Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

							infinite TM Digital SystemsTF NO: 46a
Direct Inward Dialing (Con’t)
B. Direct Inward Dialing Parameters:
The buttons on the digital terminal are defined as shown below when entering the DID programming area:
1.Press FLASH and dial [45]. The following message is shown on the display phone:
DID
ENTER BUT-TON NUMBER
aTo program the number of DID digits:
1.Press the DIGITS Button (Button #l) in the flexible button field for programming the number of digits the system
will look at for routing purposes. The following message is shown on the display phone:
NUMBER OF DIGITS
2-73
2.Enter a one-digit entry (2-7) on the dial pad which corresponds to the number of digits used for the routing of
the DID number.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the number of DID digits is set to 3.
To program the type of DID Signaling:
1.Press the SIGNALING Button (Button #2) in the flexible button field for programming the type of DID signaling
*desired. The following message is shown on the display phone:
TYPE
0
2.Enter a one-digit entry (O-l) on the dial pad.
[0] 
= Wink
[l] = Delay
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the type of DID Signaling is set for wink.
Vodavi Communications SystemsPage 8 of 22TF NO. 46a
8300 E. 
Raintree DriveScottsdale, AZ 65260(602) 443-6000 
						

							infinite ‘” Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
To change the Wink Timer:
1.Press the WINK TIMER Button (Button #3) in the flexible button field for changing the Wink Timer settings. The
following message is shown on the display phone:
2.Enter a three-digit value on the dial pad which corresponds to 100-300 milliseconds.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
4Default: By default, the Wink Timer is set for 140 milli-seconds.To change the Delay Timer:
1.Press the DELAY TIMER Button (Button #4) in the flexible button field for changing the Delay Timer settings.
The following message is shown on the display phone:
2.Enter a three-digit value of the dial pad which corresponds to 000-200 milli-seconds.
3.Press the HOLD button to save the entry. Confirmation tone will be heard and the display will update.
Default: By default, the Delay Timer is set to 140 milliseconds.
Vodavi Communications SystemsPage 9 of 22TF NO. 46a
6300 E. Rainlree DriveScottsdale, AZ 65260
(602) 443-6000 
						

							infinite ly Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
C. Initialization of DID Tables:
Description:
This section describes the procedures and steps necessary to initialize the system database returning any
programmed data to its original or default value. The entire system database may be initialized or various portions
of the database may be individually initialized. In addition to initialization of the entire database, a system reset
(Button 
#20) command is also included in this section for clearing meantime errors without initializing the database.
The buttons on the digital terminal are defined as shown below when entering the Initializing 
DataBase Parameters
programming area:
Programming:
1.Press FLASH and dial [80]. The following message is shown on the display phone:
if the lCLlD/DID Table(s) need to be initialized:
2.Press the ICLID/DID TABLES Button (Button #9). The following message will be shown on the display phone:
w-j
3.To initialize the ICLID/DID Table(s), press the HOLD button, Confirmation tone will be heard.
Vodavi Communications SystemsPage 10 of 22TF NO. 46a
8300 E. 
Raintree DriveScottsdale, AZ 85260(602) 443-6000 
						

							infinite ly Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
If the DID Timers need to be initialized:
1.Press the DID-TIE TMRS Button (Button #14). The following message will be shown on the display phone:
INITIALIZE DID-TIE TMRS
PRESS HOLD
3.To initialize the DID Timers, press the HOLD button. Confirmation tone will be heard
Vodavi Communications SystemsPage 11 of 22TF NO. 46a
6300 E. 
Rainlree Drive
Scottsdale, AZ 65260(602) 443-6000 
						

							infinite rn Digital Systems
Direct Inward Dialing (Cont’d)
D. Printing of DID Tables:
Description:TF NO: 46a
This section describes the procedures and steps necessary to print Data Base Parameters and various portions
of the system.The buttons on the key telephone are defined as shown below when entering the Print Data Base Parameters
programming area.
With a printer connected to the RS-232C port on the DVX 
” CPB board, the currently stored customer database
can be printed or “uploaded” into a file. This command allows the entire database to be “dumped” as a permanent
record which can serve as a hard copy of the database .
The system Baud rate must match that of the printer or receiving device.
Default: None
Related Programming: Refer to Sec. 710.8, Baud Rate Assignments for setting the baud rate of the RS-232C port
on the Central Processor Board (CPB) on the DVX 
” system.
Vodavi Communications SystemsPage 12 of 22TF NO. 46a
6300 E. 
Raintree Drive
Scottsdale, AZ 65260(602) 443-6000 
						

