Canon printer PIXMA MG2920 white User Manual

							(8) operation panelUse to change the settings of the machine or to operate it.
Operation Panel
(9) platen glass Load an original here.
91 
						

							Rear View
(1) power cord connectorPlug in the supplied power cord.
(2) USB port Plug in the USB cable to connect the machine with a computer.
Important
•
Do not touch the metal casing.
•
Do not plug in or unplug the USB cable while the machine is printing or scanning originals with thecomputer.
92 
						

							Inside View
(1) FINE cartridge (ink cartridges)A replaceable cartridge that integrates print head and ink tank.
(2) FINE cartridge holder Install the FINE cartridge.
The color FINE cartridge should be installed into the left slot and the black FINE cartridge should be
installed into the right slot.
Note
•
For details on replacing a FINE cartridge, see Replacing a FINE Cartridge .
Important
•
The area around the parts (A) may be splattered with ink. This does not affect the performance of the
machine.
•
Do not touch the parts (A). The machine may not print properly if you touch them.
93 
						

							Operation Panel* All lamps on the operation panel are shown lit in the figure below for explanatory purposes.
(1) ON button Turns the power on or off. Before turning on the power, make sure that the document cover is closed.
Turning the Machine On and Off
(2) ON lamp Lights after flashing when the power is turned on.
Note
•
You can check the status of the machine by the  ON and  Alarm  lamps.
•
ON lamp is off: The power is off.
•
ON lamp lights: The machine is ready to print.
•
ON lamp flashes: The machine is getting ready to print, or printing is in progress.
•
Alarm  lamp flashes: An error has occurred and the machine is not ready to print.
•
ON lamp flashes and  Alarm lamp flashes alternately: An error that requires contacting the service
center may have occurred.
If an Error Occurs
(3) Wi-Fi button Hold down to automatically set up the wireless LAN connection.
(4) Wi-Fi lamp Lights or flashes to indicate the wireless LAN status.
Lights: Wireless LAN connection is enabled.
Flashes: Printing or scanning over wireless LAN. Also flashes while configuring the wireless LANconnection.
94 
						

							(5) Alarm lampLights or flashes when an error occurs. When performing machine maintenance or machine settings,
options can be selected according to the number of flashes.
(6) ink lamps Light or flash when ink runs out, etc.
The upper lamp indicates the black FINE cartridge status, the lower lamp the color FINE cartridge status.
(7) Stop button Cancels operations. You can press this button to cancel a print, copy, or scan job in progress. Holding
this button down lets you select maintenance options or machine settings.
(8) Black button* Starts black & white copying. You can also press this button to finalize your selection for the setting
item.
(9) Color button* Starts color copying. You can also press this button to finalize your selection for the setting item.
* In the software applications or manuals, the  Color and Black  buttons are collectively called the "Start" or
"OK" button.
95 
						

							About the Power Supply of the Machine
Confirming that the Power Is On
Turning the Machine On and Off
Notice for the Power Plug/Power Cord
Notice for Unplugging the Power Cord
96 
						

							Confirming that the Power Is OnThe  ON lamp is lit when the machine is turned on.
Note
•
It may take a while for the machine to start printing immediately after you turn on the machine.
97 
						

							Turning the Machine On and OffTurning on the machine1.
Press the  ON button to turn on the machine.
The  ON lamp flashes and then remains lit.
Confirming that the Power Is On
Note
•
It may take a while for the machine to start printing immediately after you turn on the machine.
•
If the  Alarm  lamp lights up or flashes, see If an Error Occurs .
•
You can set the machine to automatically turn on when a print or scan operation is performed
from a computer connected by USB cable or wireless network. This feature is set to off by
default. For details on the auto power on feature, see below.
From the machine
Turning on/off the Machine Automatically
From the computer
Managing the Printer Power
Turning off the machine
1.
Press the  ON button to turn off the machine.
When the  ON lamp stops flashing, the machine is turned off.
Important
•
When you unplug the power cord  after turning off the machine, be sure to confirm that the  ON
lamp is off.
98 
						

							Note•
You can set the machine to automatically turn off when no operations are performed or no print
jobs are sent to the machine for a certain interval. This is the default setting. For details on the
auto power off feature, see below.
From the machine
Turning on/off the Machine Automatically
From the computer
Managing the Printer Power
99 
						

							Notice for the Power Plug/Power CordUnplug the power cord once a month to confirm that the power plug/power cord does not have anythingunusual described below.•
The power plug/power cord is hot.
•
The power plug/power cord is rusty.
•
The power plug/power cord is bent.
•
The power plug/power cord is worn.
•
The power plug/power cord is split.
Caution
•
If you find anything unusual with the power plug/power cord described above, unplug the power cord
and call for service. Using the machine with one of the unusual conditions above may cause a fire or an
electric shock.
100