Land Rover Range Rover 2002my On Workshop Procedures Lm 6th Edition Nas Rover Manual

							EXTERIOR FITTINGS
76-2-16 REPAIRS
Finisher - E post 
$% 76.43.36
Remove
1.Remove 4 studs securing finisher to E post.
2.Release 4 clips and remove finisher.
3.Remove and discard fixings from finisher.
4.Remove and discard fixing retaining sacks from 
E post.
Refit
1.Fit new fixing retaining sacks to E post.
2.Fit new fixings to finisher.
3.Fit finisher, secure with clips and studs.
Side finisher - windscreen 
$% 76.43.39
Remove
1.Remove 4 scrivets securing finisher to A post.
2.Release 4 fixings and remove finisher.
3.Remove and discard fixings from finisher.
4.Remove and discard fixing retaining sacks from 
A post.
Refit
1.Fit new fixing retaining sacks to A post.
2.Fit new fixings to finisher.
3.Fit finisher and secure fixings.
4.Fit and secure scrivets. 
						

							EXTERIOR FITTINGS
REPAIRS 76-2-17
Lower finisher - windscreen 
$% 76.43.41
Remove
1.Remove RH windscreen side finisher.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Side finisher - windscreen.
2.Remove both wiper arms.
 
 +  WIPERS AND WASHERS, REPAIRS, 
Arm - wiper - front screen.
3.Using LRT-99-500A remove aluminium boss 
from both wiper spindles and discard.
4.Remove plastic inserts from both wiper 
spindles.
5.Release both drain tubes from underside of 
finisher.
6.Release clips and carefully position finisher 
away from wiper spindles.
7.Slide lower windscreen finisher away from LH 
side finisher and remove.Refit
1.Position lower finisher beneath LH side finisher 
and secure with clips.
2.Fit both drain tubes to finisher.
3.Position plastic inserts to wiper spindles.
4.Fit new aluminium boss to both wiper spindles.
5.Fit wiper arms.
 
 +  WIPERS AND WASHERS, REPAIRS, 
Arm - wiper - front screen.
6.Fit RH windscreen side finisher.
 
 +  EXTERIOR FITTINGS, REPAIRS, 
Side finisher - windscreen.
M76 4362
LRT-99-500A 
						

							EXTERIOR FITTINGS
76-2-18 REPAIRS
Roof moulding
$% 76.43.68
Remove
1.Carefully raise the front edge of moulding, 
release from 11 clips and remove moulding.
2.Remove 11 clips from roof panel.
Refit
1.Clean roof channel.
2.Fit clips to roof panel.
3.Fit moulding and secure to clips.
Finisher - tailgate - lower 
$% 76.43.99
Remove
1.Carefully release 7 clips securing tailgate 
finisher to body. Remove finisher.
CAUTION: Always protect paintwork and 
glass when removing trim finishers.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
2.Remove 7 clips from tailgate finisher.
3.Noting fitted position remove and discard 4 
adhesive backed clips from finisher.
M76 4315 
						

							EXTERIOR FITTINGS
REPAIRS 76-2-19
Refit
1.Fit adhesive clips to finisher, note fitted 
position.
2.Fit retaining clips to finisher.
3.Clean tailgate, remove remaining adhesive 
residue.
4.Remove protective covering from adhesive 
pads, align finisher to tailgate and secure clips. 
Ensure adhesive pads are pressed into 
position.
Front grille 
$% 76.55.03
Remove
1.Remove 3 screws securing grille to bonnet 
locking platform.
2.Release 3 clips securing grille to armature.
3.Disconnect multiplug from ambient air 
temperature (AAT) sensor.
4.Remove grille.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
5.Release and remove AAT sensor from grille.
Refit
1.Fit AAT sensor to grille.
2.Connect multiplug.
3.Fit grille and secure with screws. 
						

							EXTERIOR FITTINGS
76-2-20 REPAIRS 
						

							INTERIOR FITTINGS
REPAIRS 76-3-1
INT ERIOR FITTINGS REPAIRS
Sun visor 
$% 76.10.47
Remove
1.Release sun visor from retaining clip.
2.Carefully release and remove trim from 
mounting.
3.Remove 3 Torx screws securing visor.
4.Disconnect multiplug and remove visor.
5.Remove screw securing sun visor clip to roof 
and remove clip.
Refit
1.Fit sun visor clip and secure with screw.
2.Position sun visor and connect multiplug.
3.Fit sun visor to roof and secure with screws.
4.Fit sun visor to clip.
5.Fit trim to mounting.
Mirror - interior 
$% 76.10.51
Remove
1.Release and remove mirror finishers.
2.Rotate mirror stem at its base to release from 
windscreen.
3. Models fitted with rain sensor: Disconnect 
multiplug from rain sensor.
4.Disconnect multiplug from mirror and remove 
the mirror.
Refit
1.Position mirror and connect multiplug.
2. Models fitted with rain sensor: Connect 
multiplug to rain sensor.
3.Fit mirror to location and rotate to secure.
4.Fit and secure mirror finishers.
M76 4527

     
						