							infinite ly Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
Programming:
1.Press FLASH and dial [85]. The following message is shown on the display phone:
If the 
ICLID/DID Table(s) need to be printed:
2.Press the ICLID-DID TABLES Button (Button #9). The following message will be shown on the display phone:
3.To print the ICLID/DID Table(s), press the HOLD button, The following message will be shown on the display
phone:The following is an example of the 
ICLID/DID Table(s) database printout.
PRINTING ICLID-DID
ICLID NAMEBAUD PORT
N
Y2400 1
ICLID TRANSLATION TABLE
ENTRY ROUTE NAME
300##
. . .. .
. . .. .
499##
ICLID UNANSWERED CALL TABLE
____----------___----------NONENUMBER
Vodavi Communications SystemsPage 13 of 22TF NO. 46a
8300 E. Rainlree DriveScottsdale, 
AZ 65260(602) 443-6000 
						

							TF NO: 46a
Direct Inward Dialing (Cont’d)
PRINTING ROUTEadm>ROUTE RING ASSIGNMENTS__----------
00NONE
99NONE
1001OOB. .199199BPRINTING DID TRANS NO
adm>DID TRANSLATION TABLE
ENTRY
000
001002
003
004
005
006
007
008
009
010. . .
. . .
095
096
097098
099
100-101
102
103104
105
. . .
99;996
997
998
999ROUTENUMBER
1000000000
1010000001
1020000002
1030000003
1040000004
1050000005
1060000006
1070000007
1080000008
1090000009
110
0000010
. . .
. . . . . . .
. . .. . . . .1950000095
1960000096
1970000097
1980000098
1990000099
1000000100
1010000101
10200001021030000103
1040000104
1050000105
. . .. . . . . . .
. . .. . . . . . .1950000995
1960000996
1970000997
1980000998
1990000999NAME
Page 14 of 22TF NO. 46a
Vodavi Communications Systems8300 E. Raintree Drive
Scottsdale, AZ 85260(602) 443-6000 
						

							infinite ‘” Digital SystemsTF NO: 46a
Direct Inward Dialing (Cont’d)
If a printout of the DID-TIE System Parameters is desired:
1.Press the DID-TIE TIMERS Button (Button #14). The following message will be shown on the display phone:
2. To print the DID-TIE System parameter database , press the HOLD button. The following message will be
shown on the display phone:
PRINT DID-TIE TMRS
4When the system has finished sending the information to the printer, confirmation tone will be heard.
The following is an example of the DID-TIE Timers database printout.
PRINT DID-TIE TMRS
PRESS HOLD
PRINTING DID-TIE TMRS
DID
---DIG SIG WNK DLY
3 0140 140
TIE
SIG WNK REL REZ GRD DLY
01402001502009Vodavi Communications SystemsPage 15 of 22TF NO. 46a
8300 E. 
Raintree DriveScottsdale, AZ 65260(602) 443-6000 
						

							infinite ‘” Digital Systems
DID Default Table Entries (Flash 44)TF NO: 46a
Vodavi Communications Systems
6300 E. 
Raintree DrivePage 16 of 22
Scottsdale, AZ 65260TF NO. 46a
(602) 443-6000 
						

							infinite ‘* Digital SystemsTF NO: 46a
57I001*I-II0000...-.57
-58001*0000-58
IO 59II-59 I001*I~---- ,
-600010000-60
-61001*0000-61
e-e-620010000-62
-630010000-63-64
001*0000~64
-65001*0000-65
-66001*0000-66-67
001*0000-67
II-68I001*I[ 0000-68 1Vodavi Communications SystemsPage 17 of 22TF NO. 46a
6300 E. 
Raintree Drive
Scottsdale, AZ 65260(602) 443-6000