Ricoh B230 Service Manual

							  
SM 1-39 B230/B237 
Installation 
 
1.  Install the two support brackets [A] on the left side of the machine   
(
  x 1 each). 
2.  Install the two support bracket covers [B] on the support brackets (
  x 1 each). 
Installation of the 500-Sheet Finisher 
 
1.  Unpack the finisher and remove all tapes and retainers. 
  
						

							 
B230/B237 1-40  SM 
2.  Attach the paper guide [A]. 
3.  Attach the unit holder [B] and the holder bracket [C] (knob screw x 4). 
 
ƒ  The holder bracket [C] must be placed outside the unit holder [B]. The holder 
bracket is provided with the bridge unit (B227). 
 
4.  Install the 500-sheet finisher [D] on the machine (
 x 1). 
 
5.  Attach the bracket cover [E]. 
6.  Install the output tray [F] on the 500-sheet finisher (2 snap rings). 
7.  Pull out the tray extension [G] of the bridge unit. 
8.  Turn on the main power switch, and then check the finisher operation.  
						

							  
SM 1-41 B230/B237 
Installation 
1.11  1000-SHEET FINISHER (B408) 
1.11.1 ACCESSORY CHECK 
Check the quantity and condition of the accessories against the following list. 
 
No. Description Q’ty B230/B237 
1  Front Joint Bracket  1  O 
2  Rear Joint Bracket  1  --- 
3  Rear Joint Bracket  1  O 
4 Grounding Plate  1  O 
5 Copy Tray  1  O 
6  Staple Position Decal  1  O 
7  Screw - M4 x 14  4  O 
8  Knob Screw - M4 x 10  1  O 
9  Screw - M3 x 8  1  O 
10  Knob Screw - M3 x 8  1  O 
O = Necessary, --- = Not necessary 
  
						

							 
B230/B237 1-42  SM 
1.11.2 INSTALLATION PROCEDURE 
 
ƒ Unplug the main machine power cord before starting the following 
procedure. 
 
If this finisher will be installed on the B230 or B237 copier, the following options must be 
installed before installing this finisher. 
- Bridge Unit (B227) 
- Paper Feed Unit (B800) or LCT (B801) 
1.  Unpack the finisher, and then remove the stopper [A] and tapes (
 x 1). 
 
2.  Install the front joint bracket [B], holder bracket [C] (
  x 2 - M4 x 14), and rear 
joint bracket [D] (
  x 2 - M4 x 14). 
 
ƒ  The holder bracket [C] must be placed outside the front joint bracket [B]. The 
holder bracket is provided with the bridge unit (B227).  
						

							  
SM 1-43 B230/B237 
Installation 
 
3.  Install the grounding plate [E] on the finisher (
  x 2 - M3 x 8). 
 
ƒ  Use the screw removed in step 1 and the screw from the accessory box. 
4.  Open the front door [F] of the finisher, and then pull the locking lever [G]. 
5.  Align the finisher on the joint brackets, and lock it in place by pushing the 
locking lever. 
6.  Secure the locking lever (1 knob screw - M3 x 8). 
7.  Close the front door. 
8.  Install the copy tray [H] (1 knob screw - M4 x 10). 
9.  Connect the finisher cable [I] to the main machine below the right rear handle. 
 
10.  Attach the staple position decal [J] to the ARDF as shown. 
11.  Turn on the main power switch and check the finisher operation.  
						

							 
B230/B237 1-44  SM 
1.12  1000-SHEET BOOKLET FINISHER (B793) 
1.12.1 ACCESSORY CHECK 
Check the quantity and condition of the accessories against the following list. 
No. Description Q’ty 
1  Rear Joint Bracket  1 
2  Front Joint Bracket  1 
3 Grounding Plate  1 
4 Upper Output Tray  1 
5 Cushion   2 
6 Lower Output Tray  1 
7  Short Knob Screw  1 
8  Long Knob Screw  1 
9  Screw (M3 x 8)  2 
10  Screw (M4 x 14)  4  
						

							  
SM 1-45 B230/B237 
Installation 
 
1.12.2 INSTALLATION PROCEDURE 
 
ƒ Unplug the main machine power cord before starting the following 
procedure. 
The bridge unit (B227) and optional paper feed unit (B800 or B801) must be installed 
before installing this finisher (B793). 
 
1.  Unpack the finisher and remove all tapes and packing materials from the 
finisher.  
						

							 
B230/B237 1-46  SM 
 
2.  Open the front door [A] of the 1000-sheet booklet finisher, and then pull out the 
jogger unit [B]. 
3.  Remove all tapes and packing materials from the inside of the finisher. 
 
4.  Attach the cushions [C] to the finisher.   
 
ƒ  Make sure that the cushions are placed within 0 to 1 mm [D] from the edge of 
the cover or frame. 
5.  Install the ground plate [E] on the finisher (
  x 2; M3 x 8).  
						

							  
SM 1-47 B230/B237 
Installation 
 
6.  Attach the rear joint bracket [F]   
(
x 2, M4 x 14). 
7.  Attach the front joint bracket [G] and the holder bracket [H] (
  x 2; M4 x 14). 
 
ƒ  The holder bracket [H] must be placed outside the front joint bracket [G]. The 
holder bracket is provided with the bridge unit (B227). 
 
8.  Pull the lock lever [I] (Long knob screw x 1). 
9.  Slowly push the finisher to the left side of the machine, keeping its front door 
open until the brackets [J] [K] go into their slots. 
10.  Push the lock lever [I], and then secure it (Long knob screw x 1).   
11.  Close the front door of the finisher. 
12.  Connect the finisher connector [L] to the machine.  
						

							 
B230/B237 1-48  SM 
 
13.  Install the upper output tray [M] (Short knob screw x 1). 
14.  Install the lower output tray [N]. 
15.  Turn on the main power switch of the machine. 
16.  Check the 1000-sheet booklet finisher operation.