Konica Minolta bizhub 362 User Manual

							Introduction
x-30 362/282/222
Downloaded From ManualsPrinter.com Manuals 
						

							1
Installation and operation precautions
Chapter 1
Installation and operation 
precautions
Downloaded From ManualsPrinter.com Manuals 
						

							1Installation and operation precautions
1-2 362/282/222
Installation and operation precautions
Chapter 11 Installation and operation precautions
1.1 Safety information
This section contains detailed instructions on the operation and maintenance 
of this machine. To achieve optimum utility of this device, all operators 
should carefully read and follow the instructions in this manual.
Please read the following section before connecting the machine to the sup-
ply. It contains important information related to user safety and preventing 
equipment problems.
Please keep this manual in a handy place near the machine.
Make sure you observe all of the precautions appear in each section of this 
manual.
KM_Ver.02E
2
Note 
Some parts of the contents of this section may not correspond with the 
purchased product.
Warning and precaution symbols 
The following indicators are used on the warning labels or in this manual to 
categorize the level of safety warnings.
Meaning of symbols
WARNINGIgnoring this warning could cause serious injury 
or even death.
CAUTIONIgnoring this caution could cause injury or dam-
age to property.
A triangle indicates a danger against which you should take pre-
caution.
This symbol warns against cause burns.
A diagonal line indicates a prohibited course of action.
This symbol warns against dismantling the device.
A solid circle indicates an imperative course of action.
This symbol indicates you must unplug the device.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and operation precautions1
362/282/222 1-3
Installation and operation precautions
Chapter 1
Disassemble and modification
WARNING
• Do not attempt to remove the covers and pan-
els which have been fixed to the product. Some 
products have a high-voltage part or a laser 
beam source inside that could cause an electri-
cal shock or blindness.
• Do not modify this product, as a fire, electrical 
shock, or breakdown could result. If the prod-
uct employs a laser, the laser beam source 
could cause blindness.
Power cord
WARNING
• Use only the power cord supplied in the pack-
age. If a power cord is not supplied, only use 
the power cord and plug that is specified in 
POWER CORD INSTRUCTION. Failure to use 
this cord could result in a fire or electrical 
shock.
• Use the power cord supplied in the package 
only for this machine and NEVER use it for any 
other product. Failure to observe this precau-
tion could result in a fire or electrical shock.
• Do not scratch, abrade, place a heavy object 
on, heat, twist, bend, pull on, or damage the 
power cord. Use of a damaged power cord (ex-
posed core wire, broken wire, etc.) could result 
in a fire or breakdown.
Should any of these conditions be found, im-
mediately turn OFF the power switch, unplug 
the power cord from the power outlet, and then 
call your authorized service representative.
Downloaded From ManualsPrinter.com Manuals 
						

							1Installation and operation precautions
1-4 362/282/222
Installation and operation precautions
Chapter 1
Power source
WARNING
• Use only the specified power source voltage. 
Failure to do that could result in a fire or electri-
cal shock.
• Connect power plug directly into wall outlet 
having the same configuration as the plug. Use 
of an adapter leads to the product connecting 
to inadequate power supply (voltage, current 
capacity, grounding), and may result in fire or 
shock. If proper wall outlet is not available, the 
customer shall ask qualified electrician for the 
installation.
• Do not use a multiple outlet adapter nor an ex-
tension cord in principle. Use of an adapter or 
an extension cord could cause a fire or electri-
cal shock. 
Contact your authorized service representative 
if an extension cord is required.
• Consult your authorized service representative 
before connecting other equipment on the 
same wall outlet. Overload could result in a fire.
CAUTION
• The outlet must be near the equipment and 
easily accessible. Otherwise you can not pull 
out the power plug when an emergency occurs.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and operation precautions1
362/282/222 1-5
Installation and operation precautions
Chapter 1
Power plug
WARNING
• Do not unplug and plug in the power cord with 
a wet hand, as an electrical shock could result.
• Plug the power cord all the way into the power 
outlet. Failure to do this could result in a fire or 
electrical shock.
CAUTION
• Do not tug the power cord when unplugging. 
Pulling on the power cord could damage the 
cord, resulting in a fire or electrical shock.
• Remove the power plug from the outlet more 
than one time a year and clean the area be-
tween the plug terminals. Dust that accumu-
lates between the plug terminals may cause a 
fire.
Grounding
WARNING
• Connect the power cord to an electrical outlet 
that is equipped with a grounding terminal.
Downloaded From ManualsPrinter.com Manuals 
						

