Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

							SUPERSET 3DN Set Information
6. DATA CARTRIDGE OPERATION
General
6.01This is only a brief description of data call operations possible
with the 
SUPERSET 3DN telephone data cartridge and feature
keys.For more information on data calls, refer to Section
MITLS 109-094- 105-NA.To originate a data transceiver (DTRX) call from the 
SUPERSET 3DN
telepone:
Press the 
CALL/ATTN key.
Enter the number destination from the data terminal keyboard.
The LCD beside the 
CALL/ATTN key provides call status indication as
follows:
blank 
- no connection
circle 
- DTR (device is ready but not connected)
circle and flashing square 
- connected to DTRX or queued at
destination
solid 
- connected to called distination
To disconnect a DTRX call from the set:
Press the DATA DISC key.
Page 15 
						

							SECTION MITL9109-094-I 08-NA
Page 16 
						

							.SUPERSET 3DN Set Information
7. LINE APPEARANCES
General
7.01A line is said to “appear” at a SUPERSEJ 3DN telephone if the
line has been assigned to one of the twelve available positions
on the Line Status Display and can be selected or accessed by the set
user. A line can be programmed to appear at one set, or at more than
one set, or more than once at a particular set. Although a line can
appear more than once throughout the system, it is always identified
by its unique directory number.
7.02The appearances of a line do not have to be identical 
- the line
type and its variants can both differ; for example, a line can
appear as a Prime Line at one set and as a Key Line (with delayed ring)
at another set. However, an ONS line or 
SUPERSEJ@ prime line cannot
have both key line and Multicall line appearances.
7.03Although a SUPERSEJ 3DN telephone can have up to 12 line
appearances, it requires only only one pair of wires to connect
the set to its equipment number position. The SUPERSEJ 3DN tele-
phone sends signals to the PABX which makes the appropriate line
connection.
7.04The liquid crystal display beside the line appearance keys in-
dicates the status of each line appearance as shown in Figure
7-l.
Page 17 
						

							SECTION MITL9109-094-108-NASYMBOL
clDESCRIPTIONMEANING
NO SYMBOL IN DISPLAVLINE IDLE
4*DISPLAV ALTERNATES
INCOMING CALL
BETWEEN THESE TWO SYMBOLS
LINE BUSY
AT THIS SET DISPLAY SOLID SQUARE
DISPLAY SOLID CIRCLELINE BUSY AT
ANOTHER SET
DISPLAV ALTERNATES
BETWEEN SOLID AND CLEARCALL ON HOLD
AT THIS SET
4DISPLAV CIRCLE FLASHESCALL ON HOLD AT
ON AND OFFANOTHER SET
5634ElRlFigure 7-l Line Status Display Symbols
Page 18 
						

							SUPERSET 3DN Set Information
8. SHIPPING AND RECEIVING
General
8.01The SUPERSEJ 3DN telephone is shipped in a single carton.
8.02The SUPERSEJ 3DN telephone disassembles into main assem-
bly, handset, and handset cord. Additional items include 
iden-tification cards (for telephone numbers and lines), protective covers for
these cards, reference guide, installation guide, and warranty tag.
Delivery Check
8.03On delivery at the destination, check that all items are present
and undamaged. Retain some sets of packaging material for
reshipment of any damaged or defective items.
Page 19 
						

