Sharp Mx2310u User Guide

							2-102
COPIER
Contents
ADDING A WATERMARK TO A COPY (Watermark)
This function requires the hard disk drive.
When making a copy, specific text can be added to the copy as a watermark. The colour, density, angle, and pages (first 
page only or all pages) can be selected for a watermark. The watermark is printed at the centre of the paper.
Printing CONFIDENTIAL on the paper
The following 12 selections are available for the stamp text.
Three levels can be selected for the density of the watermark.
Seven colours can be selected for the watermark colour.
The angle of a watermark can be selected in the range +90 degrees to -90 degrees in increments of 45 degrees.
CONFIDENTIALPRIORITYPRELIMINARYFINAL
FOR YOUR INFO.DO NOT COPYIMPORTANTCOPY
URGENTDRAFTTOP SECRETPLEASE REPLY
1
Touch the [Watermark] key in the stamp selection screen.
See steps 1 to 4 of GENERAL PROCEDURE FOR USING STAMP (page 2-85).
2
Touch the key of the watermark that you 
wish to use.
CONFIDENTIAL
CancelOK
PRIORITYCONFIDENTIAL
DO NOT COPYFOR YOUR INFO.
DRAFTURGENT
FINALPRELIMINARY
COPYIMPORTANT
PLEASE REPLYTOP SECRET
Print Colour
All Pages
First Page
Angle
Stamp
Watermark
Bk213
45
(+90   -90) 
						

							2-103
COPIER
Contents
3
Touch the [Print Colour] key and set the 
colour and density.
Touch the colour that you wish to use.
If you wish to darken the selected colour, touch the   key. 
If you wish to lighten the selected colour, touch the   key.
When you have finished selecting the settings, touch the [OK] 
key.
 If you selected a colour other than [Bk (Black)], press the [COLOUR START] key. Pressing the [BLACK & WHITE 
START] key will print the stamp in black and white.
 If the stamp is printed in colour on a black and white copy, the copy will be included in the full colour count.
4
Touch the   keys to set the angle of 
the watermark.
5
Select the pages that the watermark will 
be printed on and touch the [OK] key.
Select printing on the first page only, or printing on all pages.
After touching the [OK] key, continue from step 5 of GENERAL 
PROCEDURE FOR USING STAMP (page 2-85) to complete 
the copy procedure.
The watermark text cannot be edited.
To cancel a watermark setting...
Touch the [Cancel] key in the screen of step 2.
CancelOK
PRIORITYCONFIDENTIAL
DO NOT COPYFOR YOUR INFO.
DRAFTURGENT
FINALPRELIMINARY
COPYIMPORTANT
PLEASE REPLYTOP SECRET
Print ColourBk213
All Pages
First Page
Stamp
Watermark
Angle
45
(+90   -90)
Stamp
Print ColourOK
B(Blue)G(Green)R(Red)
Bk(Black)
Y(Yellow)M(Magenta)C(Cyan)
Exposure
123
CancelOK
PRIORITYCONFIDENTIAL
DO NOT COPYFOR YOUR INFO.
DRAFTURGENT
FINALPRELIMINARY
COPYIMPORTANT
PLEASE REPLYTOP SECRET
Print Colour
All Pages
First Page
Angle
Stamp
Watermark
Bk213
45
(+90   -90)
CancelOK
PRIORITYCONFIDENTIAL
DO NOT COPYFOR YOUR INFO.
DRAFTURGENT
FINALPRELIMINARY
COPYIMPORTANT
PLEASE REPLYTOP SECRET
Print Colour
All Pages
First Page
Angle
Stamp
Watermark
Bk213
45
(+90   -90) 
						

							2-104
COPIER
Contents
[Image Edit] KEY
When the [Image Edit] key is touched in the 2nd special modes menu screen, the image edit menu screen opens.
Image edit menu screen
(1) [Photo Repeat] key
☞REPEATING PHOTOS ON A COPY (Photo Repeat) 
(page 2-105)
(2) [Multi-Page Enlargement] key
☞CREATING A LARGE POSTER (Multi-Page 
Enlargement) (page 2-107)
(3) [Mirror Image] key
☞REVERSING THE IMAGE (Mirror Image) (page 
2-110)(4) [A3 Full Bleed] key ([11x17 Full Bleed] key)
☞COPYING A3 (11 x 17) ORIGINALS WITH NO 
EDGE CUT-OFF (A3 (11 x 17) Full Bleed) (page 
2-111)
(5) [Centring] key
☞COPYING IN THE CENTRE OF THE PAPER 
(Centring) (page 2-113)
(6) [B/W Reverse] key
☞REVERSING WHITE AND BLACK IN A COPY (B/W 
Reverse) (page 2-115)
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
CentringA3
Full Bleed
Photo Repeat
OKSpecial Modes
Image Edit
Special Modes
22
OK
Image Edit
Proof Copy
Colour
Adjustments
Slow Scan
ModeOriginal 
CountMixed Size
Original
Stamp
Quick FileFile(1) (2) (3)
(4) (5) (6) 
						

