Panasonic DBS 576HD Technical Manual

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 6-29
To set DND for your own extension:
To cancel DND for your own extension:
To set DND for another extension:
To cancel DND for another extension:
Hardware Requirements
•N/A
Related Programming
• FF1-0-03: Extension COS (Manual DND Override Send)
• FF1-0-03: Extension COS (Forced DND Override)
• FF1-0-03: Extension COS (DND Set/Clear)
• FF1-0-03: Extension COS (DND Set/Clear Other)
• FF1-2: Dial PlanAction Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the DND Set/Cancel code (default = 720).
3.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the DND Set/Cancel code (default = 720).
3.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the DND Set by Other Phone code (default = 740).
3.   Dial the extension number.
4.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the DND Cancel by Other Phone code (default = 750).
3.   Dial the extension number.
4.   Replace the handset or press the ON/OFF key. 
						

							6-30 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
• FF3: Extension COS
Considerations
• Forced DND override is available.
• DND override function is available by Busy Override code.
DP to DTMF Signal Conversion
Description
Dial Pulse (DP) to Dual Tone Multifrequency (DTMF) Signal Conversion allows you to switch from 
DP to DTMF signaling when using a DP trunk. For instance, if you dial into a Voice Mail system 
using a DP trunk, you can switch to DTMF signaling to communicate with the Voice Mail system. 
(The System can automatically change DP to DTMF tones based on the incoming and outgoing 
timers). 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 6-31
Operation
To switch from DP to DTMF dialing:
Hardware Requirements
•N/A
Related Programming
• FF1: DTMF 
• FF2: DP to DTMF (Outgoing)
• FF2: DP to DTMF (Incoming)
Considerations
•N/A
Flash
Description
You can send a flash signal on your telephone to release an outside line and then either automatically 
reseize the same outside line or switch to extension dial tone status by pressing the FLASH key.
Trunk programming determines whether your phone reseizes the outside line or switches to extension 
dial tone status.
Hardware Requirements
•N/A
Related Programming
• FF1-1: Flash Timer
• FF2: Flash Pattern
• FF2: Flash Key Operation
• FF3: Flash on PROG (Recall)
Considerations
•N/AAction Result
1.   Press the * key or the # key. 
						

							6-32 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Hot Line
Description
Hot Line enables you to immediately connect to another pre-assigned extension or speed dial number 
simply by lifting the handset. You do not have to dial any digits.
Operation
To immediately connect to a pre-assigned extension or speed dial number:
Hardware Requirements
•N/A
Related Programming
• FF5-5: Hot Line
Considerations
•N/A
Intercom Calling
Description
The System provides two methods of intercom calling: 
•Voice Calling: Extension calls are connected immediately, without a ringing tone.
•Tone Calling: A ringing tone is sent to the called extension.
Extension Class of Service (COS) programming determines whether the default for the originating 
extension is voice or tone calling. Regardless of the default, you can toggle between voice or tone 
calling by entering the Tone-Voice Call feature code. For example, if the extension default is tone 
calling, you can make a voice call to another extension by entering the Tone-Voice Call feature access 
code.Action Result
1.   Lift the handset or press the ON/OFF key. Automatically connected to pre-assigned 
extension or speed dial number 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 6-33
Operation
To make a call using Intercom Calling:
Hardware Requirements
•N/A
Related Programming
• FF1-0-03: Extension COS (Intercom Calling Type)
• FF1-0-03: Extension COS (Voice Call Send)
• FF1-0-03: Extension COS (Voice Call Receive)
• FF3: Extension COS
Considerations
• Both the called and calling parties must belong to an Extension COS that allows Voice Calling.
• You cannot change from voice call to tone call.
Last Number Redial
Description
Last Number Redial allows you to automatically redial the last number dialed by pressing the 
REDIAL key.Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Dial the extension number.
3.   If your extension is set for tone calling and you want to 
make a voice call, enter 1.
Or, if your extension is set for voice call and you want to 
make a tone call, enter 1.
4.   Speak when your call is answered
5.   Replace the handset or press the ON/OFF key. 
						

