Oce ColorWave 600 User Manual

							Calibrate the Océ ColorWave 600 printer
When to do
Note:
Only roll position 1 can be used for calibrations.
Note:
Use only Océ 'Media' for reliable calibrations.
Note:
The printer will do the calibration automatically. You do not need to keep this printed
calibration chart. Evaluate the Customer Acceptance 
Test print. If the print shows any output quality
problems, 
you can use this calibration wizard to check if the Océ ColorWave 600 works
properly. The 
calibration will take a several minutes. The printed output is delivered at the rear
side 
of the printer and lead through the slot below the 'Top back cover'.
Attention:
If a copy delivery tray is installed, remove the copy delivery tray from the engine and re-
move the copy delivery tray data cable from the controller before starting the calibration.
Attention:
If a folder is installed, make sure that the folder is switched ON and lift the bridge before
starting the calibration. Chapter 8
 - Print quality and Print productivity 381Calibrate the Océ ColorWave 600
 printer
Downloaded From ManualsPrinter.com Manuals 
						

							How to calibrate the Océ ColorWave 600 printer
#
Remarks
Action
Step From the 'Home' screen on the printer operator panel
select the 'System' tab.
1 Select the 'Maintenance' tab with the upper left softkey.
2 Use 
the 'Scroll wheel' to select 'Calibration' and con-
firm with
 
the 'Confirmation key' (above the 'Scroll
wheel').
3 The 
wizard assists you to do a calibration.
Press 'Next'
 to start 
the calibration. 4
Chapter 8
 - Print quality and Print productivity382Calibrate the Océ ColorWave 600
 printer
Downloaded From ManualsPrinter.com Manuals 
						

							Remarks
Action
Step Now you can select:
• paper transport
• full
 calibration
Press 'Next' to start 
the calibration.
5 Press 'Finish' to 
continue.
Note:
If the calibration failed, you will be informed
immediately through
 an error-code on the
'Printer operator

 panel'. 6
Select 'System'.
7 Select 'Home' to return to the 'Home' screen.8
Chapter 8
 - Print quality and Print productivity 383Calibrate the Océ ColorWave 600
 printer
Downloaded From ManualsPrinter.com Manuals 
						

							Remarks
Action
Step 'Home' screen.
9
Result Evaluate the
 Customer Acceptance 
Test print. Check if the print does not show any of
the
 following output quality problems:
• ‘Banding 
across the print with differences in color and gloss’  on page 375
• ‘Horizontal, wavy
 lines across your print’  
on page 377
• ‘Thin horizontal,
 coloued or white lines across your print’  
on page 379If no output quality problems occur, the installation procedure is finished and your Océ
ColorWave 600 
is ready for use.
Chapter 8
 - Print quality and Print productivity384Calibrate the Océ ColorWave 600
 printer
Downloaded From ManualsPrinter.com Manuals 
						

							Calibration error codes
Introduction
Before or during the calibration, it is possible that the calibration failed. In that case, you
will be informed immediately through an error code on the 'Printer operator panel'.
Attention:
Error-codes are only displayed at the 'Printer operator panel'. If an error code is displayed
that is not related to the calibration process, the user must follow the instructions on the
printer operator panel to solve 
the problem.
Note:
For feedback about errors related to the processing of print jobs open the event list in
the 'Jobs'
 tab. Overview calibration error codes
#
Remarks
Action
Error-code
Roll 
not loaded
Calibration not accepted:
22917
Roll 
too small
Calibration not
 accepted:
22918
Media type not suitable for instal-
lation 
calibrations
Calibration not accepted:
22919
Media
 type not suitable for Y-
alignment
Calibration not

 accepted:
22920
Media type not suitable for pa-
per step

 calibration
Calibration not

 accepted:
22921
External
 output not available for
delivery
Calibration not accepted:
22922
Printer
 engine status is not
standby or

 the folder (if config-
ured) 
is offline or turned off
Calibration
 not accepted:
22923
Out
 of toner during calibrations
Calibration failed:
22924
Out 
of media during calibrations
Calibration failed: 22925
Chapter 8
 - Print quality and Print productivity 385Calibration error codes
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 8 - Print quality and Print productivity386Calibration error codes
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 9
License 
management
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction to managing licenses
Introduction
The Océ applications and options are protected against unauthorized use. You need to
activate
 the license to enable an application or option for use. The 
'Support' - 'Licenses'
tab 
in the Océ Express WebTools enables you to manage the licenses very easily.
This
 
section describes the following.
• The 
basic concept of the licenses.
• How to manage the licenses.
Chapter 9
 - License management388Introduction to managing licenses
Downloaded From ManualsPrinter.com Manuals 
						

							The 'Licenses' tab in the Océ Express WebTools
Introduction
The 'Support' - 'Licenses' tab has the following possibilities.
Possibilities •View 
the current active licenses
• Get
 the host id 
of the Océ system
• Save
 
the active licenses
• You can activate new licenses or saved licenses.
Chapter 9
 - License management 389The 'Licenses' tab in the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							The basic workflow of 'Support' - 'Licenses' activation
Introduction Before you can 
work with licenses, you must access to the Océ Express WebTools. The
following
 workflow describes per step when to 
use which possibility.
The 
workflow 1. View 
the current active licenses.
You
 can make 
a list of new options you need and make a list of license numbers. Océ
needs the
 list of new options and the license numbers to create a new license file.
2. Get the

 host id 
of the Océ system.
Océ
 
needs the host id of your Océ system to create a new license file.
3. Send 
the list of new options you need, the list of license numbers and the host id to Océ.
Océ creates 
and delivers one or more new license files.
4. Create a
 back-up of the current active licenses if necessary.
Save

 
the current active licenses to do so.
5. Activate the
 licenses.
The 
license activation job guides you through the following steps.
• 1.
 Locate the license file
• 2.
 Preview the new active licenses
• 3.
 Accept the end user license agreement
• 4.
 Finish the license activation job
• 5.
 Restart the Océ system.
Chapter 9
 - License management390The basic workflow of 'Support' -
 'Licenses' activation
Downloaded From ManualsPrinter.com Manuals