							1Installation and operation precautions
1-6 362/282/222
Installation and operation precautions
Chapter 1
Installation
WARNING
• Do not place a flower vase or other container 
that contains water, or metal clips or other 
small metallic objects on this product. Spilled 
water or metallic objects dropped inside the 
product could result in a fire, electrical shock, 
or breakdown.
Should a piece of metal, water, or any other 
similar foreign matter get inside the product, 
immediately turn OFF the power switch, unplug 
the power cord from the power outlet, and then 
call your authorized service representative.
CAUTION
• After installing this product, mount it on a se-
cure base. If the unit moves or falls, it may 
cause personal injury.
• Do not place the product in a dusty place, or a 
site exposed to soot or steam, near a kitchen 
table, bath, or a humidifier. A fire, electrical 
shock, or breakdown could result.
• Do not place this product on an unstable or tilt-
ed bench, or in a location subject to a lot of vi-
bration and shock. It could drop or fall, causing 
personal injury or mechanical breakdown.
• Do not let any object plug the ventilation holes 
of this product. Heat could accumulate inside 
the product, resulting in a fire or malfunction.
• Do not use flammable sprays, liquids, or gases 
near this product, as a fire could result.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and operation precautions1
362/282/222 1-7
Installation and operation precautions
Chapter 1
Ventilation
CAUTION
• Using this product in a poorly ventilated room 
for a long time or producing a large volume of 
copies or prints may cause the odor of exhaust 
air from the machine. Ventilate the room well.
Actions in response to troubles
WARNING
• Do not keep using this product, if this product 
becomes inordinately hot or emits smoke, or 
unusual odor or noise. Immediately turn OFF 
the power switch, unplug the power cord from 
the power outlet, and then call your authorized 
service representative. If you keep on using it 
as is, a fire or electrical shock could result.
• Do not keep using this product, if this product 
has been dropped or its cover damaged. Imme-
diately turn OFF the power switch, unplug the 
power cord from the power outlet, and then call 
your authorized service representative. If you 
keep on using it as is, a fire or electrical shock 
could result.
CAUTION
• The inside of this product has areas subject to 
high temperature, which may cause burns.
When checking the inside of the unit for mal-
functions such as a paper misfeed, do not 
touch the locations (around the fusing unit, etc.) 
which are indicated by a “Caution HOT” cau-
tion label.
Downloaded From ManualsPrinter.com Manuals 
						

							1Installation and operation precautions
1-8 362/282/222
Installation and operation precautions
Chapter 1
When the optional Fax Kit FK-503 is not installed:
Consumables
WARNING
• Do not throw the toner cartridge or toner into an 
open flame. The hot toner may scatter and 
cause burns or other damage.
CAUTION
• Do not leave a toner unit or drum unit in a place 
within easy reach of children. Licking or ingest-
ing any of these things could injure your health.
• Do not store toner units and PC drum units near 
a floppy disk or watch that are susceptible to 
magnetism. They could cause these products 
to malfunction.
When moving the machine
CAUTION
• Whenever moving this product, be sure to dis-
connect the power cord and other cables. Fail-
ure to do this could damage the cord or cable, 
resulting in a fire, electrical shock, or break-
down.
• When moving this product, always hold it by 
the locations specified in the User’s Guide or 
other documents. If the unit falls it may cause 
severe personal injury. The product may also 
be damaged or malfunction.
Before successive holidays
CAUTION
• Unplug the product when you will not use the 
product for long periods of time.
Downloaded From ManualsPrinter.com Manuals 
						

							Installation and operation precautions1
362/282/222 1-9
Installation and operation precautions
Chapter 1
1.2 USER INSTRUCTIONS 
FCC PART 15 - RADIO FREQUENCY DEVICES (For U.S.A. Users)
NOTE: This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment. 
This equipment generates, uses and can radiate radio frequency energy and, 
if not installed and used in accordance with the instruction manual, may 
cause harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his own expense.
WARNING: The design and production of this unit conform to FCC regula-
tions, and any changes or modifications must be registered with the FCC and 
are subject to FCC control. Any changes made by the purchaser or user 
without first contacting the manufacturer will be subject to penalty under 
FCC regulations.
This device must be used with shielded interface cables. The use of non-
shielded cable is likely to result in interference with radio communications 
and is prohibited under FCC rules.
INTERFERENCE-CAUSING EQUIPMENT STANDARD (ICES-003 ISSUE 
4) (For Canada Users)
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du 
Canada.
For users in countries subject to Class B regulations
For users in countries not subject to Class B regulations
This device must be used with shielded interface cables. The use of non-shielded cable is likely 
to result in interference with radio communications and is prohibited under CISPR 22 rules and 
local rules.
WARNING
This is a Class A product. In a domestic environment this product may cause radio interference 
in which case the user may be required to take adequate measures.
This device must be used with shielded interface cables. The use of non-shielded cable is likely 
to result in interference with radio communications and is prohibited under CISPR 22 rules and 
local rules.
Downloaded From ManualsPrinter.com Manuals