Konica Minolta bizhub 362 User Manual

							3Basic copy operation
3-26 362/282/222
Basic copy operation
Chapter 3
2Select the paper tray 
loaded with the desired 
paper.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-27
Basic copy operation
Chapter 3
3.6 Specifying a Zoom setting
The zoom ratio can be set in order to make a copy on paper with a size dif-
ferent than the document or to enlarge or reduce the size of the copy image.
The following procedures describe how to specify the Zoom setting.
2
Note 
The factory default setting is “×1.0”. 
As a factory default, the “Auto Zoom” setting and the “Auto Paper Select” 
setting cannot both be selected at the same time. If the “Auto Zoom” set-
ting is selected while the “Auto Paper Select” setting was selected, the 
Paper screen appears. In the Paper screen, specify the desired Paper 
setting.
However, the software switch settings can be used to allow the “Auto 
Zoom” setting and the “Auto Paper Select” setting to be selected at the 
same time. For details on the software switch settings, refer to “Specify-
ing software switch settings (machine functions)” on page 11-50.
Automatically selecting the zoom ratio (“Auto Zoom” setting)
The most appropriate zoom ratio is automatically selected based on the size 
of the loaded document and the specified paper size.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-28 362/282/222
Basic copy operation
Chapter 3
2Touch [Auto Zoom].
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-29
Basic copy operation
Chapter 3
Specifying the same zoom ratio as the document (“×1.0” setting)
A copy that is the same size as the document (×1.000) is produced.
0Touch   to enlarge the zoom ratio, and touch   to reduce the 
zoom ratio in ×0.001 increments.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch [×1.0].
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-30 362/282/222
Basic copy operation
Chapter 3
Slightly reducing the copy (“Minimal” setting)
A document image can be printed slightly smaller (×0.930) than the original 
document size.
0The zoom ratio of the “Minimal” setting can be changed (between ×0.900 
and ×0.999). For details on changing the zoom ratio for the “Minimal” set-
ting or programming custom zoom ratios, refer to “Storing the desired 
zoom ratio” on page 3-37.
0Touch   to enlarge the zoom ratio, and touch   to reduce the 
zoom ratio in ×0.001 increments.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch [Minimal].
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-31
Basic copy operation
Chapter 3
Finely adjusting the zoom ratio
The zoom ratio can be finely increased or reduced in ×0.001 increments in 
order to copy at the desired size.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Adjust the zoom ratio.
– Touch   to in-
crease the zoom ra-
tio, and touch   
to reduce the zoom 
ratio.
– The zoom ratio is in-
creased or reduced 
in ×0.001 incre-
ments.
– Hold down the but-
ton to change the 
zoom ratio in larger increments.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-32 362/282/222
Basic copy operation
Chapter 3
Selecting a preset zoom ratio (Enlarge and Reduce settings)
The most suitable zoom ratios for copying from common standard document 
sizes to standard paper sizes are preset.
0Touch   to enlarge the zoom ratio, and touch   to reduce the 
zoom ratio in ×0.001 increments.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch the button for the 
appropriate zoom ratio 
according to the docu-
ment and paper sizes.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-33
Basic copy operation
Chapter 3
Typing in the zoom ratio
By using the keypad, a zoom ratio between ×0.250 and ×4.000 can be typed 
in directly without changing the height-to-width ratio.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
2Touch [XY Zoom].
The XY Zoom screen ap-
pears.
3Using the keypad, type 
in the desired zoom ra-
tio.
– If a value outside the 
allowable range is 
specified, the mes-
sage “Input Error” 
appears. Type a val-
ue within the allowa-
ble range.
– If the value was in-
correctly entered, 
press the [C] (clear) key in the keypad to erase the value, and then 
specify the correct value.
Downloaded From ManualsPrinter.com Manuals 
						

							3Basic copy operation
3-34 362/282/222
Basic copy operation
Chapter 3
4Touch [Enter].
The Zoom screen appears again.
!
Detail 
The enter zoom ratio can be stored. For details on storing zoom ratios, 
refer to “Storing the desired zoom ratio” on page 3-37.
Specifying separate horizontal and vertical zoom ratios (Individual 
Zoom settings)
By using the keypad, separate zoom ratios can be typed in directly for the 
horizontal direction (between ×0.250 and ×4.000) and for the vertical direc-
tion (between ×0.250 and ×4.000).
By changing the horizontal and vertical zoom ratios, the copy image can be 
resized as shown in the following illustration.
1In the Basics screen, 
touch [Zoom].
The Zoom screen ap-
pears.
Downloaded From ManualsPrinter.com Manuals 
						

							Basic copy operation3
362/282/222 3-35
Basic copy operation
Chapter 3
2Touch [XY Zoom].
The XY Zoom screen ap-
pears.
3Touch [Individual Zoom].
The Individual Zoom 
screen appears.
4Using the keypad, type 
in the desired zoom ra-
tios for side X and side Y 
(between ×0.250 and 
×4.000).
– If a value outside the 
allowable range is 
specified, the mes-
sage “Input Error” 
appears. Type a val-
ue within the allowa-
ble range.
– If the value was incorrectly entered, press the [C] (clear) key in the 
keypad to erase the value, and then specify the correct value.
5Touch [Enter].
The Zoom screen appears again.
Downloaded From ManualsPrinter.com Manuals