Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

							SECTION MITL9141-753-526-NAPage 2 
						

							Datashelf 9100
2. DATASHELF 9100
General2.01The DATASHELF 9100 is 8.75 in. high. The left side of the shelf
holds up to 16 
DATASETs, while the right side contains an
integral shelf power supply. All connections to the DATASHELF 9100
are made at the back of the shelf. Each card has connectors which are
connected directly to the device with which the 
DATASET is to cbm-municate. Each 
DATASET also has an edge connector which plugs into
the shelf backplane; this connector provides power to the card, and
connects to the backplane connector which connects tip-ring pair to
the PABX. Figure 2-l shows a front view of the DATASHELF 9100.
2.02The shelf power supply, the shelf, and the backplane are one
integral unit. The power supply provides 9 
vat to each card
connector. A 25-pair connector on the backplane connects the tip-ring
pairs from the 
DATASETs to the PABX. The power cord from the ac
distribution panel plugs into the back of the shelf, directly behind the
power supply. Figure 2-2 shows the backplane and connectors of the
DATASHELF 9100.
2.03The 
DATASET edge connectors which plug into the shelf con-
nect the tip and ring to the 25-pair connector which is cabled
to the PABX MDF. The pair assigned to each 
DATASET is listed in Table
2-1.
TABLE 2-l
DATASHELF 9100 TIP AND RING PIN ASSIGNMENTS
slot
DATASETtipringJ17 connector
tipring
Jl112261J2
112272
J3
112283
J4
112294
J5
112305J6
112316
J7
112327
J8
112338
J9112
934
JIO112
1035
Jll1121136
J12
1121237
J13112
1338
J14
1121439
J15
112
1540
J16
112
1641Page 3 
						

							SECTION MITL9141-753-526-NARACK-MOUNTED
DATASET CARDON/OFF
SWITCH
POWER
SUPPLV
KAo317m
IFigure 2-l Front View of the DATASHELF 9100
Page 4 
						

							Datashelf 9100IWMARVINIPUT FUSE
GROUND/
STUD
POWER CORDCONNECTOR
\
KA0344RZEFigure 2-2 Backplane and Connectors of the DATASHELF 9100
Page 5 
						

							SECTION MITL9141-753-526-NAPage 6 
						

							Datashelf 9100
3. DATASHELF 9100 INSTALLATION AND WIRING
Note:Each card slot not equipped with a DATASET set must be
equipped with a filler plate to maintain correct flow of cooling
air within the shelves; this does not apply to the top shelf of
any configuration.
CHART 3-1
INSTALL DATASHELF 9100 INTO A DATACABINET 9000
StepAction
1Unpack and inspect the shelf for damage or missing items.
2Turn off the DATACABINET 9000 power switch and remove the line cord from its
outlet. Open the doors of the cabinet.
3Install the cardfile rails in the bottom of the cabinet, above the fan unit, as shown
in Figure 3-1, for the first shelf being installed in the cabinet, or immediately above
an existing shelf.
4Place the shelf onto the 
cardfile rails and fasten to the front cabinet side rails with
the screws provided.
5Connect the frame ground wire from the shelf ground stud to the left side rail (as
viewed from rear) within the cabinet, as shown in Figure 3-2.
6Connect ac cords from distribution panel to the shelf and attach to left side rail
within cabinet.
7Unpack and install DATASETs into their assigned slots.
8Install signal cables to each shelf, and connect the signal cables to their associated
equipment.
9Form a cable bundle neatly up the right side rail, and attach securely to the
brackets on the side rails.
10
11
12
13Install 25-pair cable to the shelf; attach to side rail brackets separately from ac
cords. Connect the 25-pair cable to its associated MDF, and cross connect the
MDF blocks as required.
Close up the covers of the cable access slots, close and lock rear door.
Connect the power cord from the DATACABINET 9000 to its ac outlet.
Customer Data Entry for the 
DATASETs must be completed at the PABX before the
DATASETs will operate (refer to PABX Customer Data Entry Practice).
14Turn on the power switch on the PDU panel at the rear of the cabinet.
15Turn on shelf power supply, and close and lock door.
Page 7 
						

							SECTION MITL9141-753-526-NA
CARDFILE RAIL
I
FAN UNIT
KAO60 1 ROE0Figure 3-l Installation of 
Cardfile Rail
Page 8 
						

							Datashelf 9100l!L
0DATASHELF 9100
80
0DATACABINET 9000
SIDE RAIL 
-
CARDFILE
RAILII“I III0
0
0
0
0
r
0
Q0
0
III/f--L- I:: . .
Figure 3-2 Connection of Shelf Ground Wire
Page 9 
						

							MITEL STANDARD PRACTICESECTION MITL9141-753-528-NAIssue 1, April 1988
MODEM INTERCONNECT PANEL
@Copyright 1988, MITEL Corporation. All rights reserved.
T”Trademark of MITEL Corporation
@Registered Trademark of MITEL Corporationi 
						

							SECTION MITL9141-753-528-NANOTICE
The information contained in this document is believed to be accurate in all respects but is
not warranted by 
Mite1 Corporation (MITEL). The information is subject to change without
notice and should not be construed in any way as a commitment by 
Mite1 or any of its
affiliates or subsidiaries. 
Mite1 and its affiliates and subsidiaries assume no responsibility
for any errors or omissions in this document. Revisions of this document or new editions of
it may be issued to incorporate such changes.