Panasonic Kx Taw848 PC Cprogramming Manual

							2.7 [1] Configuration
PC Programming Manual 61
2.7.2 [1-1] Slot—Summary
Summary information is displayed for all cards installed in the PBX.
Slot
Indicates the slot number (reference only).
Default
Current slot number
Value Range
Available slot numbers.
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Programming Manual References
None
Feature Manual References
None
Slot Type
Indicates the type of each slot (reference only).
Default
Not applicable.
Value Range
Fixed Slot: For initially installed 4 Hybrid ports
Free Slot Type A (02–04): For LCOT4/HLC4/PLC4 card
Free Slot Type B (05–06): For PLC8/SLC8 card
Option Slot (08–09): For MSG2/DPH4/ECHO8/EXT-CID/SVM2 card
Option Slot (10–11): For MSG2/ECHO8/EXT-CID/SVM2 card
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Installation Manual References
2.2.6 Installing/Removing the Optional Service Cards
Programming Manual References
None 
						

							2.7 [1] Configuration
62 PC Programming Manual
Feature Manual References
None
Card Type
Indicates the type of service card installed in each slot of the PBX (reference only). 
Note that for MPR cards, the PBX model code is displayed in parentheses after the name.
Default
Slot 00: MPR (Main Processing Card: fixed)
Other slots: Not stored.
Value Range
HLC4: 4-Port Hybrid Extension Card
PLC4: 4-Port Proprietary Extension Card
PLC8: 8-Port Proprietary Extension Card
SLC8: 8-Port Single Line Telephone Extension Card
LCOT4: 4-Port Analog CO Line Card
MSG2: 2-Channel Message Card
DPH4: 4-Port Doorphone Card
ECHO8: 8-Channel Echo Canceller Card
EXT-CID: Extension Caller ID Card
SVM2: Simplified Voice Message Card
MPR: MPR Card
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Programming Manual References
2.7.1 [1-1] Slot
2.7.3 [1-1] Slot—Extension Card Property
2.7.7 [1-1] Slot—LCO Card Property
2.7.10 [1-1] Slot—DPH Card Property
Feature Manual References
None
Status
Indicates the card status (reference only). 
Note that MPR card status is always displayed as -.
Default
Slot 00: - (fixed)
Other slots: Current status 
						

							2.7 [1] Configuration
PC Programming Manual 63
Value Range
INS: The port is in service.
OUS: The por t is out of service.
Fault: The port is not communicating with the network.
Pre-Install: A card has been added to the slot in batch programming mode.
Idle: No card is installed in the slot..
Maintenance Console Location
2.7.2 [1-1] Slot—Summary
Programming Manual References
2.7.1 [1-1] Slot
Feature Manual References
None
2.7.3 [1-1] Slot—Extension Card Property
The property for the extension cards can be specified.
SLT Pulse Dial Mode
Selects the type of pulse dial transmission appropriate to your area.
Default
Normal 
Value Range
Normal, Sweden, New Zealand
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Off Hook Time
Specifies the minimum length that a pulse dial sent from an SLT must be for the PBX to recognize it 
as an off-hook signal.
Default
160 ms 
						

							2.7 [1] Configuration
64 PC Programming Manual
Value Range
8 × n (n=3–255) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Off Hook Guard Time
Specifies the length of guard time used for off-hook signals from SLTs, to prevent the PBX mistaking 
them for pulse dials.
Default
504 ms
Value Range
8 × n (n=12–63) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Pulse Maximum Break Width
Specifies the maximum length of the break signal in a pulse dial.
Default
96 ms
Value Range
8 × n (n=9–20) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None 
						

							2.7 [1] Configuration
PC Programming Manual 65
Feature Manual References
None
SLT Pulse Minimum Make Width
Specifies the minimum length of the make signal in a pulse dial.
Default
8 ms
Value Range
8 × n (n=1–5) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
SLT Flash Detection
Enables the PBX to detect the flash signal sent when an SLT user presses the hookswitch or the 
Flash/Recall button.
Default
Enable
Value Range
Disable: The PBX disconnects the line to prevent placing the call on hold.
Enable: The PBX places the call on consultation hold.
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
1.3.7 Call Splitting
Flash Timing - Min.
Specifies the minimum length that a signal sent from an SLT must be for the PBX to recognize it as 
a hookswitch flash signal. 
						