							2-105
COPIER
Contents
REPEATING PHOTOS ON A COPY (Photo Repeat)
Photo Repeat is used to create repeated images of a photo-size original (130 mm x 90 mm size, 100 mm x 150 mm 
size, 70
 mm x 100 mm size, 65 mm x 70 mm size or 57 mm x 100 mm size (3 x 5 size, 5 x 7 size, 2-1/2 x 4 size, 
2-1/2
 x 2-1/2 size or 2-1/8 x 3-5/8 size)) on a single sheet of copy paper as shown below. Up to 24 images (when the 
image is 65
 mm x 70 mm size (2-1/2 x 2-1/2 size)) can be repeated on a single sheet of paper.
Original sizes up to 130 mm x 90 mm (3 x 5)
Original sizes up to 70 mm x 100 mm (2-1/2 x 4)
Original sizes up to 57 mm x 100 mm 
(2-1/8 x 3-5/8)Original sizes up to 100 mm x 150 mm (5 x 7)
Original sizes up to 65 mm x 70 mm 
(2-1/2 x 2-1/2)
Copying on A4 (8-1/2 x 11) 
size paper
4 copies are made.
Copying on A3 
(11 x 17) size paper
8 copies are made.
Copying on A4 (8-1/2 x 11) 
size paper
8 copies are made.
Copying on A3 
(11 x 17) size paper
16 copies are made.
Copying on A4 (8-1/2 x 11) 
size paper (Ratio 95%)
10 copies are made.
Copying on A4 (8-1/2 x 11) 
size paper
2 copies are made.
Copying on A3 
(11 x 17) size 
paper
4 copies are made.
Copying on A4 (8-1/2 x 11) 
size paper
12 copies are made.
Copying on A3 
(11 x 17) size paper
24 copies are made.
1
Place the original face down on the 
document glass.
 When placing a 130 mm x 90 mm, 100 mm x 150 mm, 
70 mm x 100 mm, 65 mm x 70 mm or 57 mm x 100 mm 
(3 x 5, 5 x 7, 2-1/2 x 4, 2-1/2 x 2-1/2 or 2-1/8 x 3-5/8) 
photo size original, place the original with the long side 
aligned against the left side of the document glass.
 When placing a business card size original, place the original 
with the long side aligned against the far side of the 
document glass. 
						

							2-106
COPIER
Contents
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
(4) Touch the [Photo Repeat] key.
☞[Image Edit] KEY (page 2-104)
3
Select Photo Repeat settings.
(1) Touch the key showing the original type 
and paper size combination that you want 
to use.
Touch the   keys to switch through the screens and 
touch the desired repeat type key (A4 or A3 (8-1/2 x 11 
or 11 x 17)).
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
When making repeat copies of a business card size original (up to 57 mm x 100 mm (2-1/8 x 3-5/8)), only A4 
(8-1/2 x 11) can be selected for the paper size.
4
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key. (For the second original and following originals, use the same [START] key as you did for the 
first original.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The original must be placed on the document glass.
 Only A4 (8-1/2 x 11) or A3 (11 x 17) size paper can be used.
 The copy ratio is 100% when this function is used. (The ratio cannot be changed.) However, for a business card size 
original (up to 57 mm x 100 mm (2-1/8 x 3-5/8)), the images are reduced to 95%.
To cancel the photo repeat setting...
Touch the [Cancel] key in the screen of step 3.
OK
OKCancel
Image Edit
Photo Repeat
Original SizeRepeat Type
A4/8½x11A3/11x17
48
15
   3x 5
  130x 90mm
(1)(2) 
						

							2-107
COPIER
Contents
CREATING A LARGE POSTER (Multi-Page 
Enlargement)
This function is used to enlarge an image of an original and print it as a composite image using multiple sheets of paper.
1
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
(4) Touch the [Multi-Page Enlargement] key.
☞[Image Edit] KEY (page 2-104)
Original 
(A4 (8-1/2 x 11) size)
Copy (enlarged image on 8 
sheets of A3 (11 x 17) paper) 
						

