Vodavi Infinite Dvx Iii Hybrid Key Telephone System Installation Manual

							INITIALIZE DATABASE PARAMETERSinfinite” DVX I’Digital Key Telephone System
INIT. DATABASE PARAMET
ERS (Cont’d)
M. Initialize VM Group Parameters
Programming Steps
If VM Group Parameters need to be initialized:1. Press the VM Group Parameters flexible
button (Button 
#13). The following mes-
sage will be shown on the display phone:Description
VM Group parameters maybe initialized setting
all data fields to their original, default values.2. To initialize the VM Group parameters,
press the HOLD button. Confirmation
tone will be heard.4PROGRAM CODE
~WITON~1  FLASH 651  FLEX 1
FEATUREDEFAULT VALUE-(after initializing)I 1-8 I
Vnire Mail CT-mlps 4&)-447No Voice Mail groups are
establishedI- -. ---- _._-L ULVCFLASH 66
9Alternate VM Group AssignNo Alternate VM groupassignment is made
10
Leave TableNo outpulsing table is
referenced
11
12l-7
Retrieve Table
VM Station Assignments
Voice Mail Out-Pulsing Tablesfor in-band signalingNo outpulsing table isreferenced
NO stations are assignedOut-pulse tables are empty
by default
FLASH 67
8
Voice Mail Disconnect Table
Disconnect table is empty
1In-Band Digits for Incoming
co CalIsDisabled by default
2
Voice Mail Transfer/ForwardDisabled by default
770-1s
Issue 1, February 1994 
						

							infinite” DVX I’Digital Key Telephone System
INITIALIZJ3 DATABASE PARAMETERS
INIT. DATABASE PARAMET
ERS (Cont’d)
N. System Reset
Programming StepsIf the system needs to be reset but not 
initial-
ized:1. Press the 
RESET flexible button (Button
#20). The following message will be shownon the display phone:
Description
This feature provides a hard system reset from
the 
keyset instead of the KSU. This is useful incases where miscellaneous data errors have
occurred and the system needs to be reset
without initializing the entire database.
2.To reset the system without initializing thedatabase, press the HOLD button. No
Confirmation tone will be heard and the
system will now reset.Issue 1, February 1994
770-19 
						

							infznitem DVX I’
Digital Key Telephone SystemSECTION 775
775.1TABLE OF CONTENTS FOR SECTION 775
PRINTING SYSTEM DATABASE PARAMETERS.........................775- 
1INTRODUCTION....................................................................................
775- 1A. Printing System Parameters......................................................
.775-2
B.Printing CO Line Attributes........................................................775-4
C.Printing Station Attributes.........................................................775-6D. Printing CO and Station Port Parameters..................................
.775-8E. Printing Exception Tables........................................................
775- 10F. Printing System Speed Bins.....................................................775-12
G. Printing LCR Tables.................................................................775-14
H. Printing Entire System Data Base............................................775-23
I.Printing ICLID Tables...............................................................775-24
J.Printing Directory Dialing Table Parameters.......i.....................775-27
K. Printing Hunt Group Parameters..............................................775-29
L.Printing ACD or UCD Group Parameters..................................775-3 1
M.Printing Voice Mail Group Parameters......................................775-33
N. Abort Printing..........................................................................775-35
Issue 1, February 1994775-i 
						

							infznite” DVX I’Digital Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERS
SECTION 775PRINTING SYSTEM DATABASE 
PARAJUETERS
775.1INTRODUCTION
Program.ming Steps
If the system is in the programming mode,
continue using the program codes. If starting toprogram here, enter the programming mode.
Refer to Sec. 700.2, Program Mode Entry (Key
Station).
If 
DataBase Parameters need to be printed:
1.Press FLASH and dial [85]. The following
will be shown on the display phone:
2.Choose the portion of the database to be
printed by pressing the appropriate but-
ton in the flexible button field.DescriptionThis section describes the procedures and
steps necessary to print Data Base Parameters
and various portions of the system.The buttons on the key telephone are defined
as shown below when entering the Print Data
Base Parameters programming area.
* Features available with optional software.With a printer connected to the 
RS232C port
(future) on the Central Processor Unit (CPU) orto either Port 
#3 or Port #4 on the I/O Expan-
sion Module, the currently stored customer
database can be printed or “uploaded” into a
file. This command allows the entire databaseto be “dumped” as a permanent record which
can serve as a hard copy of the database .The system Baud rate must match that of the
printer or receiving device.Refer to the following Figures for examples of
the database printouts. Also refer to the follow-
ing paragraphs for instructions on printing onlyportions of the database .
Default: NoneRelated Programming: Refer to Sec. 710.8,
Baud Rate Assignments, for setting the baud
rate of the RS-232C port (future) on Central
Processor Unit (CPU), Port 
#3 or Port #4 on the
I/O Expansion Module.
Issue 1, February 1994
775-l 
						

