Konica Minolta bizhub 362 User Manual

							9Replacing toner bottles and staples and emptying punch waste containers
9-24 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
9.4 Emptying the waste containers
If the hole-punch waste container in punch unit installed on finisher becomes 
full, the message shown below appears. 
To empty the hole-punch waste container
Follow the procedure described below to empty the hole-punch waste con-
tainer.
1Open the front door.
Downloaded From ManualsPrinter.com Manuals 
						

							Replacing toner bottles and staples and emptying punch waste containers9
362/282/222 9-25
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
2Pull out the hole-punch 
waste container.
3Empty the hole-punch 
waste container.
4Insert the hole-punch waste container at its original position.
5Close the front door.
Downloaded From ManualsPrinter.com Manuals 
						

							9Replacing toner bottles and staples and emptying punch waste containers
9-26 362/282/222
Replacing toner bottles and staples and emptying punch waste containers
Chapter 9
Downloaded From ManualsPrinter.com Manuals 
						

							10
Care of the machine
Chapter 10
Care of the machine
Downloaded From ManualsPrinter.com Manuals 
						

							10Care of the machine
10-2 362/282/222
Care of the machine
Chapter 10
10 Care of the machine
10.1 Cleaning
This section describes the procedures for cleaning each part.
Housing
%Clean the surface of the 
housing by wiping it with 
a soft cloth dampened 
with a mild household 
detergent.
2
Reminder 
B e  s u r e  t o  t u r n  o f f  t h e  m a c h i n e  (set the main power switch to “o”) before 
cleaning it.
Never use solvents, such as benzene or thinner, to clean the housing.
Downloaded From ManualsPrinter.com Manuals 
						

							Care of the machine10
362/282/222 10-3
Care of the machine
Chapter 10
Original glass
%Clean the surface of the 
original glass by wiping it 
with a soft, dry cloth.
2
Reminder 
Never use solvents, such as benzene or thinner, to clean the original 
glass.
Downloaded From ManualsPrinter.com Manuals 
						

							10Care of the machine
10-4 362/282/222
Care of the machine
Chapter 10
Control panel
%Clean the control panel 
by wiping it with a soft, 
dry cloth.
2
Reminder 
Pressing too hard on a key in the control panel or on the touch panel may 
damage them. In addition, never use a mild household detergent, glass 
cleaner, benzene or thinner to clean the control panel or touch panel.
!
Detail 
When cleaning the control panel, displaying the Panel cleaning screen 
may prevent incorrect operations from being performed. For details, refer 
to “Panel Cleaning” on page 11-20.
Downloaded From ManualsPrinter.com Manuals 
						

							Care of the machine10
362/282/222 10-5
Care of the machine
Chapter 10
Document pad
%Clean the document pad 
by wiping it with a soft 
cloth dampened with a 
mild household deter-
gent.
Left partition glass
Clean the Left partition glass when the optional ADF is installed.
%Clean the Left partition 
glass by wiping it with a 
soft, dry cloth.
2
Reminder 
Never use solvents, such as benzene or thinner, to clean the Left partition 
glass.
Downloaded From ManualsPrinter.com Manuals 
						

							10Care of the machine
10-6 362/282/222
Care of the machine
Chapter 10
10.2 Viewing counters (Total Counter)
The Total Counter screen can be displayed so that the total number of prints 
since counting started can be viewed.
To view the contents
1Press the [Utility/Counter] key.
2Touch [Check Detail].
The Counter screen appears.
3Touch [Exit], and then touch [Enter] in the next screen that appears.
The Basic screen appears again.
2
Note 
In the Counter screen, touch [Fwd] to display the next screen, or touch 
[Back] to display the previous screen.
Downloaded From ManualsPrinter.com Manuals 
						

							Care of the machine10
362/282/222 10-7
Care of the machine
Chapter 10
10.3 When the message “Preventative Maintenance is re-
quired.” appears
If the message “Preventative Maintenance is required.” appears, contact 
your service representative and request a periodic maintenance inspection.
Downloaded From ManualsPrinter.com Manuals