Oce ColorWave 600 User Manual

							6.
Once logged in, enter the printer 'Host name' (for example: OceColorWave600) in the
'Identification'
 window, in order to address the Océ ColorWave 600 by its 'Host name'.
You can

 
define the other settings if needed. Restart is required. 7.
Turn 
the printer off and on to restart the Océ ColorWave 600 printing system.
8. Wait until
 the system is ready again.
9. Enter the

 following address: 'http://' (for example
http://OceColorWave600)
 in the workstation web browser:
If the

 Océ Express WebTools appear the printer is integrated in the network and ready
for use. If an error page ('Page cannot be displayed') appears, contact the network administrator.
Check the Host name and the other web browser security and network settings.
Chapter 3
 - Prepare the printing system for use and get started 81Complete the printer configuration in the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							Refer to the Océ TDS/TCS Connectivity Manual, 'Chapter 2 - Windows TCP/IP envi-
ronment' to
 find 
technical information about the Océ ColorWave 600 integration in a
network 
environment. Chapter 3
 - Prepare the printing system for use and get started82Complete the printer configuration in the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							Configure the regional settings of the Océ ColorWave 600
Purpose
The regional settings are configured during the installation of your Océ ColorWave 600.
If you want to change the initial configuration, you can do so in the 'Regional settings'.
Define
 the regional settings for the printer in the following order.
• 'First 
language' and 'Second language' of the printer operator panel
• 'Measurement unit'
• 'Time 
zone'
If you change the 'Time zone' 
you must first reboot the system, before you set the
'Current date
 and time'.
• 'Current date

 and time'
• 'Time 
format'
Note:
Every time you change the 'Measurement unit', the controller recalculates the values
from 
millimeter to inches and vice versa. If you reverse to the original value of this setting
a slight calculation difference can occur due to rounding differences. How to define the regional settings
1.Select 'Preferences' - 'System properties'.
2. Click 
'Edit' in the 'Regional settings' bar or click the value of the setting you want to
edit, for example 'First language'.
3. Modify

 the settings. You can choose 
between:
• settings that are 
commonly used in the USA
• or settings
 that are 
commonly used in the rest of the world.
4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 3
 - Prepare the printing system for use and get started 83Configure the regional settings of the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 
						

							Print the Customer Analysis Tool (CAT) demo print
When to do
When you have installed the printer and prepared the printer for use, you can print the
Customer 
Analysis Tool demo print. You can use this demo print to check if the Océ
ColorWave 600 
works correctly.
How 
to print the Customer Analysis Tool (CAT) demo print #
Illustration
Action From the 'Home' screen on the printer operator panel
select 
the 'System' tab.
1 Select the 'Maintenance' tab with the upper left softkey.
2 Use the 'Scroll wheel' to select 'Demo print' and con-
firm with the 'Confirmation key' (above the 'Scroll
wheel').3
Chapter 3
 - Prepare the printing system for use and get started84Print the Customer Analysis Tool (CAT) demo print
Downloaded From ManualsPrinter.com Manuals 
						

							Illustration
Action Use the 'Scroll wheel' to select 'Customer Analysis
Tool'.
4 Press 'Finish' to 
print the 'Customer Analysis Tool'
demo print.
5 Select 'Back' and 'Home' to return to the 'Home'
screen.
6
Result Evaluate 

the 'Customer Analysis Tool' demo print. Check if the print does not show any
of the following output quality problems:
• ‘Banding 
across the print with differences in color and gloss’  on page 375
• ‘Horizontal, wavy
 lines across your print’  
on page 377
• ‘Thin horizontal,
 coloued or white lines across your print’  
on page 379If no output quality problems occur, the installation procedure is finished. Your Océ
ColorWave 600 
is now ready for use.
Chapter 3
 - Prepare the printing system for use and get started 85Print the Customer Analysis Tool (CAT) demo print
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 3 - Prepare the printing system for use and get started86Print the Customer Analysis Tool (CAT) demo print
Downloaded From ManualsPrinter.com Manuals 
						

							Chapter 4
Configure 
the printing
system
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction to the Océ Express
WebTools
Purpose of the Océ Express WebTools
Definition
The Océ Express WebTools is an application that runs embedded on the Océ ColorWave
600.
This application gives you access to the settings to manage the configuration and prefer-
ences of the Océ ColorWave 600. To change settings in the Océ Express WebTools you
must log
 in using one of three predefined user roles because the settings are all password
protected. (see 
‘User roles and authorizations’  on page 110)
Illustration 'Jobs' tab
Editable for any user. For some specific actions you must log in as 
a Key operator.
Chapter 4
 - Configure the printing system88Purpose of the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							When you access the 'Jobs' tab you can see 3 different sections.
• The 
Océ Publisher Express section.
To submit
 a new job click 'Create new job'. A new window opens, where you can
define

 some basic job settings and where you can browse to the file you want to print.
• The 
'Jobs - Queue' section.
This
 
section gives an overview of the jobs in the queue, waiting to be printed. The
buttons on
 top of the 'Jobs - Queue' section allow you 
to move a selected job to the
top
 of the queue or to delete the job. If you click 'Delete all' all jobs are deleted from
the queue.
• The 
'Smart Inbox' section.
This 
section gives an overview of every 'Smart Inbox' that currently contains one or
more
 print jobs. You can select a print job in the Smart Inbox and use the buttons on
top 
of the Smart Inbox section to print, edit or delete the job.
When 
you click 'Open Smart Inbox' you can create a new Smart Inbox that immedi-
ately appears in the Smart Inbox section.
If 

you click 'Delete all' in the 'View all' Smart Inbox all jobs are deleted from all Smart
Inboxes.
Note:
The 'View all' Smart Inbox is only available if you enable the 'Preferences' - 'System
properties' -
 'Job management' - 'Display a view on all Smart Inbox jobs' setting. 'Preferences' tab
Editable for Key operator and Power user. (see  ‘User roles and authorizations’ on page 110
)
The 'Preferences' tab contains the default settings to fine tune the system to optimally fit
your 
company's workflow and processes. #
Groups
Tab
•'Overview'
Summary of the settings organised in different groups.
• 'System properties'
• 'Print job

 defaults'
'Preferences'
'Configuration' 

tab
Editable for System administrator and Power user. (see  ‘User roles and authorizations’ on
page 110 )
Chapter 4
 - Configure the printing system 89Purpose of the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							The 'Configuration' tab contains the settings to install the system in your infrastructure,
according to your standards. These settings are configured during installation and do not
need frequent adjustment.
#
Groups
Tab
•'Overview'
Summary of the settings organised in different groups.
• 'Connectivity'
• 'Printer setup'
'Configuration'
'Support' 

tab
Editable for System administrator and Power user. (see  ‘User roles and authorizations’ on
page 110 )
Chapter 4
 - Configure the printing system90Purpose of the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals