Ricoh B230 Service Manual

							 
SM 5-275 B230/B237 
Service 
Tables 
5913 [Switchover Permission Time] 
Print Application Timer  *CTL 
[3 to 30 / 3 / 1 second /step] 
002 Sets the amount of time to elapse while the machine is in standby mode (and 
the operation panel keys have not been used) before another application can 
gain control of the display. 
 
5967 [Copy Server Set 
Function] *CTL 
 0: ON, 1: OFF 
 Enables and disables the document server. This is a security measure that 
prevents image data from being left in the temporary area of the HDD. After 
changing this setting, you must switch the main switch off and on to enable the 
new setting. 
 
[Cherry Server] 
5974 
Specifies which version of ScanRouter, “Lite” or “Full”, is installed. 
001 Cherry Server  *CTL
   [0 or 1 / 0 / – ] 
0: Lite 
1: Full 
 
[Device Setting] 
5985 The NIC and USB support features are built into the GW controller. Use this 
SP to enable and disable these features. In order to use the NIC and USB 
functions built into the controller board, these SP codes must be set to 1. 
001  On Board NIC [0 to 2 / 0 / 1 /step] 
0: Disable, 1: Enable, 2: Function limitation 
When the Function limitation is set, On board NIC is 
limited only for the NRS or LDAP/NT authentication. 
 
ƒ  Other network applications than NRS or 
LDAP/NT authentication are not available when  
						

							 
B230/B237 5-276  SM 
this SP is set to 2. Even though you can change 
the initial settings of those network applications, 
the settings do not work. 
002  On Board USB [0 or 1 / 0 / 1/step] 
0: Disable, 1: Enable 
 
5987 [Counter Falsification Prevention]  
 001  0: OFF / 1: ON This SP detects that a mechanical counter device is 
removed. If it is detected, SC610 occurs.  
ƒ  The mechanical counter is provided only for 
NA model. 
 
[SP print mode] 
5990 
Prints out the SMC sheets. 
001  All (Data List)  - 
002  SP (Mode Data List)  - 
003 User Program  -   
004 Logging Data  - 
005 Diagnostic Report  -   
006 Non-Default  - 
007 NIB Summary  - 
008 Capture Log  -   
021  Copier User Program  -    
022 Scanner SP  -   
023  Scanner User Program  -    - 
  
						

							 
SM 5-277 B230/B237 
Service 
Tables 
SP6-XXX (Peripherals) 
6006 [ADF Adj.] ADF Adjustment 
  Adjusts the side-to-side and leading registration of originals with the ARDF. 
001 Side-to-Side Registration 
[-3.0 to 3.0 / 0 / 0.1 mm/step ] 
003 Leading Edge 
Registration *ENG
[-5.0 to 5.0 / 0 / 0.1 mm/step ] 
 Adjusts the amount of paper buckle to correct original skew for the front and 
rear sides. 
005  Buckle: Duplex Front 
006  Buckle: Duplex Rear *ENG
[-5.0 to 5.0 / 0 / 0.1 mm/step ] 
  Adjusts the erase margin at the original trailing edge. 
007  Rear Edge Erase  *ENG
[-5.0 to 5.0 / 0 / 0.1 mm/step ] 
 
[ADF Input Check] 
6007 
Displays the signals received from the sensors and switches of the ARDF. 
Only Bit 0 is used for ADF input check. 
001 Original Length 1 (B5 
Detection Sensor) 
002 Original Length 2 (A4 
Detection Sensor) 
003 Original Length 3 (LG 
Detection Sensor) 
004  Original Width S 
005  Original Width M 
006  Original Width L 
007  Original Width LL 0: Paper not detected 
1: Paper detected  
						

							 
B230/B237 5-278  SM 
009 Original Detection 
010  Rear Edge Detection 
011 Skew Correction 
013 Registration 
014 Exit 
015 Feed Cover 0: ADF cover close 
1: ADF cover open 
016 Lift Up 0: ADF  close 
1: ADF  open 
 
[ADF Output Check] 
6008 
Activates the electrical components for functional check. 
It is not possible to activate more than one component at the same time. 
003  Feed Motor Forward  Feed Motor-Forward rotation 
004  Feed Motor Reverse  Feed Motor-Reverse rotation 
005  Relay Motor Forward  Transport Motor- Forward rotation 
006  Relay Motor Reverse  Transport Motor- Forward rotation 
009 Feed Clutch  - 
010  Feed Solenoid    Pick-up Solenoid 
011 Inverter Solenoid  - 
012 Stamp - 
Stamp Solenoid 
 
[ADF Free Run] 
6009 
Performs a DF free run in duplex mode or stamp mode. 
002  Free Run Duplex Motion  -  -  
						

							 
SM 5-279 B230/B237 
Service 
Tables 
 
[Stamp Position Adj.] Fax Stamp Position Adjustment 
6010 
Adjusts the horizontal position of the stamp on the scanned originals. 
6010 1  Stamp Position Adj.  *ENG
[-5.0 to 5.0 / 0 / 1 mm/step] 
 
[Original Size Detection Priority] Original Size Detection Priority 
6016 
Specifies the original size for a size detected by the original sensor, since 
original sensors cannot recognize all sizes. 
001 Original Size Detection 
Priority *ENG[0 or 1 / 0 / - ] 
0: Setting 1 
1: Setting 2 
Setting 1Setting 2 
Bit 7: A4 (L)/LT (L) 
Bit 6: 11 x 15/DLT (L) 
Bit 5: DLT (L)/ 11 x 15 
Bit 4: LT (S)/ US Exec (S) 
Bit 3: LT (L)/ 8 x 10 (L) 
Bit 2: LG (L)/ F4 (L) 
Bit 1: A4 (L)/ 16K (L) 
Bit 0: 8K (L)/ DLT (L) 
Bits used for detection differ depending on 
destination as shown below. 
Bit 7 to 6: Only for Japan 
Bit 5 to 2: Only for US 
Bit 1 to 0: Only for EU/AA 
 
[DF Magnification Adj.] DF Magnification Adjustment 
6017 
Adjusts the magnification in the sub-scan direction for the ARDF. 
001 DF Magnification Adj.  *CTL
[-5.0 to 5.0 / 0 / 0.1 %/step] 
 
6123 [Jogger Position Adj.]  
						

							 
B230/B237 5-280  SM 
Adjusts the jogger position. 
001 -  *ENG
[-4.0 to 4.0 / 0 / 0.4 mm/step] 
 
[Punch Position: Sub Scan] 
6128 
Adjusts the punching position in the sub scan direction. 
001 Domestic 2Hole  *ENG
002 North America 3Hole  *ENG
003 Europe 4Hole  *ENG
004  North Europe 4Hole  *ENG
005  North Europe 2Hole  *ENG[-7.5 to 7.5 / 0 / 0.5 mm/step]] 
 
[Punch Position: Main Scan] 
6129 
Adjusts the punching position in the main scan direction. 
001 Domestic 2Hole  *ENG
002 North America 3Hole  *ENG
003 Europe 4Hole  *ENG
004  North Europe 4Hole  *ENG
005  North Europe 2Hole  *ENG[-2.0 to 2.0 / 0 / 0.4 mm/step]] 
 
[Skew Correction: Buckle Adj.] 
6130 
Adjusts the paper buckle for each paper size. 
001 A3T (SEF)  *ENG
002 B4T (SEF)  *ENG
003 A4T (SEF)  *ENG[-5.0 to 5.0 / 0 / 0.25 mm/step]]  
						

							 
SM 5-281 B230/B237 
Service 
Tables 
004 A4Y (LEF)  *ENG
005 B5T (SEF)  *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF)  *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF)  *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18  *ENG
012 Other  *ENG
 
[Skew Correction Control] 
6131 
Selects the skew correction control for each paper size. These are only 
activated for B793. 
001 A3T (SEF)  *ENG
002 B4T (SEF)  *ENG
003 A4T (SEF)  *ENG
004 A4Y (LEF)  *ENG
005 B5T (SEF)  *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF)  *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF)  *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18  *ENG[0 to 2 / 1 / 1/step]] 
0: No (No skew correction) 
1: Roller Stop Skew Correction 
2: Roller Reverse Skew Correction  
						