							INTERIOR FITTINGS
76-3-2 REPAIRS
Trim casing - rear quarter - lower 
$% 76.13.12
Remove
1.Release D post upper finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - upper.
2.Remove D post lower trim.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - lower.
3.Remove Allen screw securing load space 
securing ring to load space floor, release and 
remove securing ring assembly.
4.Release and remove seat anchor escutcheon
5.Remove access panel.
6.Release 2 turn buckles.
7.Remove 3 scrivets and release trim casing.8.Disconnect multiplugs from interior light and 
accessory power socket.
9.Remove quarter trim.
Refit
1.Position trim casing and connect multiplugs.
2.Fit scrivets and turn buckles to secure trim.
3.Fit access panel.
4.Fit seat anchor escutcheon.
5.Position luggage space securing ring to body, 
locate peg. Fit and tighten bolt to 25 Nm (18 
lbf.ft). 
6.Fit D post lower trim.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - lower.
7.Fit D post upper finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - upper.
M76 4530 
						

							INTERIOR FITTINGS
REPAIRS 76-3-3
Foot rest finisher - LHD 
$% 76.13.24
Remove
1.Remove carpet retainer.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Retainer - front carpet.
2.Release 4 clips securing inner edge of footrest 
pad to finisher, roll pad clockwise and remove.
3.Remove bolt securing footrest finisher to body.
4.Lift bonnet lock release handle and withdraw 
finisher from clips. Pull horizontal and rearward 
to remove.
Refit
1.Fit finisher to A post and secure with clips.
2.Fit bolt securing footrest finisher to body and 
tighten to 3 Nm (2.2 lbf.ft).
3.Fit footrest pad and secure clips.
4.Fit carpet retainer.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Retainer - front carpet.
Trim finisher - A post - upper  
$% 76.13.26 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS) 
Precautions.
2.Release door aperture seal.
3.Remove cover from screw.
4.Remove Torx screw securing A post trim.
5.Release 3 clips securing A post trim and 
remove trim.
CAUTION: The airbag is mounted directly 
under this finisher, extreme care is 
necessary.
6.Remove retaining clips from trim.
Refit
1.Fit retaining clips to trim.
2.Fit A post trim and tighten screw to 2 Nm (1.5 
lbf.ft).
3.Fit screw cover.
4.Fit seal to door aperture.
5.Connect battery leads, earth lead last. 
						

							INTERIOR FITTINGS
76-3-4 REPAIRS
Trim finisher - A post - lower 
$% 76.13.27
Remove
1.Remove carpet retainer.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Retainer - front carpet.
2.Release sufficient door aperture seal to access 
lower trim finisher.
3.Release and remove finisher horizontally from 
2 retaining clips.
NOTE: Do not carry out further dismantling if 
component is removed for access only.
4.Check condition of finisher retaining clips in 
body, replace if damaged.
Refit
1.Fit retaining clips to body.
2.Fit and secure finisher.
3.Secure door aperture seal.
4.Fit carpet retainer.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Retainer - front carpet.
Trim finisher - B post - upper  
$% 76.13.28 
Before disconnecting the battery, ensure all text and 
cautions in the battery disconnection section are 
observed. 
 
 +  GENERAL INFORMATION, Electrical 
Precautions.
Remove
1.Make the SRS system safe. 
 
 +  GENERAL INFORMATION, 
Supplementary Restraint System (SRS) 
Precautions.
2.Remove front seat.
 
 +  SEATS, REPAIRS, Front seat.
3.Release door aperture seal from B and C 
posts.
4.Release 4 fixings securing B post lower 
finisher.
5.Release B post upper finisher from fixings and 
remove finisher assembly.
6.Remove and discard fixings from finisher.
7.Depress clips and remove B post upper 
finisher from lower finisher.
Refit
1.Fit upper B post finisher to lower finisher.
2.Fit new fixings to finisher.
3.Fit finisher assembly to upper fixings, position 
seat belt and secure lower finisher to B post.
4.Fit door aperture seals.
5.Fit front seat.
 
 +  SEATS, REPAIRS, Front seat.
6.Connect battery leads, earth lead last. 
						

							INTERIOR FITTINGS
REPAIRS 76-3-5
Trim finisher - D post - upper  
$% 76.13.30
Remove
1.Remove lower D post finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - lower.
2.Remove and discard Torx bolt from lower seat 
belt anchor.
3.Release upper D post finisher from seat belt 
webbing and remove finisher.
Refit
1.Pass seat belt through upper D post finisher, fit 
belt and tighten Torx bolt to 50 Nm (37 lbf.ft).
2.Fit finisher.
 
 +  INTERIOR FITTINGS, REPAIRS, 
Trim finisher - D post - lower.
Trim finisher - D post - lower  
$% 76.13.31
Remove
1.Remove parcel tray.
2.Release rear seat squab and fold seat forward.
3.Remove sufficient D post door aperture seal to 
access upper trim finisher.
4.Release D post upper finisher from upper 
clips.
5.Remove 2 Torx screws securing top edge of 
lower trim finisher. Release pegs at lower edge 
and remove.
Refit
1.Fit lower trim finisher and secure with Torx 
screws.
2.Fit D post upper finisher.
3.Check operation of rear seatbelt.
4.Secure seal to door aperture.
5.Position seat in upright position.
6.Fit parcel tray.