							SECTION MITL9109-094-l OS-NA
Page 20 
						

							SUPERSET 3DN Set Information
9. INSTALLATION
WARNING
ANY CONNECTION OF THIS SET TO AN OFF PREMISE APPLICATION,
AN OUT OF PLANT APPLICATION, OR TO ANY OTHER EXPOSED
PLANT APPLICATION MAY RESULT IN A SAFETY HAZARD, AND/OR
DEFECTIVE OPERATION, AND/OR EQUIPMENT DAMAGE.
9.01Do NOT connect SUPERSET 3DN telephones in parallel, to stan-
dard lines, or as Power Fail Transfer extensions. Do not use a
hand test telephone (butt-in) to check a 
SUPERSET 3DN telephone line,
because its Digital Line Card has no loop detector; set 
on-hook/off-hook status is signaled by data transmission.
Before a 
SUPERSET 3DN telephone can be connected to a PABX, the
PABX must be programmed and equipped with Digital Line Cards to
interface with its 
SUPERSET 3DN telephones.
Installation
9.02Install a 
SUPERSET 3DN telephone as follows:
Connect the handset cord to the handset and the main assem-
bly.
Identify the 
SUPERSET 3DN telephone set’s number, prime line number,
and other lines appearances on the telephone number identification
card.
Install the identification card and protective cover onto the main as-
sembly.
Connect the line cord to the telephone jack which connects to its
assigned Digital Line Card in the PABX.
Environmental Specifications
Operating Environment:
Ambient Temperature: 4 to 49°C (39.2 to 120°F).
Ambient Humidity: 10 to 90% RH, noncondensing.
Storage/Shipping Environment:
Ambient Temperature: -40 to 60°C (-40 to 150°F).
Ambient Humidity: 10 to 90% RH, noncondensing.
Page 
21 
						

							MITEL STANDARD PRACTICEMITL9109-094-109-NAIssue 1, April 1988
SX-200” DIGITAL
PRIVATE AUTOMATIC BRANCH EXCHANGE
SUPERSET 4TMDN TELEPHONE INFORMATION
@Copyright 1988, MITEL Corporation. All rights reserved,
T”Trademark of MITEL Corporation
@Registered Trademark of MITEL Corporation 
						

							MITL9109-094-109-NANOTICE
The information contained in this document is believed to be accurate in all respects but is
not warranted by 
Mite1 Corporation (MITEL). The information is subject to change without
notice and should not be construed in any way as a commitment by 
Mite1 or any of its
affiliates or subsidiaries. 
Mite1 and its affiliates and subsidiaries assume no responsibility
for any errors or omissions in this document. Revisions of this document or new editions of
it may be issued to incorporate such changes. 
						

							SUPERSET 4DN Telephone information
CONTENTS
PAGE1. INTRODUCTION
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Reason for Issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . 1
2. GENERAL DESCRIPTION
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. PHYSICAL DESCRIPTION
Liquid Crystal Display...................................
5Handset.............................................
5Telephone Keypad.....................................
54. FUNCTIONAL DESCRIPTION
Softkeys and SUPERKEY.....................
HOLD Key................................
SPEAKER Key.............................
MUTE Key...............................
Message LED.............................
Line Appearance Keys......................
Feature Access Keys.......................
5. TELEPHONE OPERATION
General . . . . . . . . . . . . . . .
Originating Calls . . . . . . .
Answering Calls . . . . . . . . .
Terminating A Call . . . . . . .
Call Transfer/Conferencing .
Ringer Pitch Adjustment . . .
. .
. .
. .
. .
. .
. .
..............
...............
..............
..............
..............
. . . . .
. . . . .
. . . . ,
. . . . .
. . . . .
. . . . .
. . . . .
. . .
. . .
. . .
. . .
. . .
. . .
.*.9
...9
...9
..10
..10
..10
.,10
, . . . .
. . . . .
. . . . .
, . . . .
, . . . .
. . . . .
13
13
13
13
14
146. DATA CARTRIDGE OPERATION
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7. LINE APPEARANCES
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8. PACKAGING
General 
..,......................................... 21
9. INSTALLATION AND MAINTENANCE
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . 23
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . , . . 24
LIST OF ILLUSTRATIONS
FIGURETITLE
PAGE3-lSUPERSEJ 
4TMDN Telephone.....................63-2
SUPERSEJ 4DN Telephone Faceplate...............
74-l
Line Status Display Symbols....................
11
. . .III