Panasonic Kx Taw848 PC Cprogramming Manual

							2.8 [2] System
PC Programming Manual 161
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.5.3 Executive Busy Override
DND Override
Enables making a call to an extension in DND mode by entering the feature number.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.2 [4-1-2] Wired Extension—FWD/DND
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
2.10.9 [4-2-2] Portable Station—FWD / DND
Feature Manual References
1.4.8 DND (Do Not Disturb)
Call Monitor
Enables listening to a busy extensions conversation.
Default
Disable
Value Range
Disable, Enable 
						

							2.8 [2] System
162 PC Programming Manual
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.3.4 Call Monitor
Programming & Manager
COS Name
Specifies the name of the COS.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
None
Feature Manual References
1.3.16 COS (Class of Service)
Executive Busy Override Deny
Enables preventing other extensions from interrupting calls.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS 
						

							2.8 [2] System
PC Programming Manual 163
Feature Manual References
1.3.16 COS (Class of Service)
Group Forward Set
Enables setting call forwarding for calls to an incoming call distribution group.
Default
Enable-Group
Value Range
Disable: An extension cannot set call forwarding for any group. 
Enable-All: An extension can set call forwarding for all groups. 
Enable-Group: An extension can only set call forwarding for the group to which the extension belongs.
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.9.11 [3-5-4] Incoming Call Distribution Group—Member
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.6.6 FWD (Call Forwarding)
Programming Mode Level
Specifies the level of authorization for performing PT programming.
Default
PROG Only
Value Range
Disable: A PT user cannot perform any programming. 
PROG Only: A PT user can perform only personal programming. 
PROG and PROG **/*#: A PT user can perform both personal and system programming.
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.13.15 PT Programming 
						

							2.8 [2] System
164 PC Programming Manual
Manager
Specifies the authorization to use manager features.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.11.1 Manager Features
Time Service Switch
Enables manual switching of time modes.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.8.5 [2-4] Week Table
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.17.4 Time Service
Optional Device & Other Extension
COS Name
Specifies the name of the COS. 
						

							2.8 [2] System
PC Programming Manual 165
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
None
Feature Manual References
1.3.16 COS (Class of Service)
Door Unlock
Enables using the door opener feature.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.4.9 Door Open
External Relay Access
Enables access to external relays.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings 
						

							2.8 [2] System
166 PC Programming Manual
Programming Manual References
2.11.6 [5-4] External Relay
Feature Manual References
1.5.8 External Relay
Accept the Call from DISA
Enables reception of calls from DISA.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
2.11.4 [5-3-2] Voice Message—DISA Message
Feature Manual References
1.4.6 DISA (Direct Inward System Access)
Remote Operation by Other Extension
 Allows the Walking COS feature to be used from a remote location (inside the PBX, or outside the 
PBX using DISA).
Default
Allow
Value Range
Allow, Deny
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
Feature Manual References
1.20.1 Walking COS 
						

							2.8 [2] System
PC Programming Manual 167
Accept Wireless XDP Parallel Set by PS
Allows Wireless XDP Parallel Mode to be set by a PS.
Default
Allow
Value Range
Allow, Deny
Maintenance Console Location
2.8.11 [2-7-1] Class of Service—COS Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
Feature Manual References
1.20.3 Wireless XDP Parallel Mode
2.8.12 [2-7-2] Class of Service—External Call Block
Each COS can have different trunk groups available for making CO line calls, depending on the time 
mode (day/lunch/break/night). Select the desired time mode from the list.
Outgoing Trunk Group 1–64
Specifies the available trunk groups.
Default
All Trunk groups: Non Block
Value Range
Block (blue), Non Block
Maintenance Console Location
2.8.12 [2-7-2] Class of Service—External Call Block
Programming Manual References
2.8.5 [2-4] Week Table
2.10.1 [4-1-1] Wired Extension—Extension Settings
2.10.8 [4-2-1] Portable Station—Extension Settings
2.15.1 [9-1] CO Line Settings
Feature Manual References
1.3.11 CO Line Access 
						

