GE Logiq P5 User Manual

							System Presets
LOGIQ 5 Basic User Manual 16-11
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
3.  Press Add. The Add Input Locale menu appears. On the 
pull-down menu, move the Trackball until you see Russian 
or Greek. Press Set to select. Press Ok. You are returned to 
the Input Locales menu.
 Figure 16-5. Adding Russian Input Locale 
						

							Customizing Your System
16-12 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
4.  Specify Russian or Greek as the default language by 
pressing Set as Default. 
 Figure 16-6. Set Russian to be the Default 
						

							System Presets
LOGIQ 5 Basic User Manual 16-13
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
5.  At the bottom of the Input Locales menu, you now need to 
specify the keys you will press to toggle between the 
English and the Russian or Greek keyboards. Press 
Change Key Sequence. The Change Key Sequence pop-up 
menu appears. Make sure the Enable Key Sequence box 
has a check mark in it. Select CTRL + SHIFT and say OK. 
You are returned to the Input Locales menu. 
 Figure 16-7. Set Keyboard Toggle Keystroke
6.  Apply the changes by pressing Apply. Press OK. 
						

							Customizing Your System
16-14 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
7.  Press the General tab. Set Your Locale (location) to Russian 
or Greek. 
 Figure 16-8. Set the Locale 
						

							System Presets
LOGIQ 5 Basic User Manual 16-15
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
8.  Press Set default at the bottom of the menu to Select 
System Locale. Press Ok. Then Apply the changes. 
 Figure 16-9. Selecting the System Locale
9.  A general system pop-up message appears. Answer Yes. 
 Figure 16-10. General Windows Pop-Up Message 
						

							Customizing Your System
16-16 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
10.  Restart the system when prompted: The system screens, 
menus, and Touch Panel display is now in Russian or 
Greek. 
 Figure 16-11. Restart System Prompt
To set up Russian (or Greek), follow the procedure below EACH 
TIME software is reloaded on your system. 
NOTE:   To have the settings take effect, you MUST turn off the system 
and turn it back on. 
To toggle between the Russian and English keyboards, press 
the CTRL + SHIFT keys at the same time.  
						

							System Presets
LOGIQ 5 Basic User Manual 16-17
Direction 2300002-100 Rev. 2
Keyboard Setup Procedure for Russian and Greek (continued)
Here is an example of the Russian keyboard: 
 Figure 16-12. Russian Keyboard
Here is an example of the Greek keyboard: 
 Figure 16-13. Greek Keyboard 
						

							Customizing Your System
16-18 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
System/System Imaging Preset Menu
The System/System Imaging screen allows you to specify 
parameters for cine loop storage and display, patient 
information, key usage, and image control and display.
 Figure 16-14. System/System Imaging Preset Menu 
Table 16-6: Cine Loop Store
Preset ParameterDescription
Time span (no ECG) 
[s]Select the number of seconds of CINE Loop 
storage (no ECG). The default is 3 seconds 
(approximately 77 B/W frames, 97 Color Frames). 
Preview loop before 
storeWhen selected, allows you to review cine loops 
before storage. 
						

							System Presets
LOGIQ 5 Basic User Manual 16-19
Direction 2300002-100 Rev. 2
System/System Imaging Preset Menu (continued)
Table 16-7: Cardiac
Preset ParameterDescription
Time before heart 
cycle [ms]Sets the total storage time span of the cine loop in 
ECG mode.
Time after heart cycle 
[ms]Sets the total storage time span of the cine loop in 
ECG mode.
Time span of systole 
[ms]The default systolic time to enable synchronization 
of cine loops.
Table 16-8: Biopsy Guides
Preset ParameterDescription
Show Center Line Displays center biopsy guideline. 
Show Outer Lines Displays outer biopsy guidelines. 
Enable 0.5cm 
markersActivates biopsy depth markers every 0.5cm. 
Table 16-9: Image Control and Display
Preset ParameterDescription
Horizontal Scale Select to display width markers. 
TGC Display Select to display TGC curve.
PW Velocity Units in 
cm/sSelect to change scale on timeline from centimeters 
per second to meters per second.
Split screen full 
height display of 
linear imagesWhen selected, while in split screen and using a 
linear probe, the system clips the sides of images 
so that the image can fill the available display.
Auto Invert on Linear 
SteerWhen selected, for auto calcs, automatically inverts 
the timeline if needed when using ASO.
Auto Invert on ASO Automatically inverts the spectrum with ASO. 
Audio Volume Adjusts the Doppler audio volume. 
Auto Freeze (15 
minutes)Automatically freezes the system after 15 minutes 
of inactivity.
Image Parameter 
Size (reboot required)Choices=small, medium, and large. Must reboot the 
system.
Show Clipboard Select to show clipboard. 
						

							Customizing Your System
16-20 LOGIQ 5 Basic User Manual
Direction 2300002-100 Rev. 2
System/System Measure Preset Menu
The System/System Measure screen allows you to specify 
measurement parameters such as the type of default OB 
measurements and calculations. You can also define cursor and 
Results Window default functionality.
 Figure 16-15. System/System Measure Preset Menu