							System DataBase Printouts (Cont’d)
A Printing System Parameters
Programming StepsDescription
If a printout of all System Parameters is desired:
1.Press the SYSTEM PARAMETERS flexible
button (Button # 1). The following messagewill be shown on the display phone:With a printer connected to the RS-232C port
(future) on the Central Processor Unit (CPU) orto either Port 
#3 or Port #4 on the I/O Expan-
sion Module, the currently stored customer
database can be printed or “uploaded” into a
file. This command allows the System Parame-ters database to be “dumped” as a permanent
record which can serve as a hard copy.The system Baud rate must match that of the
printer or receiving device.
When printing the System Parameters the fol-
lowing data is printed;
l All System Timersal All System wide options (i.e. external
night ringing, Hold preference etc.. .)l Attendant programming
l Other system assignments (i.e.
Page/Relay Assignments, Execu-
tive/Secretary, SMDR etc. ..)l Weekly Night Mode schedule
Refer to the following Figure for an example of
the system parameters database printout.
Default: None
2.To print the system parameter database ,press the HOLD button. The following
message will be shown on the display
phone:
When the system has finished sending the in-
formation to the printer, confirmation tone will
be heard.System Timers:
SHR= System Hold Recall Timer
EHR= Exclusive Hold Recall Timer
ART= Attendant Recall Timer
XFR= Transfer Recall Timer
PFT= Preset Forward Timer
CFN= Call Forward No-Answer Timer
PT= Pause Timer
CPT= Call Park Timer
CFT= Conference Timer
PTO= Page Timeout Timer
COT= CO Ring Detect Timer
SRT= Single Line Receiver Timer
MWT= Message Wait Reminder Tone
IdIT= Hook Flash Timer
HFD= Hookswitch Bounce Timer
CQT= SMDR Call Qualification Timer
ACB= Auto Call Back Timer
RR= Reminder Ring Timer
RG= Release Guard TimerRelated 
Programmiug: Refer to Sec. 710.8,
Baud Rate Assignments, for setting the baud
rate of the RS-232C port on the Central Proces-sor Unit (CPU) (future) on Central Processor
Unit (CPU), Port 
#3 or Port #4 on the I/O
Expansion Module.
System Features:
AO=Attendant Override
SY= Hold PreferenceENR= External Night Ringing
EO=Exec Override Warn Tone
PW= Page Warning ToneBGM= Background Music
LCR= LCR Enable/Disable
AC=Forced Account Codes
GL=Group Listening
S=Idle Speaker Mode
CC= Call Cost Display FeatureMH= Music On Hold
V= Handset Receiver Gain
Q= Call Qualification Tone Option
775-2
Issue 1, February 1994 
						

							infkiteTM DVX I’Digital Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERS
SYSTEM PARAMETERS
Eng. Ver.
2.3D-0FFFSYSTEM TIMERS
-SHR EHR ART XFR PFT CFN PT
60180
14510152CPT CFT PTO COT SRT MWT HFT
1801015320010HFD CQT ACB RR RG
10 300 0 3
SYSTEM FEATURES
A0 SY ENR EO PW BGM LCR
N Y NYYY N
AC GL S CC 
MH V Q
N NN N YNN
BARGE IN WARN TONE ENABLED
SYSTEM LED FLASH RATES
INC CO RING30 IPM FLASH
INC ICM RING120 IPM FLUTTER
CALL FORWARD
30 IPM FLASH
MESSAGE WAITING15 IPM FLASH
ATTENDANT STATIONS
100 ### ###
DATE 
& TIME FORMATMM/DD/YY, 12 HOURS
PBX DIALING CODES
## ## ## ## ##
EXECUTIVE/SECRETARY PAIRINGS
l=######2=######3=######4=######RELAY ASSIGNMENTS
ON BOARD RELAY
1NONE2NONE3NONE
4NONE5NONE
6NONE7NONE
RELAY/SENSOR ###
1NONE2NONE
3NONE4NONE5NONE
6NONERELAY/SENSOR ###
1NONE2NONE3NONE
4NONE5NONE
6NONE
RELAY/SENSOR ###
1NONE2NONE
3NONE4NONE5NONE
6NONE
RELAY/SENSOR ###
1NONE2NONE3NONE
4NONEa5NONE
6NONE
I/O BAUD RATE
~-
Port1/On Board=2400Port2/Modem=1200Port3/RS232=2400
Port
4/RS422=2400
ACCESS CODE
1 DISA ACCESS
1002 ADMIN PASSWORD
3226
SDR TPE PNT BAUD PORT
NLD 802400 1
AUTO NIGHT MODEN
WEEKLY NIGHT MODE SCHEDULE
-ENDSTART
DAYTIMETIME
M 008001700
Tl08001700
w 208001700
T 308001700
F 408001700
s 5
########
S 6########
DIAL PULSE
RATIOSPEED
6040
1OPPSSYSTEM SLOT TYPE
ssssccccssss
Figure 775-l DB Printout of System Parameters
Issue 1, February 1994
775-3 
						