							6-34 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Operation
To automatically redial the last number dialed:
Hardware Requirements
•N/A
Related Programming
• FF1-0-03: Extension COS (Intercom Redialing)
• FF3: Extension COS
Considerations
• Extension Class of Service (COS) determines whether Last Number Redial can be used for both 
intercom and CO calls, or CO calls only.
Message Waiting/Callback
Description
If you try to call an extension that is busy or does not answer, you can leave a message wait indication 
at that extension, requesting a return call.
Operation
To leave a message waiting indication:Action Result
1.   Lift the handset or press the ON/OFF key.
OR...
Enter a trunk access code.Outside dial tone (if trunk access code 
entered)
2.   Press the REDIAL key.
3.   Complete the call and replace the handset or press the ON/
OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Dial the extension number. Ring or busy tone
3.   While the telephone is still ringing, or when you hear the 
busy tone, enter the Message Wait Set code (default = 4).
4.   Replace the handset or press the ON/OFF key.Message lamp flashes at called extension 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 6-35
To answer a message waiting indication (callback):
To cancel a Callback Message:
Hardware Requirements
•N/A
Related Programming
• FF1-0-03: Extension COS (Message Wait set/Cancel)
• FF1-0-03: Extension COS (Priority Message Wait set/Cancel)
• FF1-2: Dial Plan
• FF3: Extension COS
Considerations
• The System has priority message waiting for 3rd-party Voice Mail. See “Third-Party Voice Mail 
Support” on page 3-59.
Offhook Signaling
Description
Offhook Signaling sends a tone to a busy extension to indicate that another CO call has arrived or a 
call is camped on.Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Message Wait Callback code (default = *6). •   Telephone automatically dials exten-
sion that sent message waiting indica-
tion
•   Message lamp goes off when your call 
is answered
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Callback Request Cancel code (default = *5).
3.   Replace the handset or press the ON/OFF key.Message lamp goes off 
						

							6-36 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Operation
After receiving an offhook signal during a call:
Note:For details about handling multiple calls, see “Call Hold” on page 6-15.
Hardware Requirements
•N/A
Related Programming
• FF3: CO Off-Hook Signal.
Considerations
• The CO call type may be either multiple ring, direct, or camp-on.
• The system does not send the offhook signal under the following conditions:
•   During a conference call
•   During an OHVA or Busy override
•   Data Privacy is enabled
•   the receiving telephone is a 3rd party voice mail.
Offhook Voice Announce
Description
You can interrupt a busy extension when making an Intercom Call, and then use the Off-Hook Voice 
Announce (OHVA) feature to make an announcement that only the called party can hear. You can also 
transfer a held call to a busy extension after making the announcement using this feature. 
To make an OHVA:Action Result
1.   Press the HOLD key.
2.   Press the flashing FF key for the CO line of the incoming 
call.
Action Result
1.   Lift the handset or press the ON/OFF key.
2.   Dial the extension number. Busy signal
3.   Enter the OHVA feature access code (default = 8).
4.   Make your announcement 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 6-37
To transfer a call using OHVA:
Hardware Requirements
•N/A
Related Programming
• FF1 0 03 (System): Extension COS OHVA Originate
• FF1 0 03 (System): Extension COS OHVA Receive
• FF3 (Extension): Extension COS Assignments
• FF4: FF Key Assignments
Considerations
• If Onhook Transfer is enabled, the held call is transferred as soon as the extension sending the 
OHVA hangs up.
• If the transferred call is not answered immediately, it will queue for a set time limit, then return to 
the extension sending the OHVA by Transfer Recall Timer.
• You cannot receive a Call Waiting message during an OHVA. 
• If you make an OHVA to an SLT, the SLT user and the other party will hear the announcement.
Onhook Dialing
Description
Onhook Dialing allows users to dial without lifting the handset. However, the Digital Single Line 
Telephone (DSLT) does not have a microphone so you must lift the handset to talk.
Operation
To use onhook dialing:Action Result
1.   While on a call, press the HOLD key. Current call on hold
2.   Dial the extension number to which the call is being trans-
ferred.Busy signal
3.   Enter OHVA feature access code (default = 8) and announce 
the call to be transferred.
4.   If transfer is: not accepted, press the FLASH key. Transfer canceled
5.   Replace the handset.
Action Result
1.   Press the ON/OFF key. Intercom dial tone
2.   Enter a trunk access code, or dial an extension number. 
						

							6-38 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Hardware Requirements
•N/A
Related Programming
•N/A
Considerations
•N/A
Paging
Description
The System allows you to make both internal and external pages and announcements. Internal pages 
are made via the System’s key telephone speakers. External pages are made through the speakers of 
an external paging system connected to the System.
Paging calls can be answered from any extension using the Meet-Me Answer feature.
Operation
To make a page:
Meet-Me Answer
To answer a page using Meet-Me Answer:
3.   If you entered a trunk access code in step 2, dial the phone 
number. Otherwise, proceed to step 4.
4.   When the call is answered, lift the handset to talk.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Group Paging code (default = #).
3.   Enter the number of the desired paging group (0-9).
4.   Make your announcement.
5.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Meet Me Answer code (default = ##). Connected to specified party
Action Result