GE Vivid 7 Service Manual

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 9 - Renewal Parts 9 - 35
9-15-2 CRT Monitor
Figure 9-14   CRT Monitor Assembly
Table 9-27    CRT Monitor Parts   
ITEMPART NAMEPART NUMBERDESCRIPTIONQTYFRU
1 P9534WA CRT MONITOR ASSY 2283334-4
OR
2283334-5 OPEN FRAME 17” MONITOR 1 Y
2 MON CABLE ASSY 2304171 MONITOR CABLE ASSEMBLY
1Y
3 P9536AL MON-REAR-NSP-ASSY 2303931MONITOR REAR COVER ASSEMBLY (WITHOUT 
SPEAKERS) 1Y
4MON CAP ASSY2303932MONITOR SCREW CAPS.2Y
5MON FRONT ASSY2303929
MONITOR FRONT BEZEL ASSEMBLY
INCLUDES THREE LOGOS, Vivid 7, LOGIQ 7 and 
LOGIQ 9.
- PLEASE CHOOSE THE APPROPRIATE LABEL 
AND ATTACH IT TO THE MONITOR FRONT 
BEZEL. 
- DISCARD THE OTHER LABELS.
1Y
6P9534WK USER SW ASSY OF 
MONITOR 2297050MONITOR SWITCH ASSEMBLY1Y
STEREO GLASSES FOR 3D 
VISUALIZATION FD200123 USED TOGETHER WITH THE 4D LV FUNCTION 1 Y
Logo Label
NOT 
ILLUSTRATED
NOT 
ILLUSTRATED
1
2
3
4
5
6 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
9 - 36 Section 9-16 - Casters
Section 9-16
Casters
 
Figure 9-15   Casters
Table 9-28    Casters 
ITEMPART NAME
PART 
NUMBER
DESCRIPTIONQTYFRU
1 CASTER FRONT 2293008-2FRONT CASTER WITHOUT SWIVEL LOCK ASSEMBLY.
2Y
2 CASTER REAR 2 293008-3REAR CASTER WITH SWIVEL LOCK ASSEMBLY.
2Y
3 CASTER HUB CAPS 2293008-5 Need to order 2 per caster, adhesive mounting 1 Y
12
3 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 9 - Renewal Parts 9 - 37
Section 9-17
Brake Assembly
Figure 9-16   Brake Assembly and Console Lock
Table 9-29    Brake Assembly 
ITEMPART NAME
PART 
NUMBER
DESCRIPTIONQTYFRU
1 PEDAL ASSEMBLY
FB200595Brake Pedal Assembly
1Y
PEDAL ASSEMBLY FD200002Brake Pedal Assembly
REPLACEMENT FOR FB200595 1Y
2 ROD CONNECTION BRAKE LEFT  FB307471 1 Y
3ROD CONNECTION BRAKE RIGHT FB3074721Y
4SCREW, PT FASTENER M6 X12MM 
WN1411 080X0612PARKING BRAKE PEDAL SCREWS 
FRONT BUMPER SCREWSY
1 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
9 - 38 Section 9-18 - Front-End Processor Card Cage
Section 9-18
Front-End Processor Card Cage
9-18-1 Introduction
Two versions of the Front-End Processor have been used;
• Front-End Processor Version 1 (FEP1), see page  9-42.
• Front-End Processor Version 2 (FEP2), see below.
9-18-2 Hardware/Software Versions,  Front-End Processor Version 2 (FEP2)
This overview is valid for the following Vivid 7 models:
• BT’03-RFI: FC000410, FC000420, FC000430, FC000440
• BT’04: FC000610, FC000620, FC000630,  FC000640, FC000650, FC000660, FC000699
• BT’05: FC000760, FC000770, FC000780, FC 000790, FC000800, FC000810, FC000820, 
FC000830, FC000840, FC000850 
• BT’06:FC000890, FC000900, FC000910, FC 000920, FC000930, FC000940, FC000950, 
FC000960, FC000970, FC000980
• BT’08: FD000010, FD000020, FD000120, FD 000130, FD000140, FD000150, FD000160, 
FD000170, FD000180, FD000190
Use  Ta b l e 9 - 3 0  to verify the correct/needed revision on each card in the FEP2.
 