							2.8 [2] System
168 PC Programming Manual
2.8.13 [2-7-3] Class of Service—Internal Call Block
Internal Call Block determines the restrictions placed on making intercom calls. The extensions, 
incoming call distribution groups, and doorphones belonging to a certain COS can be programmed 
to not receive intercom calls from those belonging to a certain COS.
COS Number of the Extension Which Receive the Call from Other Extension 
1–64
Specifies the combinations of COS levels for which intercom calls are blocked.
Default
All extensions: Non Block
Value Range
Block (blue), Non Block
Maintenance Console Location
2.8.13 [2-7-3] Class of Service—Internal Call Block
Programming Manual References
2.9.9 [3-5-1] Incoming Call Distribution Group—Group Settings—Main—COS
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—COS
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—COS
2.11.1 [5-1] Doorphone—COS
Feature Manual References
1.9.12 Internal Call Block
2.8.14 [2-8-1] Ring Tone Patterns—Call from CO
Different ring tone patterns can be selected for incoming CO line calls depending on the trunk group 
that the calls are received on. A maximum of 8 Ring Tone Pattern Tables can be programmed, and 
any pattern table can be selected for use by an extension.
Ring Tone Pattern Plan 1–8
Specifies the ring tone pattern for incoming CO line calls.
Default
Single
Value Range
Single, Double, Triple
Maintenance Console Location
2.8.14 [2-8-1] Ring Tone Patterns—Call from CO 
						

							2.8 [2] System
PC Programming Manual 169
Programming Manual References
2.15.1 [9-1] CO Line Settings—Trunk Group Number
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—Ring Pattern Table
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—Ring Pattern Table
Feature Manual References
1.15.2 Ring Tone Pattern Selection
2.8.15 [2-8-2] Ring Tone Patterns—Call from Doorphone
Different ring tone patterns can be selected for incoming doorphone calls depending on the 
doorphone port that the calls originate from. A maximum of 8 Ring Tone Pattern Tables can be 
programmed, and any pattern table can be selected for use by an extension.
Ring Tone Pattern Plan 1–8
Specifies the ring tone pattern for incoming doorphone calls.
Default
Triple
Value Range
Single, Double, Triple, S-Double
Maintenance Console Location
2.8.15 [2-8-2] Ring Tone Patterns—Call from Doorphone
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—Ring Pattern Table
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—Ring Pattern Table
2.11.1 [5-1] Doorphone
Feature Manual References
1.4.10 Doorphone Call
1.15.2 Ring Tone Pattern Selection
2.8.16 [2-8-3] Ring Tone Patterns—Call from Others
Different ring tone patterns can be selected for incoming intercom calls and ringing triggered by 
certain PBX features (Timed Reminder, Call Back, and Live Call Screening). A maximum of 8 Ring 
Tone Pattern Tables can be programmed, and any pattern table can be selected for use by an 
extension. 
For more information on ring tone patterns, see 1.15.2 Ring Tone Pattern Selection in the Feature 
Manual. 
						

							2.8 [2] System
170 PC Programming Manual
Extension—Ring Tone Pattern Plan 1–8
Specifies the ring tone pattern for incoming intercom calls.
Default
Double
Value Range
Single, Double, Triple
Maintenance Console Location
2.8.16 [2-8-3] Ring Tone Patterns—Call from Others
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—Ring Pattern Table
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—Ring Pattern Table
Feature Manual References
None
Timed Reminder—Ring Tone Pattern Plan 1–8
Specifies the ring tone pattern for Timed Reminder alarms.
Default
Triple
Value Range
Single, Double, Triple
Maintenance Console Location
2.8.16 [2-8-3] Ring Tone Patterns—Call from Others
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Main—Ring Pattern Table
2.10.8 [4-2-1] Portable Station—Extension Settings—Main—Ring Pattern Table
Feature Manual References
1.17.3 Timed Reminder
Call Back—Ring Tone Pattern Plan 1–8
Specifies the ring tone pattern for callback ringing by Automatic Callback Busy.
Default
S-Double