GE Vivid 7 Service Manual

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 8 - Replacement Procedures 8 - 63
8-9-11 Record TCP/IP Setti ngs - Software Version v2.x
1.) Select Connectivity .
2.) Select the  Tcpip tab.
3.) Record all settings in  Table 8-16 Record settings from Tcpip screen (v2.x) on page 8-63 .
 
 
Figure 8-57   TCP/IP Example Settings
Table 8-16    Record settings from Tcpip screen (v2.x)
PARAMETERVALUE
Computer Name VIVID7-00 _ _ _ _ AE Title VIVID7-00 _ _ _ _
IP Settings
IP Address_ _ _ . _ _ _ . _ _ _ 
Subnet mask_ _ _ . _ _ _ . _ _ _ 
Default Gateway_ _ _ . _ _ _ . _ _ _ 
Remote Archive Setup
Remote Archive IP-Addr _ _ _ . _ _ _ . _ _ _ Remote Archive Name 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
8 - 64 Section 8-9 - Software Loading Procedure - Software Version v2.x
8-9-12 Record Default Dataflow - Software Version v2.x
1.) In the  Connectivity  window, select  Dataflow.
2.) Verify that Default  Dataflow is selected.
3.) Record Default Dataflow Name in table  Table 8-17 on page 8-64.
  Figure 8-58   Select Dataflow
Table 8-17    Record Default Dataflow Name
DEFAULT DATAFLOW NAME 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 8 - Replacement Procedures 8 - 65
8-9-13 Record Standard Printer IP and  Port Settings - Software Version v2.x
1.) In Connectivity  window, select  Services.
2.) In the  Services list, Scroll down until  Standard Print appears.
3.) Select  Standard Print .
4.) Select  Open.
5.) Select  Printer to open the Printer scroll down menu.
6.) Select  Properties from the Printer scroll down menu.Figure 8-59   Choosing Standard Print
Figure 8-60   Properties
CONNECTIVITY
STANDARD PRINT
OPEN
SERVICES
SCROLL DOWN MENU
PRINTER
PROPERTIES 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
8 - 66 Section 8-9 - Software Loading Procedure - Software Version v2.x
8-9-13      Record Standard Printer IP and  Port Settings - Software Version v2.x (cont’d)
7.) Select  Ports.
8.) Select  Standard TCP\IP Port .
9.) Select  Configure Port .Figure 8-61   Configure Port
Figure 8-62   Configure Port (Port Settings dialog)
STANDARD TCP\IP PORT
CONFIGURE PORT
PORTS 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 8 - Replacement Procedures 8 - 67
8-9-13      Record Standard Printer IP and  Port Settings - Software Version v2.x (cont’d)
10.) Select and record  Printer Name or IP Address  in Table 8-18 on page 8-67 .
11.) Select  Raw.
12.) Select and record  Port Number in Table 8-18 on page 8-67 .
13.) Select  Cancel.
14.) Close rest of the Windows by selecting  Ok.
Table 8-18    Printer Name or IP Address and Port Number
PRINTER NAME OR IP ADDRESSPORT NUMBER
Figure 8-63   Configure Port
PORT 
NUMBER
OK
PRINTER 
NAME OR IP 
ADDRESS 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
8 - 68 Section 8-9 - Software Loading Procedure - Software Version v2.x
8-9-13-1 Record Service Settings - Software Version v2.x 1.) Select Service.
.
2.) Record Video Setting Format and VCR Type in  Table 8-19 Video Settings and VCR Type on 
page 8-68 .
 
Figure 8-64   Service Settings
Table 8-19    Video Settings and VCR Type
Video Setting FormatVCR Type 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 8 - Replacement Procedures 8 - 69
8-9-13-2 Information on the About tab - Software Version v2.x 1.) Select the  About tab.
2.) Record Application software version, System  software version and Processor model (BEP) in Table 
8-20 Record Software and hardware versions on page 8-69 .
 
Figure 8-65   Information available on the About tab
Table 8-20    Record Software and hardware versions
DESCRIPTIONRECORD VERSION
APPLICATION SW SYSTEM SW
PROCESSOR (BEP) 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
8 - 70 Section 8-9 - Software Loading Procedure - Software Version v2.x
8-9-14 Software Loading - Software Version v2.x
8-9-14-1 Overview This software loading procedure covers: 
• Installation of BT’02 Software (application software version v2.x) on Vivid 7 units.
 
Refer to Table 8-20 on page 8-69  where you recorded the unit’s software versions.
The software for Vivid 7 is divided on two CDs, one CD with the System Software and one with the 
Application Software. Table 8-21    Vivid 7 Models Versus Minimum Software Requirement
GE VINGMED 
PART NUMBER
DESCRIPTION
APPLICATION SOFTWARE  VERSION
FB000030 VIVID 7 (BT’01) V2.3.1 (or higher)
FC000060 VIVID 7 (BT’01) V2.3.1 (or higher)
FC000180 VIVID 7 PRO (BT’02) V2.3.1 (or higher)
FC000190VIVID 7 PRO (BT’02)V2.3.1 (or higher)
FC000200VIVID 7 (BT’02)V2.3.1 (or higher)
FC000210VIVID 7 (BT’02)V2.3.1 (or higher) 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 8 - Replacement Procedures 8 - 71
8-9-14-2 Vivid 7 System Software Loading - Software Version v2.x 1.) Insert the applicable  Vivid 7 System Software CD  into the CD drive, see Table 8-20 Record 
Software and hardware versions on page 8-69 .
2.) Power down the System, see  4-2-3 Power Shut Down on page 4-7 .
3.) Wait until the LCD’s on the Operator Panel are s witched off and the ON/Standby switch has turned 
amber.
4.) Power ON the System, see  4-2-2 Power ON/ Boot UP on page 4-3 . The scanner will now boot 
from the CD you inserted.
Figure 8-66   BIOS loading example 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
8 - 72 Section 8-9 - Software Loading Procedure - Software Version v2.x
8-9-14-2              Vivid 7 Syst em Software Loading - Software Version v2.x (cont’d)
5.) When requested, enter the missing part of the Co mputer Name (the unit’s serial number) as you 
recorded it in  Table 8-16 Record settings from Tcpip screen (v2.x) on page 8-63 . 
Example:  VIVID7-001890  Always enter two zeros before you enter the serial  number. This means that when you have a serial 
number which is 1890 you enter 001890. When  the serial number is 1123 you enter 001123.
6.) In this step, you can choose if you want to do a co mplete Vivid 7 installation or if you only want to 
update or reinstall the software on the C: partition (C: drive). 
Usually it should be  OK to select “B” to update the C-drive only . This will keep Presets etc. 
a.) Press  B to update/re-install the softw are on the C: partition. (Only data on the C: partition will 
be erased. System configurations et c. will be kept.) Continue with step 7.
b.) Use ONLY if a “B” update cannot be used: Press  A to do a complete Vivid 7 software 
installation. (All data will be erased.)
c.) Press  C to Exit.
 
Figure 8-67   Serial Number entry example
NOTICEIf you select “ A” in the next step, ALL existing software  and data on the hard disk will be erased. If 
backup has not been performed as described earlier in this manual, all data like Patient Database, 
System Configuration and User Configur ations (Customer Presets), will be lost.
Figure 8-68   Info entry page
Enter the Serial 
Number here
Press A, B or C to 
choose the wanted 
option.