Table 9-30    Required Revisions for Cards and Modules, FEP2   sheet 1 of 2
2nd VERSION OF FRONT-END CARD CAGE (FEP2)
PART 
NUMBER
NAME
BT’03 
(SW. v3.2.x/ v3.4.x/
v3.6.x)
BT’04 
(SW. v4.x)BT’05
(SW. v5.x)BT’06
(SW. v6.x)BT’08
(SW. v7.x)
COMMENTS
MCDMCDMCDMCDMCD
FC200230 BACK-
PLANE 02 02 02 02 02
FB200060 RLY-3 07 07 07 07 07 RELAY BOARD VERSION 3
- MCD REV 14 Value of internal fuse increased 
to solve issue that Pedof probe is not 
recognized due to defective fuse.
- MCD REV 13 includes a noise fix for noise in 
Color Flow that was a result of changes on 
MCD rev 12.
- MCD REV 11 includes a noise-fix to avoid 
noise in CW duplex with M3S probe.
- MCD REV 09 includes a noise-fix for M3S 
probe- MCD REV 08 has LEDs for +5V and 
+12V.
FC200314 RLY-4 N/A 02 02 02 02 RELAY BOARD VERSION 4 
TO BE USED IN UNITS WITH 3D
FC200057RX128-40202020202RECEIVER BOARD VERSION 4 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 9 - Renewal Parts 9 - 39
FC200459TX128-503
03 
(requires 
software 
v4.2.0 or  later)
030303
TRANSMITTER BOARD VERSION 5
2X TO BE USED IN UNITS WITH RT3D/4D
NOTE! Do not install one FC200459 and one  FC200375 in the same Vivid 7.
- MCD REV 07 DOC. ERROR FIX.
- MCD REV 06 Improved Manufacturing 
process. 
- MCD REV 05 Improved tolerances. 
(Manufacturing).
- MCD REV 04 Removed unused components.
- MCD REV 03 is the first released version of 
this card.
FC200375TX128-40103030303
TRANSMITTER BOARD VERSION 4
2X TO BE USED IN UNITS WITH RT3D/4D.
NOTE! Do not install one FC200459 and one  FC200375 in the same Vivid 7.
FC200239 XDBUS-3 01 01 01 01 01 TRANSDUCER BUS BOARD VERSION 3 
2X USED 
FC200364 XDBUS-4 N/A 01 01 01 01 TRANSDUCER BUS BOARD VERSION 4
2X USED
TO BE USED IN UNITS WITH RT3D/4D
FC200100 BF64 WITH 
4 MLA 01 01 01 01 01
2X USED
FC200054RFI04N/AN/AN/AN/A
INTRODUCED 2003. 
FOR UNITS WITHOUT SUPPORT FOR 3D 
OPTION.
OBSOLETE, PLEASE ORDER FC200507
FC200507RFI0102020202CARD WITH SUPPORT FOR 3D OPTION
FA200945POWER, DC0202020202
Issues on some systems when using 3V 
PROBE in CW. mode.
OBSOLETE, PLEASE ORDER FD200041
FD200041 POWER, DC 01 01 01 01 01 Increased +6VDC output current for use with 
3V PROBE in CW mode.
FB200574 POWER, TX 
(TXPS) 02 N/A N/A N/A N/A BT’03:
USED IN ALL SYSTEMS 
BT’04 and later:
DON’T USE. 
FC200386 POWER, TX 
(TXPS)  N/A 03030303 BT’04 and later: 
TO BE USED IN ALL SYSTEMS.
Table 9-30    Required Revisions for Cards and Modules, FEP2 (cont’d) sheet 2 of 2
2nd VERSION OF FRONT-END CARD CAGE (FEP2)
PART 
NUMBER
NAME
BT’03 
(SW. v3.2.x/ v3.4.x/
v3.6.x)
BT’04 
(SW. v4.x)BT’05
(SW. v5.x)BT’06
(SW. v6.x)BT’08
(SW. v7.x)
COMMENTS
MCDMCDMCDMCDMCD 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
9 - 40 Section 9-18 - Front-End Processor Card Cage
9-18-3 Front-End Processor  Version 2 FRU Parts
 
