Panasonic Kx Taw848 PC Cprogramming Manual

							2.8 [2] System
PC Programming Manual 111
DISA—CO-to-CO Call Prolong Counter
Specifies the number of times that the caller can prolong a CO-to-CO line call on a DISA line. 
(Selecting 0 enables the caller to prolong the CO-to-CO line call without restriction.)
Default
10
Value Range
0–15
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.4 [5-3-2] Voice Message—DISA Message
Feature Manual References
1.4.6 DISA (Direct Inward System Access)
DISA—CO-to-CO Call Prolong Time
Specifies the length of time that a CO-to-CO line call on a DISA line is prolonged each time that the 
caller prolongs the call. (Selecting 0 prevents the caller from prolonging the CO-to-CO line call.)
Default
3 min
Value Range
0–7 min
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.4 [5-3-2] Voice Message—DISA Message
Feature Manual References
1.4.6 DISA (Direct Inward System Access)
DISA—Progress Tone Continuation Time before Recording Message
Specifies the length of time that a progress tone is sent to the manager extension before recording 
an OGM.
Default
5 s 
						

							2.8 [2] System
112 PC Programming Manual
Value Range
0–7 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.4 [5-3-2] Voice Message—DISA Message
Feature Manual References
1.12.1 OGM (Outgoing Message)
DISA—Reorder Tone Duration
Specifies the length of time that a reorder tone is sent to the caller before the call is disconnected.
Default
10 s
Value Range
1–15 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.4 [5-3-2] Voice Message—DISA Message
Feature Manual References
1.4.6 DISA (Direct Inward System Access)
Doorphone—Call Ring Duration
Specifies the length of time that a call from a doorphone rings until the call is cancelled when there 
is no answer.
Default
30 s
Value Range
10 × n (n=1–15) s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.1 [5-1] Doorphone 
						

							2.8 [2] System
PC Programming Manual 113
Feature Manual References
1.4.10 Doorphone Call
Doorphone—Call Duration
Specifies the length of time until an answered doorphone call is disconnected.
Default
60 s
Value Range
10 × n (n=0–30) s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.1 [5-1] Doorphone
Feature Manual References
1.4.10 Doorphone Call
Doorphone—Open Duration
Specifies the length of time that a door stays unlocked after being opened from an extension.
Default
5 s
Value Range
2–7 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.11.1 [5-1] Doorphone
Feature Manual References
1.4.9 Door Open
Timed Reminder—Repeat Counter
Specifies the number of times that an alarm is repeated.
Default
3 
						

							2.8 [2] System
114 PC Programming Manual
Value Range
1–15
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.17.3 Timed Reminder
Timed Reminder—Interval Time
Specifies the length of time between the repeated alarms.
Default
30 s
Value Range
10 × n (n=1–120) s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.17.3 Timed Reminder
Timed Reminder—Alarm Ringing Duration
Specifies the length of time that an alarm rings.
Default
30 s
Value Range
10 × n (n=1–30) s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None 
						

							2.8 [2] System
PC Programming Manual 115
Feature Manual References
1.17.3 Timed Reminder
Unattended Conference—Recall Start Timer
Specifies the length of time until the conference originator receives an Unattended Conference Recall 
tone.
Default
10 min
Value Range
0–60 min
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.3.13 Conference
Unattended Conference—Warning Tone Start Timer
Specifies the length of time until the parties involved in an Unattended Conference receive a warning 
tone after the conference originator receives the Unattended Conference Recall tone but does not 
return to the conference.
Default
30 s
Value Range
0–240 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.3.13 Conference 
						

							2.8 [2] System
116 PC Programming Manual
Unattended Conference—Disconnect Timer
Specifies the length of time until an Unattended Conference is disconnected after the parties involved 
in the conference receive a warning tone but the conference originator does not return to the 
conference.
Default
15 s
Value Range
0–240 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.3.13 Conference
Miscellaneous
Caller ID—Waiting to receive
Specifies the length of time that the PBX waits to receive Caller ID from an analog CO line. If the 
Caller ID is received through an analog CO line card on which no Caller ID card is mounted or through 
a port to which Caller ID Detection is disabled, this timer is not applicable.
Default
5 s
Value Range
0–15 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.12.1 [6-1] System Speed Dial
2.12.2 [6-2] Caller ID Modification
Feature Manual References
1.3.1 Caller ID 
						

							2.8 [2] System
PC Programming Manual 117
Caller ID—Visual Caller ID Display
Specifies the length of time that a Caller ID number, with the Call Waiting tone offered by an analog 
line from the telephone company, is shown on the display. The Caller ID number flashes on the display 
for five seconds, followed by a 10-second pause, then flashes again for five seconds.
Default
30 s
Value Range
0–250 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
1.3.9 Call Waiting Tone
Extension PIN—Lock Counter
Specifies the number of successive incorrect PIN entries allowed before the extension PIN is locked. 
A locked extension PIN can not be used until reset from the extension assigned as manager. 
(Specifying None disables this counter.)
Default
None
Value Range
None, 1–15
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.5.6 Extension PIN (Personal Identification Number)
1.19.1 Verification Code Entry
1.20.1 Walking COS
External Sensor—Ring Duration
Specifies the length of time that the PBX waits for the called party to answer before cancelling a 
sensor call. 
						

							2.8 [2] System
118 PC Programming Manual
Default
30 s
Value Range
10 × n (n=1–15) s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.5.9 External Sensor
PT Display—PT Last Display Duration in Idle Mode
Specifies the length of time that the current information remains on the display after the extension 
returns to idle status.
Default
5 s
Value Range
1–15 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
None
Voice Mail (Caller from VM to CO)—On-hook Wait Time
Specifies the length of time from when the VPS seizes a CO line (for example, to transfer a call) until 
the VPS goes on hook. If the time specified here is too short, the VPS will be unable to dial the 
number and make a connection.
Default
10 s
Value Range
1–30 s 
						

							2.8 [2] System
PC Programming Manual 119
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.19.3 Voice Mail (VM) Group
During Conversation—DTMF Signal Length
Specifies the length of time that a DTMF signal is sent when a number is dialed from a PT or PS 
during a conversation.
Default
160 ms
Value Range
80 ms, 160 ms, 240 ms, 320 ms
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
None
During Conversation—DTMF Inter-digit Pause
Specifies the length of time between DTMF signals when numbers are dialed in succession from a 
PT or PS during a conversation.
Default
112 ms
Value Range
64 + 16 × n (n=0–15) ms
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
None 
						

							2.8 [2] System
120 PC Programming Manual
During Conversation—Pause Signal Time
Specifies the length of the pause inserted when the PAUSE button is pressed during a conversation.
Default
1.5 s
Value Range
1.5 s, 2.5 s, 3.5 s, 4.5 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
1.13.4 Pause Insertion
System Wireless—PS Out of Range Timer *) If 0 is set, timer is controlled 
by cell station.
When the destination of an incoming call is a PS, specifies the length of time the PBX searches for 
the PS before setting its status to Out of Range.
 
If 0 is assigned, the timer is controlled by the cell station.
Default
0 s
Value Range
0 s, 4 s, 8 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
None
Feature Manual References
None
SVM—Recording Time
Specifies the maximum length of a message recorded by the SVM feature.
Default
120 s