
installation.
• The installation window that appears in this User’s  Guide may differ depending on the printer and 
interface in use.
5After the installation is fini shed, a window asking you to 
print a test page appears. If you choose to print a test 
page, select the checkbox and click 
Next.
Otherwise, just click 
Next and skip to step 7.
6If the test page prints out correctly, click Yes.
If not, click 
No to reprint it.
7To register yourself as a user  of Samsung Printers in order 
to receive information from  Samsung, select the checkbox 
and click 
Finish. You are now sent to the Samsung web 
site.
Otherwise, just click 
Finish.
NOTE: After setup is complete, if your printer driver doesn’t 
work properly, reinstall the printer driver. See “Reinstalling 
Printer Software” on page 11.
Custom Installation
You can choose individual components to install.
1Make sure that the printer is  connected to your computer 
and powered on.
2Insert the supplied CD-ROM  into your CD-ROM drive.
The CD-ROM should automatically run, and an installation 
window appears.
If the installation window does not appear, click 
Start and 
then 
Run. Type X:\Setup.exe, replacing “X” with the 
letter which represents your drive and click 
OK.
If you use Windows Vista, click 
Start → All programs → 
Accessories → Run, and type X:\Setup.exe.
If the 
AutoPlay window appears in  Windows Vista, click 
Run Setup.exe in Install or run program field, and 
click 
Continue in the User Account Control window.
3Click Next. 
• If necessary, select a language from the drop-down list.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
7
4Select Custom installation. Click Next.
5Select your printer and click Next.
NOTE: If your printer is not already connected to the 
computer, the following window will appear.
• After connecting the printer, click 
Next.
• If you don’t want to connect the printer at this time, click 
Next, and No on the following screen. Then the installation 
will start and a test page will not be printed at the end of the 
installation.
• The installation window th at appears in this User’s 
Guide may differ depending on the printer and 
interface in use.
6Select the components to be installed and click Next.
NOTE: You can change the desire d installation folder by 
clicking [Browse].
7After the installation is finished, a window asking you to 
print a test page appears. If you choose to print a test 
page, select the checkbox and click 
Next.
Otherwise, just click 
Next and skip to step 9.
8If the test page prints out correctly, click Yes.
If not, click 
No to reprint it.
9To register yourself as a user  of Samsung Printers in order 
to receive information from Samsung, select the checkbox 
and click 
Finish. You are now sent  to the Samsung web 
site.
Otherwise, just click 
Finish.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
8
Installing Software for Network 
Printing
When you connect your printer to a network, you must first 
configure the TCP/IP settings fo r the printer. After you have 
assigned and verified the TCP/ IP settings, you are ready to 
install the software on each  computer on the network.
You can install the printer software using the typical or custom 
method.
Typical Installation
This is recommended for most us ers. All components necessary 
for printer operations will be installed.
1Make sure that the printer is connected to your network 
and powered on. For details about connecting to the 
network, see the supplied printer’s User’s Guide.
2Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automaticall y run, and an installation 
window appears.
If the installation window does not appear, click 
Start and 
then 
Run. Type X:\Setup.exe, replacing “X” with the 
letter which represents your drive and click 
OK.
If you use Windows Vista, click 
Start → All programs → 
Accessories → Run, and type X:\Setup.exe.
If the 
AutoPlay window appears in  Windows Vista, click 
Run Setup.exe in Install or run program field, and 
click 
Continue in the User Account Control window.
3Click Next. 
• If necessary, select a langua ge from the drop-down list.
4Select Typical installation for a network printer. Click 
Next.
5The list of printers available on the network appears. 
Select the printer you want to install from the list and then 
click 
Next. 
• If you do not see your printer on the list, click 
Update to 
refresh the list, or select 
Add TCP/IP Port to add your 
printer to the network. To  add the printer to the 
network, enter the port name and the IP address for the 
printer.
To verify your printer’s IP  address or the MAC address, 
print a Network Configuration page in machine.
• To find a shared network printer (UNC Path), select 
Shared Printer [UNC] and enter the shared name 
manually or find a shared  printer by clicking the 
Browse 
button.
NOTE:  If you cannot find your  machine in network, please 
turn off the firewall and click 
Update.
For Windows operating system, click 
Start → Control Panel  
and  start windows firewall, and set this option unactivated. 
For other operating system, refer to its on-line guide.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
9
6After the installation is finished, a window appears asking 
you to print a test page and to register yourself as a user 
of Samsung Printers in order to receive information from 
Samsung. If you so desire, select the corresponding 
checkbox(es) and click 
Finish.
Otherwise, just click 
Finish.
NOTE: After setup is complete, if your printer driver doesn’t 
work properly, reinstall the printer driver. See “Reinstalling 
Printer Software” on page 11.
Custom Installation
You can choose individual components to install and set a 
specific IP address.
1Make sure that the printer is connected to your network 
and powered on. For details about connecting to the 
network, see the supplied printer’s User’s Guide.
2Insert the supplied CD-ROM into your CD-ROM drive.
The CD-ROM should automaticall y run, and an installation 
window appears.
If the installation window does not appear, click 
Start and 
then 
Run. Type X:\Setup.exe, replacing “X” with the 
letter which represents your drive and click 
OK.
If you use Windows Vista, click 
Start → All programs → 
Accessories → Run, and type X:\Setup.exe.
If the 
AutoPlay window appears in  Windows Vista, click 
Run Setup.exe in Install or run program field, and 
click 
Continue in the User Account Control window.
3Click Next. 
• If necessary, select a language from the drop-down list.
4Select Custom installation. Click Next.
5The list of printers available on the network appears. 