 
Figure 9-17   PCB Boards FEP2
12
3
4567
89
10
12
13
1415
16
17 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 9 - Renewal Parts 9 - 41
9-18-3 Front-End Processor Vers ion 2 FRU Parts (cont’d)
Table 9-31    PCB Boards used in FEP- 2
ITEMPART NAME
PART 
NUMBER
DESCRIPTIONQTYFRU
1 RLY-3_MODULE FB200060RELAY PCB, VERSION 3 1 Y
2 RLY-4 FC200314RELAY PCB, VERSION 4. INTRODUCED 2004 1 Y
3 RX 128 BOARD VER. 4 FC200057PCB RX-128-4, RECEIVER PCB, VERSION 4 1 Y
4TX128-5FC200459
PCB TX-128-5, VERSION 5 - USED ON FEP2 (RFI)
WITHOUT 4D: 1X USED 
Introduced 2005 for use on new systems.
1Y
5TX128-5FC200459PCB TX-128-5, VERSION 5 - USED ON FEP2 (RFI) WITH 4D: 2X USED 
Introduced 2005 for use on new systems.2Y
6TX128-4, TX-BOARD FOR RFIFC200375PCB TX-128-4, VERSION 4 - USED ON FEP2 (RFI) WITHOUT 4D: 1X USED1Y
7 TX128-4, TX-BOARD FOR RFI FC200375PCB TX-128-4, VERSION 4 - USED ON FEP2 (RFI)
WITH 4D: 2X USED 2Y
8 XD BUS 3  FC200239TRANSDUCER BUS PCB, VERSION 3 - USED ON 
FEP2 2Y
9 XD BUS 4 FC200364TRANSDUCER BUS PCB, VERSION 4 - USED ON 
FEP2 on units with 4D
10MODULE BF64_4MLAFC200100BEAM FORMER PCB2Y
12RADIO FREQUENCY INTERFACEFC200507RADIO FREQUENCY INTERFACE PCB - USED ON  FEP2-BT041Y
13POWER SUPPLY DC
FA200945DC POWER SUPPLY (OBSOLETE)1N
FD200041 DC POWER SUPPLY WITH INCREASED CURRENT 
OUTPUT ON +6VDC 1Y
14 TRANSMITTER PS SWITCHED 
MODE FB200574
TRANSMITTER POWER SUPPLY SWITCHED MODE
FOR UNITS WITH SOFTWARE VERSION v3.2.x 1Y
15 POWER, TX FC200386TRANSMITTER POWER SUPPLY SWITCHED MODE
 FOR UNITS WITH SOFTWARE VERSION v4.x / v5.x 1Y
16NUT PANEX STUDS 080B2000RETAINER RECEPT (7 places)7Y
17CARD-RACK COMPLETEFC200308RACK W/ MOTHERBOARD
FEP2 (INTRODUCED 2ND HALF 2003)1Y 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
9 - 42 Section 9-18 - Front-End Processor Card Cage
9-18-4 Hardware/Software Versions , Front-End Processor Version 1
This overview is valid for the following Vivid 7 models:
• FC000030, FC000060
• FC000180, FC000190, FC000200, FC000210
• FC000310, FC000320, FC000330, FC000340
Use Ta b l e 9 - 3 2  to verify the correct/needed revision on each card in the Card Rack (FEP1).
NOTE: Units with FEP1 can’t be upgraded to software  version 4.0.0 or higher. For software version 
4.0.0 the RFI card in FEP2 is required.
 
Table 9-32    Required Revisions for Card s and Modules, Front-End Processor V1 (FEP1)
1st VERSION OF FRONT-END PROCESSOR CARD CAGE (FEP1)
PART 
NUMBER
NAME
v2.3.x/ v2.4.x
v3.1.x/
v3.3.x/ v3.5.x 
COMMENTSMCDMCD
FA200985 BACKPLANE 
(MOTHERBOARD) 02 02
FB200060 RLY-3 06 06 - MCD REV 07 INCLUDES A NOISEFIX FOR USE OF TEE PROBE.
- MCD REV 08 has LEDs for +5V and +12V.
- MCD REV 09 includes a noise-fix for M3S probe
- MCD REV 11 includes a noise-fix to 
avoid noise in CW duplex with M3S 
probe.
- MCD REV 14 Value of internal fuse increased to solve issue that Pedof 
probe is not recognized due to defective fuse. 
FB200170 TX128-2. B N/A FOR VIVID 7. Used before 2003.
FC200022TX128-30101
REPLACEMENT FOR FB200170. PHASED INTO MANUFACTURING  SECOND HALF OF 2002. 
NEEDED FOR ALL BT’03 UNITS WITH SOFTWARE VERSION V3.1.x.
FC200459TX128-5N/A03REQUIRES SOFTWARE VERSION V3.5.X
FB200831RX128-3BA,BN/A
FC200057 RX128-4 02 02 This card is compatible with Vivid 7 systems at Rev. v2.3.0/v2.4.0 and up.
FB200158 XDBUS-2 02 N/A 2X USED 
FB200900 BF64 C/D/E N/A 2X USED
FC200100BF64 WITH 4 MLAN/A01 2X USED
FB200165FEC-II03, 0403, 04
FB200140RFT1B, C, DN/ABOTH MCD REV. B, C AND D MAY BE USED.
FC200394 RFT1 N/A E IMPROVED GREYSCALE (COMPARED TO FB200140)
REQUIRES V3.1.x SOFTWARE
FB200865 SDP 02 02
FB200991 IMP-2B A,B A,B
FC200120IMP-30101REPLACES FB200991 REQUIRES BEP2
FA200945POWER, DC0202OBSOLETE, Please order FD200041
FD200041POWER, DC0101REPLACES FA200945 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
Chapter 9 - Renewal Parts 9 - 43
FB200574 POWER, TX (TXPS) 03 03
Table 9-32    Required Revisions for Ca rds and Modules, Front-End Processor V1 
1st VERSION OF FRONT-END PROCESSOR CARD CAGE (FEP1)
PART 
NUMBER
NAME
v2.3.x/ v2.4.x
v3.1.x/
v3.3.x/ v3.5.x 
COMMENTSMCDMCD 
						

							
GE HEALTHCARE
DIRECTION FC091194, REVISION 11    VIVID 7 SERVICE MANUAL 
9 - 44 Section 9-18 - Front-End Processor Card Cage
9-18-5 Front-End Processor  Version 1 FRU Parts
 
 
Figure 9-18   PCB Boards - FEP1
1
23
6
78
9
1011
12
1314
15
16
17
18
4a4b4c