							2-108
COPIER
Contents
2
* The size that is twice A0 size.
Set the enlargement size and the original 
size.
(1) Select the size system that you wish to use 
for multi-page enlargement.
Touch the   keys to display the screen that shows 
the desired group of sizes.
 1st screen: A system
 2nd screen: B system
 3rd screen: Inch system
(2) Select the enlargement size.
(3) Select the size of the original to be used.
A suitable original placement orientation (A) and the 
number of sheets of paper required for the enlarged 
image (B) are displayed based on the selected original 
size and enlargement size.
Check the placement orientation and number of sheets.
The combinations of original sizes and enlargement sizes 
shown in the table at left are possible for multi-page 
enlargement.
 An A size original cannot be enlarged to a B size, and a B size original cannot be enlarged to an A size.
 To print a borderline around the copy image, touch the [Border Print] key so that it is highlighted.
3
Place the original face down on the 
document glass in the orientation 
indicated in the screen.
Ready to scan for copy. Copies will be
delivered in 2 parts.
OK
OKCancelBorder Print
Image Edit
Multi-Page Enlargement
A2
A4A1
A0
A0x2
A5
A3
Enlargement Size
(A Size)Original SizeOriginal Orientation13
(2)(A)(1)(3) (B)
A2                   A3, A4, A5
A1                   A3, A4, A5
A0                   A3, A4
A0 x 2*            A3
B3                   B4, B5
B2                   B4, B5
B1                   B4, B5
B0                   B4 
22 x 17       11 x 17, 8-1/2 x 14, 8-1/2 x 11
22 x 34       11 x 17, 8-1/2 x 14, 8-1/2 x 11
34 x 44       11 x 17, 8-1/2 x 14, 8-1/2 x 11
44 x 68       11 x 17
Enlargement size        Original size
Inch system
B system A system 
						

							2-109
COPIER
Contents
4
Touch the [OK] key.
You will return to the special modes screen. Touch the [OK] key 
to return to the base screen of copy mode.
5
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Copying will begin.
If you have selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and 
then touch the [Read-End] key. (For the second original and following originals, use the same [START] key as you did for the 
first original.
To cancel scanning and copying...
Press the [STOP] key ( ).
 The original must be placed on the document glass.
 Overlap of sections of image
- There will be a margin around the edges of each copy.
- Areas for overlapping the copies will be created at the leading and trailing edges of each copy.
 If an original size is selected first, a message will appear indicating the enlargement sizes that can be selected. If an 
enlargement size is selected first, a message will appear indicating the original sizes that can be selected.
 If a combination of settings is selected for which multi-page enlargement is not possible, invalid selection beeps will sound.
 The paper size, number of sheets required for the enlarged image, and the ratio are automatically selected based on the 
selected original size and enlargement size. 
(The paper size and ratio cannot be selected manually.)
 If no paper trays have the size of paper that was automatically selected, Load XXX paper will appear. Change the paper 
in one of the trays or the bypass tray to the indicated size of paper.
To cancel the multi-page enlargement setting...
Touch the [Cancel] key in the screen of step 2.
Although the multi-page enlargement setting is cancelled, the ratio selected automatically is kept valid.
To return the ratio to 100%...
To return the ratio setting to 100%, touch the [Copy Ratio] key to display the ratio menu and then touch the [100%] key.
Original Orientation
OK
OKCancelBorder Print
Image Edit
Multi-Page Enlargement
Original Size13A2
A4A1
A0
A0x2
A5
A3
Enlargement Size
(A Size) 
						

							2-110
COPIER
Contents
REVERSING THE IMAGE (Mirror Image)
This feature is used to make a copy that is a mirror image of the original.
1
Place the original.
Place the original face up in the document feeder tray, or face down on the document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
☞[Image Edit] KEY (page 2-104)
3
Select Mirror Image.
(1) Touch the [Mirror Image] key so that it is 
highlighted.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
4
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Copying will begin.
If you are using the document glass to copy multiple original pages, copying will take place as you scan each original. If you have 
selected sort mode, change originals and press the [START] key. Repeat until all pages have been scanned and then touch the 
[Read-End] key. (For the second original and following originals, use the same [START] key as you did for the first original.
To cancel scanning and copying...
Press the [STOP] key ( ).
To cancel a mirror image setting...
Touch the [Mirror Image] key in the screen of step 3 so that it is not highlighted.
Original Mirror image copy
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
CentringA3
Full Bleed
Photo Repeat
OKSpecial Modes
Image Edit
(1)(2) 
						

							2-111
COPIER
Contents
COPYING A3 (11 x 17) ORIGINALS WITH NO EDGE 
CUT-OFF (A3 (11 x 17) Full Bleed)
This feature lets you copy an entire A3 (11 x 17) size original at full size with no image cut-off at the edges.
A3W (12 x 18) size paper is used, which is slightly larger than A3 (11 x 17) size.
1
Place the original face down on the 
document glass.
2
Select the special modes.
(1) Touch the [Special Modes] key.
(2) Touch the   keys to switch through the screens.
(3) Touch the [Image Edit] key.
☞[Image Edit] KEY (page 2-104)
3
Select A3 (11x17) Full Bleed.
(1) Touch the [A3 Full Bleed] or [11x17 Full 
Bleed] key so that it is highlighted.
(2) Touch the [OK] key.
You will return to the special modes screen. Touch the 
[OK] key to return to the base screen of copy mode.
A3 (11 x 17) size originalA3 (12 x 18) full bleed copy
OK
Mirror
Image
B/W
Reverse
Multi-Page
Enlargement
CentringA3
Full Bleed
Photo Repeat
Special Modes
Image Edit
OK
(1)(2)