Vodavi Infinite Dvx I, Dvx Ii Hybrid Key Telephone Systems Installation Manual

							10 DATABASE PARMBEIERS itIfinike 
DVX1andDVXn 
Dfgital Key Tckphone Systems 
INIT. DATABASE P ARABEZEFU (Cont’d) 
B. InitiaIizc co Line Attrihutcs 
Pro- steps 
If CO Line Attributes need to be initialized: 
1. Press the CO Line Attributes flexible but- 
ton (Button #2). The followingmessagewill 
be shown on the display phone: 
IllrruLm Ii0 MS f 
PEEa tm 
Description 
The 
CO Lhe parameters may be initialized set- 
ting all data fields to their original, default 
values. The followlng data fields are returned to 
their default value upon initializing the CO Line 
parameters. 
2.To initialize the CO Line Attributes, press 
the HOLD button. Confirmation 
tone will 
be 
heard. 
PROGRAM CODE - 
FEATURE DEFAULT VALUE 
BU’ITON 
(after initializin@ 
FLASH 40 1 DlMF/PulseS@nalin~ ALL Lines set for DT?MF 
2 
CO/PF3X Marking ALL Lhes set for CO 
3 UnWersal Ni&t Answer 
Enabled on alI Lines 
4 DK% TFX-to-m (ConfJ 
Enabled on a.U Lines 
5 
Automatic Privaq Enabled on all Lines 
6 hop Supervision 
NO (disabled on all lines) 
I  
						

							iqfkite DV2I I md DVX ’ 
Dilofti Eey Telephone Systems - DATABASE PARAMETERS 
INIT. DATAEASE 
Pv RS (Co&d) 
c. Iui- Station Attributes 
Pro@rnming Steps 
If Station Attributes need to be initialized: 
1. Press the Station Attributes flexible button 
(Button #3). The following message will be 
shown on the display phone: Description 
The Station parameters may be initialized set- 
ting all data fields to their origiial. default 
values. The following data fields are returned to 
their default value upon initializing the Station 
2.To initialize the Station Attributes, press 
the HOLD button. Confiition tone will 
be heard. 
I 
i FLASH 50. Page “B” BUTTON 
A/l Page Access 
A/Z , Do Not Disturb 
A/3 ! Conference 
A/4 Executive Override 
A/5 privacy Release 
A/6 
System Speed Dial 
A/? Line Queuing 
A/8 Preferred Line Answer 
A/9 Off-Hook Voice-Over 
A/10 Call Forwaxd 
A/11 Forced LCR 
Station ID 
B/l DEFAULTVALUE 
I [after 3nitializIn~ 
Allowed (enabled) 
Allowed (enabled) 
Allowed [enabled) 
D&-allowed (disabled) 
Dis-allowed (disabled) 
Allowed (enabled) 
Ahowed (enabled) 
I&-allowed (disabled) 
i 
Disallowed (disabled) 
Allowed (enabled) 
Not Required (disabled) 
AU Key Stations default to 
Station 
ID 0 (keyset) 
Au Single Line Telephones 
and OPXs default to ID 5 
B/2 1 Station Class of Service 
B/3 Speakerphone Option 
D/4 pick-up Group(s) 
B/5 Paging Zone(s) 
B/6 
Preset Forward Desttnation 
B/7 CO Line Group Access 
B/8 LCR Class of Service 
Off-Hook Preference 
B/9 
B/10 
Flex Button Assignment (SLT w/o MSG Wait) 
All Stations assfgned COS 1 
1 Au Stations assQned option 1 
AU Stations assigned into 
Group I 
Au Stations assigned into 
Zone 1 
None assigned 
All Stations assigned access to 
Group 1 
All Stations @ven an LCR COS 
of0 
Is allowed to all stations with 
the ability to change the 
ZiSS&IYIRCXlt 
! See default button assignment 
ISSUC 1, January 1B- 
770-5  
						

							@finite DVX I and DVX I1 
Figure 770-l %-Button Default Button Mapping 
770-6 
hnc1,Jantuuy1993  
						

							iq#intie DVX’andDVX’ 
Dlgftal Key Telephone Systems 
u- 
FQum 770-2 S-Button Default Button Mapping 
Issue 1. Januaxy 1993 
770-7  
						

							w DATAEASE P-RS 
INIT. DATABASE PARAlldETE 
F& (Cont’d] 
D. Idtidize Station a.xLd co Port 
~CiCl-S 
h@Umdng steps 
If Group Parameters need to be initialized: 
1. Press the Staff on/CO Port Parameters flex- 
fble button lsutton #a)-). The following mes- 
sage will be shown on the display phone: 
i@inite DV2C’andDVX’ 
Di@a3 Xcy Telephone Systems 
Description 
Station and CO Port parameters may be initial- 
ized setting all stations and all CO Lines back 
to their original, default 
values. The folIowing 
data fields are returned to their default values 
2.To tnftialize the Station/CO Port parame- 
ters, press the HOLD button. Clmikmation 
tonewillbeheard. 
770-a 
bsue 
1, Jammy L-3  
						