							 
B230/B237 5-282  SM 
012 Other  *ENG
 
[Jogger Fence Fine Adj] 
6132 This SP adjusts the distance between the jogger fences and the sides of the 
stack on the finisher stapling tray in the Booklet Finisher B793. The adjustment 
is done perpendicular to the direction of paper feed. 
001 A3T (SEF)  *ENG
002 B4T (SEF)  *ENG
003 A4T (SEF)  *ENG
004 A4Y (LEF)  *ENG
005 B5T (SEF)  *ENG
006 B5Y (LEF)  *ENG
007 DLT-T (SEF)  *ENG
008 LG-T (SEF)  *ENG
009 LT-T (SEF)  *ENG
010 LT-Y (LEF)  *ENG
011  12 x 18  *ENG
012 Other  *ENG[-1.5 to 1.5 / 0 / 1/step] 
+ Value: Increases distance between 
jogger fences and the sides of the stack. 
- Value: Decreases the distance between 
the jogger fences and the sides of the 
stack. 
 
[Staple Position Adjustment] 
6133 Adjusts the staple position for each finisher (B408/B793/B792).  
+ Value: Moves the staple position to the rear side. 
- Value: Moves the staple position to the front side. 
001  Finisher 1 (B408/B793)  *ENG
[-3.5 to 3.5 / 0 / 1/step]] 
002  Finisher 2 (B792)  *ENG
[-2.0 to 2.0 / 0 / 1/step]] 
  
						

							 
SM 5-283 B230/B237 
Service 
Tables 
6134 [Saddle Stitch Position Adjustment] 
User 
SP Use this SP to adjust the stapling position of the booklet stapler when paper is 
stapled and folded in the Booklet Finisher B793. 
001 A3 SEF 
002 B4 SEF 
003 A4 SEF 
004 B5 SEF 
005 DLT-T (SEF) 
006 LG-T (SEF) 
007 LT-T (SEF) 
008  12 x 18 
009 Other [-3.0 to 3.0 / 0 / 0.2 mm/step] 
+ Value: Shifts staple position toward the crease. 
- Value: Shifts staple position away from the crease. 
 
 
6135 [Folder Position Adj.] 
User SP This SP corrects the folding position when paper is stapled and folded in the 
Booklet Finisher B793. 
001 A3 SEF 
002 B4 SEF 
003 A4 SEF 
004 B5 SEF 
005 DLT-T (SEF) 
006 LG-T (SEF) 
007 LT-T (SEF) 
008  12 x 18 [-3.0 to 3.0 / 0 / 0.2 mm/step] 
+ Value: Shifts staple position toward the crease. 
- Value: Shifts staple position away from the crease. 
  
						

							 
B230/B237 5-284  SM 
009 Other 
 
[Finisher Free Run] 
6137 
These SPs are used only for B793 finisher. 
001  Free Run 1  Free run for paper edge stapling. 
002  Free Run 2  Free run for booklet stapling. 
003  Free Run 3 Shipping free run. Simulates standby conditions during 
shipping. 
004  Free Run 4 
DFU 
 
6138 [FIN (TIG) INPUT Check] Finisher (B793) Input Check 
 Displays the signals received from sensors and switches of the booklet finisher. 
( Input Check Table) 
 
6139 [FIN (KIN) INPUT Check] Finisher (B408) Input Check 
 Displays the signals received from sensors and switches of the booklet finisher. 
( Input Check Table) 
 
6141 [FIN (KAN) INPUT Check] Finisher (B792) Input Check 
 Displays the signals received from sensors and switches of the booklet finisher. 
( Input Check Table) 
 
6143 [FIN (TIG) OUPUT Check] Finisher (B793) Output Check 
 Displays the signals received from sensors and switches of the booklet finisher. 
( Output Check Table) 
 
6144 [FIN (KIN) OUPUT Check] Finisher (B408) Output Check