Canon printer PIXMA MG2920 white User Manual

							1688Cause
The ink has run out.
Action
Replace the ink cartridge and close the cover.
If printing is in progress and you want to continue printing, press the machine's  Stop button for at least 5
seconds with the ink cartridge installed. Then printing can continue under the ink out condition.
The function for detecting the remaining ink level will be disabled.
Replace the empty ink cartridge immediately after the printing. The resulting print quality is not
satisfactory, if printing is continued under the ink out condition.691 
						

							168ACauseThe FINE cartridge is not installed properly, or the FINE cartridge not compatible with this machine isinstalled.
Action Retract the output tray extension and the paper output tray, open the cover, then remove the FINEcartridges.
Make sure that the FINE cartridge compatible with the machine is installed.
Then install the FINE cartridges again. Push up the FINE cartridge until it clicks into place.
After installing, close the cover.
692 
						

							1700Cause
The ink absorber is almost full.
Action Press the machine's  Black or Color  button to continue printing. Contact the service center.693 
						

							1701Cause
The ink absorber is almost full.
Action Press the machine's  Black or Color  button to continue printing. Contact the service center.694 
						

							1890Cause
The protective material for the FINE cartridge holder or the tape may remain attached to the holder.
Action Make sure that the protective material or the tape does not remain attached to the FINE cartridge holder.
If you find the protective material or the tape remains attached, retract the output tray extension and the
paper output tray to remove the protective material or the tape.
Pull down the tape to remove the protective material.
If the cover is open, close it.
If the problem is not resolved, contact the service center.
695 
						

							2900Cause
Scanning the print head alignment sheet has failed.
Action Press the machine's  Black or Color  button to dismiss the error. Check the following points, perform
Automatic Print Head Alignment again.•
Make sure that the print head alignment sheet is set in the correct position and orientation on the platen glass.
•
Make sure the platen glass and the print head alignment sheet are not dirty.
•
Make sure the type and size of loaded paper is suitable for Automatic Print Head Alignment.
For Automatic Print Head Alignment, always load one sheet of A4 or Letter-sized plain paper.
•
Make sure if print head nozzles are clogged.
Print the nozzle check pattern to check the status of the print head.
If the error is not resolved, perform Manual Print Head Alignment.
696 
						

							2901Cause
Printing of the print head alignment pattern is complete and the machine is in waiting for scanning the
sheet.
Action
Proceed to scan the printed alignment pattern.1.
Load the print head alignment sheet on the platen glass.
Load the print head alignment sheet with the printed side facing down and align the mark 
 on the
upper left corner of the sheet with the alignment mark 
.
2.
Close the document cover gently, then press the machine's  Black or Color  button.
The machine starts scanning the print head alignment sheet, and the print head position will be
adjusted automatically.
697 
						

							4100Cause
The specified data cannot be printed.
Action When you print the contents on CREATIVE PARK PREMIUM, confirm the message on the computer
screen, make sure that genuine Canon FINE cartridges are all installed properly, then start printing again.698 
						

							4102Cause
The media type and paper size are not set correctly.
Action Press the machine's  Stop button to cancel printing, change the media type or paper size setting, then
print again.•
When the media type is set to  Photo Paper Plus Glossy II:
Set the paper size to  4"x6" 10x15cm (Windows)/4 x 6 (Mac), or  5"x7" 13x18cm  (Windows)/5 x 7
(Mac).
•
When the media type is set to  Glossy Photo Paper:
Set the paper size to  4"x6" 10x15cm (Windows)/4 x 6 (Mac).
•
When the media type is set to  Envelope:
Set the paper size to  Envelope Com 10 (Windows)/Envelope #10  (Mac) or Envelope DL  (Windows/
Mac).
699 
						

							4103Cause
Cannot perform printing with the current print settings.
Action Press the machine's  Stop button to cancel printing.
Then change the print settings and print again.700