							PRINTING SYSTEM DATABASE PARAMETERSin$initem DVX I’Digital Key Telephone System
System 
DataBase Printouts (Cont’d)
B.Printing CO Line Attributes
Programming Steps
If a printout of the CO Line Attributes is desired:1. Press the CO LINE ATTRIBUTES flexible
button (Button #2). The following message
will be shown on the display phone:
2.To print the data for ALL CO Lines, press
the HOLD button. To print CO Line data
for a specified CO Line Range enter four
digits to specify the CO Line range (two
digits for the first line within the range and
two digits for the last line in the range i.e.
[0115]). If a printout of only one line is
desired enter that line twice (i.e. [OlOl]).Then press the HOLD button.
3. The following message will be shown on
the display phone and the CO Line data
will be printed:
When the system has finished sending the re-quested information to the printer, confirma-
tion tone will be heard.DescriptionWith a printer connected to the RS-232C port
(future) on the Central Processor Unit (CPU) orto either Port 
#3 or Port #4 on the I/O Expan-
sion Module, the currently stored customer
database can be printed or “uploaded” into a
file. This command allows either a range of COLines or the entire CO Line database to be
“dumped” as a permanent record which can
serve as a hard copy of the CO Line attribute
database .The system Baud rate must match that of the
printer or receiving device.When printing the CO 
Lint attributes the fol-
lowing data is printed:l All CO Line parameters within the
specified range.
0CO Line ringing assignments within the
specified range.l Dial Pulse Ratio and Speed settings
Refer to the following Figure for an example of
the CO Line attribute database printout.
Default: NoneRelated Programming: Refer to Sec. 710.8,
Baud Rate Assignments, for setting the baud
rate of the RS-232C port on the Central Proces-sor Unit (CPU) (future) on Central Processor
Unit (CPU), Port 
#3 or Port #4 on the I/O
Expansion Module.
Definition of Terms for CO Lines Printout
SIGNAL= DTMF/Dial Pulse
?YPE= CO/PBX
UNA= Universal Night Answer
PRI= CO Line Privacy
SUPV= Loop Supervision
DISA= Direct Inward System Access
FLTM= Flash TimerGRP= CO Line Group
COS= CO Line Class of Service
DIR= Trunk Direction
RD= Ring Delay Timer775-4Issue 1, February 1994 
						

							infinitem DVX I’
Digital Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERS
CO LINE ATTRIBUTES
co 01
LINE 01
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 1 2 00
RING ASSIGNMENTS
100Bco 02
LINE 02
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 1 2 00
RING ASSIGNMENTS
100Bco 03co 05
--
LINE 05
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 12 00
RING ASSIGNMENTS
100BCO 06
LINE 06
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP 
C& DIR RD
NN10 1 12 00
RING ASSIGNMENTS
100Bco 07
LINE 07
LINE 03
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 1 2 00
RING ASSIGNMENTS
10OBco 04
LINE 04
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 12 00
RING ASSIGNMENTS
100BSIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN10 1 12 00
RING ASSIGNMENTS
100BCO 08
--
LINE 08
SIGNAL TYPE UNA CONF PRI
DTMF CO YY Y
SUPV DISA FLTM GRP COS DIR RD
NN
10 1 12 00
RING ASSIGNMENTS
100B
. . .and so on thru CO Lines 48
Figure 775-2 DB Printout of CO Line Attributes
Issue 1, February 1994775-5 
						

