Xerox 700 Digital Color Press User Manual

							
User Guide7-21
Xerox 700 Digital Color Press
Maintenance
Return the R1-R4 handle to the original position and close 
the front door. Push in the Drum Drawer completely. Return the Release 
Handle to its original position.
Insert the used charge corotron into an empty container 
for recycling.
That completes the procedure for replacing the Charge 
Corotron.  
Grasp the amber-gold colored casings on the new charge 
corotron and pull towards the front of the machine until 
you hear a clicking noise to indicate the charge corotron is 
in place. 
This procedure shows you how to remove the used Waste 
Toner Container and replace it with a new Waste Toner 
Container. The machine will tell you when you need to 
order a new Container and when to install it. Make sure the machine has stopped running, and open 
the Front Door.Open the waste toner container cover, located to the right 
of the Area #2 lever.
Replacing the Waste Toner Container
1.
2. 9.
10.
11.
12.
Downloaded From ManualsPrinter.com Manuals 
						

							
User Guide
7-22
Maintenance
Xerox 700 Di
gital Color Press
Hold the used waste toner container firmly with both hands and put it in\
to the provided plastic bag.
 
Hold the center part on the top of the container, and then 
remove it.
Grip the handle of the waste toner container and pull out 
about half of it.
 
Hold the center part on the top of a new container and insert it until i\
t comes to a stop.
 
Close the waste toner container cover.
 
Close the front cover door.
  CAUTION:
Never use a vacuum cleaner when you clean spilled toner. It can cause ex\
plosion as the toner fills the vacuum 
cleaner and gets sparks. Use a broom or a cloth moistened with a neutral\
 detergent.
 
3.
4.
5.
6.
7.
8.
Downloaded From ManualsPrinter.com Manuals 
						

							
User Guide7-23
Xerox 700 Digital Color Press
Maintenance
The hole punch waste container is a catch tray that 
contains the waste drilled paper.  Your machine will prompt 
you when the hole punch waste container needs emptying. 
When pulling the punch scrap container out to dispose the 
punch scraps, ensure that all scraps are discarded. If there 
are scraps remaining, the container may be full before the 
next message is displayed. It may cause machine 
malfunctions.
This procedure shows you how to empty the hole punch 
waste container.
Make sure that the machine has stopped, and open the 
front cover of the finisher.
Emptying the Punch Scrap Container
1. Pull out the punch scrap container.
2. Dispose of the drilled paper scraps into the waste  bin.
3. Install the emptied hole punch waste container,  ensuring that the container is inserted correctly.
That completes the procedure for emptying the hole 
punch waste container.
Downloaded From ManualsPrinter.com Manuals 
						

							
User Guide
7-24
Maintenance
Xerox 700 Di
gital Color Press
The Staple Waste Container should be emptied on a daily basis to ensure \
optimum operating efficiency of the digital 
press.
Emptying the Staple Waste Container
2. 1. Make sure that the machine has stopped copying and printing, then open t\
he Right Cover 
on the finisher.
Locate the Staple Waste Container (R5) in the finisher.
4. 3. Remove the container from the finisher.
6. 5. Remove the new container from the packaging. Dispose of the full contain\
er in  the new container packaging.
Insert the new container into the finisher. Grip the container and move the lever to the right; the Unlock position.\
4
5
1
3
6
8. 7. Move the lever to the left; the lock position. Close the Right Cover of the finisher.
Downloaded From ManualsPrinter.com Manuals 
						

							
User Guide8-1
1
2
3
5
4
8
7
9
6
1
2
3
4
5
6
7
8
9
The machine has designated paper jam clearance areas which are highlight\
ed in the above figure. If a paper jam 
occurs, a fault screen opens displaying a message stating in which area \
the jam is situated. The following steps show 
how paper jams are cleared in these areas.
Problem Solving
Jam Clearance
Paper Jams
Bypass Tray (Tray 5) Jam Clearance Tray 6 (HCF) Jam ClearanceTray 6/Tray 7 (OHCF) Jam Clearance Transfer Module/Fuser Document Feeder
Output Tray
Inverter (Bottom Right Cover)
Paper Trays
Bottom Left Cover
Downloaded From ManualsPrinter.com Manuals 
						

							
Problem Solving
User Guide
8-2 Xerox 700 Di
gital Color Press
This section describes how to clear paper jams that occur in the 
Document Feeder.
Document Feeder
2. 1. Open the Document Feeder Top Cover until it comes to a 
stop.
Open the Left Cover until it comes to a stop.
4. 3. If the document is not caught in the document feeder,  pull out the document.
Lift the handle and open the Inner Cover. Remove the 
jammed document.
Downloaded From ManualsPrinter.com Manuals 
						

							
Problem Solving
User Guide 8-3
Xerox 700 Digital Color Press
6. 5. Close the Inner Cover.
Close the Top Cover until it clicks into place.
Close the Left Cover until it clicks into place.
If the document cannot be found, raise the Document 
Feeder slowly.
Pull the handle and remove the document. The return the 
handle to its original position and close the Document 
Feeder.
8. 7. If the document is still not found, lift the Document  Feeder Tray and remove the document.
Gently return the Document Feeder Tray to its original 
position.
Make sure that the document is not torn, wrinkled or 
folded, and load the document again following the 
instructions displayed on the screen.
Downloaded From ManualsPrinter.com Manuals 
						

							
8-4User Guide
Problem Solvin
gXerox 700 Digital Color Press
This section describes how to clear paper jams that occur in the 
Transfer Module and Fuser area. 
Transfer Module and Fuser Jam Clearance
1. Open the Bottom Right Cover and tear off Lead Edge of 
any jammed sheet. Also, clear any jammed sheets from 
the Bypass (Tray 5) feeder.  Then, open the Front Door.
2. Turn Handle 2 to the right until it is in the horizontal  position, then pull out the transfer module.
3. Warning: Never touch a labeled area (found on the fuser  unit or nearby) indicating “High Temperature” and 
“Caution”. You may get burned.
Remove the visible jammed paper.
After clearing the jammed sheet, check to see that no 
torn paper pieces are left in the machine and then run 5 
blank sheets to clean left over toner from the Fuser roll.
4.
Downloaded From ManualsPrinter.com Manuals 
						

							
8-5
User Guide Problem Solving
Xerox 700 Digital Color Press
5. Move Handle 2a to the right and remove any jammed 
paper.
6. Pull down Handle 2b and remove the jammed paper.
7. Return Handle 2a and Handle 2b to their original  position. Push in the transfer module completely and turn 
Handle 2 to the left.
8. Close the front cover.
Downloaded From ManualsPrinter.com Manuals 
						

							
8-6User Guide
Problem Solvin
gXerox 700 Digital Color Press
This section describes how to clear paper jams that occur in 
Paper Trays 1 to 3.
Tray 1-3 Jam Clearance
1. Open the tray where the paper jam occurred.
2. Remove the jammed paper.
3. Push the tray in gently until it comes to a stop.
Paper is sometimes torn and remains inside the machine 
if you open a tray without checking the paper jam 
position. This may cause machine malfunction. Check 
where the paper jam occurred before clearing the 
problem.
Note
Downloaded From ManualsPrinter.com Manuals