Xerox 700 Digital Color Press User Manual

							
10-15
User Guide Addendum
Xerox 700 Digital Color Press
Fault code Possible cause Recommended solution
049 280
049 281
049 282
049 283
049 284 Senor problem/failure Power off, then power on
049 285
049 286 EEPROM error
Power off, then power on
049 287 System error Power off, then power on
049 288 Main PWB and Driver PWB are  disconnected Power off, then power on
049 300 Upper cover is open Close the upper cover
049 310 HCS download mode failure Power off, then power on
049 700 Error in stacking the output  paper/media Remove the paper from the stacker tray
049 940 Front door is open Close the front door
049 941 UI indicates the Stacker Cart and/or  Tray needs to be reset Press the Unload button. The Wait light blinks until the 
Stacker Tray has reached the down position.
1.
2.
3.
4. When the Stacker Tray has reached the down position, 
open the front door.
Position the Stacker Cart securely into the HCS.
Close the front door.
Downloaded From ManualsPrinter.com Manuals 
						

							
10-16User Guide
Xerox 700 Digital Color Press
Addendum
Fault code Possible cause Recommended solution
049 945 The UI displays a message indicating  that the Top Tray is full. Remove all the paper from the Top Tray.
049 960
049 961
049 962
049 963
049 964
049 967
049 969
049 970
049 971
049 972 The UI displays the following message, 
"Take out the paper stack." Press the Unload button. The Wait light blinks until the 
Stacker Tray has reached the down position.
1.
2.
3.
4. When the Stacker Tray has reached the down position, 
open the front door.
Remove the Stacker Cart.
Remove all the stacked paper.
5. Position the Stacker Cart securely into the HCS.
6. Close the front door.
7. Power off, then power on
Downloaded From ManualsPrinter.com Manuals 
						

							
10-17
User Guide Addendum
Xerox 700 Digital Color Press
If power is interrupted to the HCS:
Ensure the power cord is plugged in to the proper wall receptacle
•
Ensure that the machine power is switched “On”
•
Ensure that the Ground Fault Indicator is in the "On" position
•
If the power has not been restored by checking the above items, then cal\
l for service
•
Loss of power
Paper guidelines
Specifications
Stacker Tray will accept 64-280 gsm (either coated or uncoated stock) \
with the possibility of degraded stock 
•
quality and increased jam rate
Transparencies may be run to either the Top Tray or the Stack Tray. Stac\
k height should be limited to 100 
•
transparencies.
Coated paper lighter than 100 gsm may not run as reliably as coated pape\
r heavier than 100 gsm. 
•
Non-standard papers longer than 305 mm (12in.) in the feed direction r\
equire 210 mm (8.3in.) minimum 
•
measurement across the feed direction.
Non-standard papers shorter than 254 mm (10”) in the cross-feed dir\
ection require 330 mm (13”) minimum 
•
measurement in the feed direction.
Electrical
100V to 240V
Frequency: 50/60 Hz
Temperature and humidity
10 to 32°C, 15 to 85RH
50 to 90°F, 15 to 85RH
Downloaded From ManualsPrinter.com Manuals 
						

							
10-18User Guide
Xerox 700 Digital Color Press
Addendum
Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals 
						

							Downloaded From ManualsPrinter.com Manuals