							PRINTING SYSTEM DATABASE PARAMETERSinfinitem DVX I’Digital Key Telephone System
System 
DataBase Printouts (Cont’d)
C. Printing Station Attributes
Programming Steps
If a printout of the Station Attributes is desired:1. Press the 
STATION ATTRIBUTES flexible
button (Button #3). The following messagewill be shown on the display phone:
jPRINT STATIONS
2. To print data for all stations, press the
HOLD button. To print Station data for a
specified Station Range enter six digits to
specify the Station range (three digits for
the first station within the range and three
digits for the last station in the range i.e.
[ 1001091). If a printout of only one stationis desired enter that station twice (i.e.
[lo1 1011). Then press the HOLD button.3. The following message will be shown on
the display phone and the requested infor-
mation will be printed:
,,,,,,,,,,,,,,
When the system has finished sending the re-quested information to the printer, confirma-
tion tone will be heard.
PaPe “A” Features:
PAGE= Paging Access
DND= Do Not Disturb
CONF= Conference
EOR=Executive Override
PRI= Privacy
SPD= System Speed Dial Access
QUE= Line Queue Access
PLA= Preferred Line AnswerOHVO=Off-Hook Voice Over
FWD= Station Call Forward Access
LCR= LCR Class of ServiceSUB= ACD Supervisor Monitor Barge-m
REM= CO Line Ringing Options
DescriptionWith a printer connected to the RS-232C port
(future) on the Central Processor Unit (CPU) orto either Port 
#3 or Port #4 on the I/O Expan-
sion Module, the currently stored customer
database can be printed or “uploaded” into a
file. This command allows either a range of
station data or all stations data information to
be “dumped” as a permanent record which canserve as a hard copy of the station attribute
database .The system Baud rate must match that of the
printer or receiving device.
When printing the Station attributes the follow-
ing data is printed;l All current station parameters
Refer to the following Figure for an example of
a Station attribute database printout.
Default: NoneRelated Programming: Refer to Sec. 710.8,
Baud Rate Assignments, for setting the baud
rate of the RS-232C port on the Central Proces-sor Unit (CPU) (future) on Central Processor
Unit (CPU), Port 
#3 or Port #4 on the I/O
Expansion Module.
Pee “B” Features:
SID= Station IDAID= Associated ID 
(DSS/DIS Console)
DCOS= Day Class of Service
NCOS= Night Class of ServiceSPK= Speakerphone Option
PICKUP= Pickup Groups
PAGE= Paging Groups
PREFWD= Preset Forward Assignment
LCOS=LCR Class of ServiceBUTTONS= Refer to Table 730-2 Flexible
Button Display Designations, Page 
730-24.775-6
Issue 1, February 1994 
						

							in$initew DVX I’
Digitd Key Telephone System
PRINTING SYSTEM DATABASE PARAMETERS
STATION ATTRIBUTES
STA 102
STA 100
PAGE DND CONF EOR PRI SPD QUEY Y YN/A Y Y Y
PLA OHVO FWD LCR SUB REM
NN Y N N N
SID AID DCOS NCOS SPK
0110PICKUP PAGE PREFWD LCOS
110
CO ACCESS 1
BUTTONS
OlDlOO 02D101 03D102
04D103 05D104 06D10507D106 08D107 09DlO8lODlO9 llDll0 12Dlll
13COOl 14COO2 15COO316COO4 17COO5 18COO6
19LP2OPLl21CBK
22FWD23DND 24CNF
PRIME KEY 0 Y
STA 101
PAGE DND CONF EOR PRI SPD QUEY Y YN/A Y Y Y
PLA OHVO FWD LCR SUB REM
NN Y N N N
SID AID DCOS NCOS SPK
0110PICKUP PAGE PREFWD LCOS110
CO ACCESS 1
BUTTONS
OlDlOO 02D101 03D102
04D103 05D104 06D10507D106 08D107 09D108
lOD109 llCOO1 12CO0213coo3 14coo4-15coo516COO6 17coo7 18COO8
19LP2OPLl21CPO22LQU23CBK 24PKU
25MSG 26FWD 27DND
28CNFPRIME KEY 0 Y
PAGE DND CONF EOR PRI SPD QUEY Y YN/A Y Y Y
PLA OHVO FWD LCR SUB REM
NN Y N N N
SID AID DCOS NCOS SPK0110
PICKUP PAGE PREFWD LCOS110
CO ACCESS 1
BUTTONS
OlDlOO 02DlOl 03D10204D103 05D104 06D105
07D106 08D107 09D108lOD109 11COOl 12COO2
13coo3 14coo4 15coo516COO6 17coo7 18COO819LP2OPLl21CPO I
22LQU 23CBK 24PKU
25MSG 
26FWD27DND
28CNFPRIME KEY 0 Y
STA 103
PAGE DND CONF EOR PRI SPD QUEY Y YN/A Y Y Y
PLA OHVO FWD LCR SUB REMN
N Y N N N
SID AID DCOS NCOS SPK0110
PICKUP PAGE PREFWD LCOS110
CO ACCESS 1
BUTTONS
OlDlOO 02D101 03D10204D103 05D104 06D10507D106 08D107 09D108
lOD109 11COOl 12COO213coo3 14coo4 15coo5
16COO6 17coo7 18COO819LP2OPLl21CPO
22LQU23CBK 24PKU
25MSG 
26FWD27DND
28CNFPRIME KEY 0 Y
and so on thru stations 195Figure 
775-3 DB Printout of Station Attributes
Issue 1, February 1994775-7