Select the printer you want to install from the list and then 
click 
Next. 
• If you do not see your printer on the list, click 
Update to 
refresh the list, or select 
Add TCP/IP Port to add your 
printer to the network. To  add the printer to the 
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
10
network, enter the port name and the IP address for the 
printer.
To verify your printer’s IP address or the MAC address, 
print a Network Configur ation page in machine.
• To find a shared network printer (UNC Path), select 
Shared Printer [UNC] and enter the shared name 
manually or find a shared printer by clicking the 
Browse 
button.
NOTE: If you cannot find your mach ine in network, please turn 
off the firewall and click 
Update.
For Windows operating system, click 
Start → Control Panel  
and  start windows firewall, and set this option unactivated. 
For other operating system, refer to its on-line guide.
TIP: If you want to set a specific IP address on a specific 
network printer, click the 
Set IP Address button. The Set IP 
Address window appear s. Do as follows:
a. Select a printer to be set with a specific IP address from the  list.
b. Configure an IP address, su bnet mask, and gateway for the 
printer manually and click
 Configure to set the specific IP 
address for the network printer.
c. Click Next.
6Select the components to be  installed. After selecting the 
components, the following wind ow appears. You can also 
change the printer name, set the printer to be shared on 
the network, set the printer  as the default printer, and 
change the port name of each printer. Click 
Next.
To install this software on a server, select the 
Setting up 
this printer on a server
 checkbox.
7After the installation is fini shed, a window appears asking 
you to print a test page and to register yourself as a user 
of Samsung Printers in order to receive information from 
Samsung. If you so desire,  select the corresponding 
checkbox(es) and click 
Finish.
Otherwise, just click 
Finish.
NOTE: After setup is complete, if your printer driver doesn’t 
work properly, reinstall the printer driver. See “Reinstalling 
Printer Software” on page 11.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
11
Reinstalling Printer Software
You can reinstall the software if installation fails.
1Start Windows.
2From the Start menu select Programs or All Programs 
→ your printer driver name → Maintenance.
3Select Repair and click Next.
4The list of printers available on the network appears. 
Select the printer you want to install from the list and then 
click 
Next. 
• If you do not see your printer on the list, click 
Update to 
refresh the list, or select 
Add TCP/IP Port to add your 
printer to the network. To add the printer to the 
network, enter the port name and the IP address for the 
printer.
• To find a shared network printer (UNC Path), select 
Shared Printer [UNC] and enter the shared name 
manually or find a shared printer by clicking the 
Browse 
button.
You will see a component list so that you can reinstall any 
item individually.
NOTE: If your printer is not already connected to the 
computer, the following window will appear.
• After connecting the printer, click 
Next.
• If you don’t want to connect the printer at this time, click 
Next, and No on the following screen.  Then the installation 
will start and a test page will not be printed at the end of the 
installation.
• The reinstallation window that appears in this User’s  Guide may differ depending on the printer and 
interface in use.
5Select the components you want to reinstall and click 
Next.
If you installed the printer software for local printing 
and 
you select your printer driver name, the window 
asking you to print a test page appears. Do as follows:
a. To print a test page, select the check box and click 
Next.
b. If the test page prints out correctly, click Yes.
If it doesn’t, click 
No to reprint it.
6When the reinstallation is done, click Finish.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
12
Removing Printer Software
1Start Windows.
2From the Start menu select Programs or All Programs 
→ your printer driver name → Maintenance.
3Select Remove and click Next.
You will see a component list so that you can remove any 
item individually.
4Select the components you want to remove and then click 
Next.
5When your computer asks you to confirm your selection, 
click 
Yes.
The selected driver and all of its components are removed 
from your computer.
After the software is removed, click 
Finish.
Installing mono printer driver
This printer provides you the printer drivers with a mono driver 
so you can use your printer as  a monochrome printer. You must 
install the mono driver on your computer. Following steps guide 
you through the step by st ep installation process.
1Make sure that the printer is  connected to your computer 
and powered on. Or your computer and printer are 
connected to the network.
2Insert the supplied CD-ROM into your CD-ROM drive. The 
CD-ROM should automatically run, and an installation 
window appears.
3Click Cancel. 
If the confirmation window  appears, click Finish.
4Click Start → Printers and Faxes.
5Select Add Printer.
6When Add Printer Wizard appears, click Next.
7Select Local printer attached to this computer, and 
Automatically detect and install my Plug and Play 
printer
, then click Next. Go to step 13.
If your computer does not find  the printer, then follow the 
next step.
8Select Next in the Select a Printer Port window.
9In the Select a Printer Port window, select Have Disk....
10Click Browse to find a mono driver for your printer.
ex) Windows XP 32 bit
Select CD-ROM drive 
→ Printer → PC_MONO → 
WINXP_2000_VISTA-32
11Select ***.inf file and click Open.
12Click OK in the Install From Disk window.
13Select a mono driver in the Printers field, and click Next.
Downloaded From ManualsPrinter.com Manuals 
						

							
Installing Printer Software in Windows
13
NOTE: If you have installed a mono driver before, then the 
Use Existing Driver window. Select as the window explains, 
and click 
Next. Also, depending on your computer 
configuration, the printer sharin g window or the print the test 
page window may appear; make the appropriate selection.
14Enter your printer name, and click Next.
15Click Finish to start installing a mono printer driver.
NOTE: If your printer is connected to a network, go to 
printers 
Properties and select the Ports tab, then click Add 
Port
and Standard TCP/IP Port, and create a new port to 
connect to the printer. To  create a new port, follow the 
procedure laid out in the wizard window.
Downloaded From ManualsPrinter.com Manuals