							2.7 [1] Configuration
66 PC Programming Manual
Default
112 ms
Value Range
8 × n (n=3–63) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
Flash Timing - Range
Specifies the maximum length that a signal sent from an SLT can be for the PBX to recognize it as a 
hookswitch flash signal.
Default
904 ms
Value Range
8 × n (n=3–191) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property
Programming Manual References
None
Feature Manual References
None
DTMF-R STD Detection Time
Specifies the minimum length that a DTMF tone must be for the PBX to recognize it as a DTMF tone.
Default
30 ms
Value Range
2 × n (n=1–31) ms
Maintenance Console Location
2.7.3 [1-1] Slot—Extension Card Property 
						

							2.7 [1] Configuration
PC Programming Manual 67
Programming Manual References
None
Feature Manual References
None
2.7.4 [1-1] Slot—Extension Port
Various settings can be programmed for each extension port. 
To change the status of extension ports, click Command. To view total numbers of each type of 
extension connected, click Por t Type View.
Slot
Indicates the slot position (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the por t number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None 
						

							2.7 [1] Configuration
68 PC Programming Manual
Feature Manual References
1.5.7 Extension Port Configuration
Por t Type
Indicates the port type (reference only).
Default
Current port type
Value Range
APT: APT port (PLC) 
SLT: SLT port (SLC) 
Hybrid: Hybrid port (HLC)
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None
Feature Manual References
1.5.7 Extension Port Configuration
Telephone Type
Indicates the connected telephone type (reference only). 
The number of all connected telephones and Cell Stations can be viewed by clicking Por t Type View.
Default
Current connected telephone type
Value Range
APT: APT is connected. 
DSS: DSS Console is connected. 
VPS: VPS is connected. 
SLT: SLT is connected (or no telephone is connected to the Hybrid or SLT port). 
CS: CS is connected. 
No Connection: No telephone is connected.
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
2.7.6 [1-1] Slot—Extension Port—Port Type View
Feature Manual References
1.5.7 Extension Port Configuration 
						

							2.7 [1] Configuration
PC Programming Manual 69
Connection
Indicates the por t status (reference only). 
This column offers two ways to open the screen to select the por t command as follows:
 Click the desired cell in the column.
 Select the desired cell in the column, and then click Command.
Default
Current status
Value Range
INS: The port is in service.
OUS: The por t is out of service.
Fault: The port is not communicating with the PBX.
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None
Extension Number
Specifies the extension number of the port.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the por t is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101
Value Range
Max. 4 digits (consisting of 0–9)
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command 
						

							2.7 [1] Configuration
70 PC Programming Manual
Feature Manual References
None
Extension Name
Specifies the extension name of the port.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
None
Feature Manual References
None
DPT Type—Type (for Hybrid port)
Selects the port type.
To change the port type of an extension port, follow the steps below:
1.Set the status of the extension port to OUS.
2.Change the port type of the extension port, then click Apply.
3.Set the status of the extension port to INS.
When changing the port type of an extension port for which Wireless XDP has been set on the 
2.10.1 [4-1-1] Wired Extension—Extension Settings screen, the Wireless XDP setting must 
be deleted first.
Default
Normal
Value Range
Normal: For connecting a PT 
DSS: For connecting a DSS Console (A maximum of 4 DSS Consoles can be connected to the PBX.) 
VM (DPT): For connecting a Panasonic VPS through DPT Integration
Maintenance Console Location
2.7.4 [1-1] Slot—Extension Port
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command