							i@ite DVX’adDVX’ 
D&$td Key Telephone Systems - DATABASE PARAMETERS 
MIT. DATABASE PARAHEWE Fe3 (Cont’d) 
E. fnltiake Exception Tables 
Proggammhg Steps 
If Exception Tables need to be initialized: 
1. Press the Exception Tables flexible button 
(3utton #5). The following message will be 
shown on the display phone: 
i lrrrrmmnrMlEs 
; lJ3immlm Description 
The Exception Table parameters including the 
AIlow/Deny Tables and the Special Tables may 
be initialtzed setting all tables to their original. 
default values. The fokwing Tables are cleared 
returning to their default value upon initializing 
the Exception Tables pammeters: 
2. To initiake the Exception Tables. press the 
HOLD button. Confirmation tone will be 
heard. 
TABLE DEFAULTVALUE 
(after ini- 
ALLOWTABLE-A Table Cleared (no entries 
DENY TABLE - A Table Cleared (no enties) 
ALLOWTABLE-B 
Table Cleared (no entries) 
DENYTiU3LE-B 
Table Cleared (no entries) 
SPECIAL TABLE 
Table Cleared (no entries allowed, 
1 
I no area code specified) 
SPECIAL TABLE 
Table Cleared (no entries aIlowed. 
2 
no area code speclfiedl 
SPECIAL, TABLE 
Table Cleared [no entries aIlowed, 
3 
1 SPECIAL TABLE no area code specified) 
4 
Table Cleared (no entries allowed) 
tImme area code). 
Issue 1, January mQs 
770-9  
						

							m DATABASE PARAMETERS iq#inike DvX’andDVX’ 
Digital Key Telephone Systems 
INIT. DATABASE P ARAMETERS (Cont’d) 
F. l.&i&zt System Spttd Numbers 
Pragramming Steps 
If System Speed bins need to be initialized: 
l.FYtss the System Speed flexiile button 
(Button #6). The following message will be 
shown on the display phone: Description 
Numbers entered into the System Speed dial 
Table may be initialized clearing all bins to their 
orig-inal, default value [empty). All bins 20 
through 99 are cleared returning to their de- 
fault value (empty) upon initializing the Speed 
Dial Table. 
2.To initialize the.System Speed bins, press 
the HOLD button. Confirmation tone will 
be heard.  
						

							@jWte DK&ndDVXn 
Mgltal Ecy Telephone Systcme B DATABASE PARAlWHZRS 
INIT. DATARASE P ARAMETERS (Cont’d) 
G. Illi- LcRTablcs 
Prog- Steps 
If LCR Tables need to be initiaked: 
1, Press the LCR Tables flexible button [But- 
ton #?I. The following message wiIl be 
shown on the display phone: 
2.To Mtialize the LCR Tables, press the 
HOLD button. Confknation tone will be 
heard. Description 
l%e XR Tables may be initialized setting all 
tables to their orfgtial, default values. The fol- 
lowing tables wiII be reset ta their original de- 
fault value a&r inMalimtion of the LCR tables: 
l 3-Digit Table 
l 6-D&$ Table 
l Exception Table 
l Route List Table 
l Insert/Delete Table 
l Daily Start Time Table 
l Weekly Schedule 
l Toll Information Route 
Issue 1, January 1995 
770-11  
						

							iqfmiie DVX’andDVXn 
Digital Eey Telephone Systems 
INIT. DATABASE P ARAMETEHS [Cont’d) 
H. IxMaHze Entire System and Reset (all 
paraxn&rs) 
steps IkscIipffon 
If System needs to be kMaIized: 
1. Press the System and Reset flexible button 
(&&ton #8). l%e following message will be 
shown on the display phone: 
2.To initialize the entire system database. 
press the HOLD button. The system will 
perform a bard reset. To completely initial&e the database area in- 
cluding all non-programmable parameters held 
in Dynamic FUM (DRAM) and reset the system 
also clearing any meantime errors that may 
exist this command may 
be used. The system 
will require reprogmmming of any 
customer 
specific data after using this command. This 
provides an easyway to re-initiake the system 
and clearing any meantime errors 
that may 
have accumulated inhibiting system operation 
or performance. 
770-12 
fssue 1, January 1993  
						

							iqjinife DVX I and DVX ’ 
nrgital SeJr Telephone Systtme 
-DATAaAsE PARAMETERS 
INIT. DATAEASE P- RS (Co&d) 
I. Initiallzc ICLID Paranleters 
Programmiq steps 
If the ICUD Tablets) need to be initialized: 
1. Press the ICLID TABLE 
fkxlble button 
(Button #9). The following message w.Ul be 
shown on the display phone: 
Description 
The ICLJD Table parameters may be initialized 
setting all data fields to their original, default 
values. 
2.To f.niMke the KWD Table[s). press the 
HOLD button. Confirmation tone will be 
heard. 
i PROGRAMCODE BEN 
FEATURE DEFAULTVALUE 
i FLASH43 .I (after inititid 
1 ICLID Rfnm Assi@mm-ks 
I No stations are assi@ed 
FlASH 56 1 
1 ICLID Enable/Disable 
2 
f ICLJD Name Entry 
3 1 ICLID Baud Rate Display 
! 4 i ICLID PotiAssi@ment Disabled 
Number is shown on LCD 
2400 Baud 
Port #l 
Issue 1, Japuarg 1993 
770-13