Panasonic Kx Taw848 PC Cprogramming Manual
Have a look at the manual Panasonic Kx Taw848 PC Cprogramming Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 10737 Panasonic manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 186
2.8 [2] System
186 PC Programming Manual
DSS Key—Call Pick-up by DSS key for Direct Incoming Call
Specifies whether a DSS button will light up or flash when a call rings at the specified extension. To
enable this setting,
DSS Key—DSS Key mode for Incoming Call on this screen must be set to ON
or Flash.
Default
Enable
Value Range
Disable: The DSS button will light up when a call arrives, but pressing it will not pick up the call.
Enable: The DSS button will flash when a call arrives, and pressing it...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-185.png "Page 186
2.8 [2] System
186 PC Programming Manual
DSS Key—Call Pick-up by DSS key for Direct Incoming Call
Specifies whether a DSS button will light up or flash when a call rings at the specified extension. To
enable this setting,
DSS Key—DSS Key mode for Incoming Call on this screen must be set to ON
or Flash.
Default
Enable
Value Range
Disable: The DSS button will light up when a call arrives, but pressing it will not pick up the call.
Enable: The DSS button will flash when a call arrives, and pressing it...")
![Page 187
2.8 [2] System
PC Programming Manual 187
Default
Disable
Value Range
Disable: The PBX disconnects the current call, and calls the extension assigned to the DSS button.
Enable: The PBX places the current call on consultation hold.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.8 Call Transfer
Transfer—Transfer to Busy Extension without BSS Operation
Enables a transferred call to be queued when the transfer destination is busy....](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-186.png "Page 187
2.8 [2] System
PC Programming Manual 187
Default
Disable
Value Range
Disable: The PBX disconnects the current call, and calls the extension assigned to the DSS button.
Enable: The PBX places the current call on consultation hold.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.8 Call Transfer
Transfer—Transfer to Busy Extension without BSS Operation
Enables a transferred call to be queued when the transfer destination is busy....")
![Page 188
2.8 [2] System
188 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.8.1 Hands-free Answerback
Option 5
SLT—SLT Hold Mode
Selects how to hold a line and transfer a call with an SLT. For details of each mode, see 1.3.2 Call
Hold in the Feature Manual.
Default
Mode 2
Value Range
Mode 1, Mode 2, Mode 3, Mode 4
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-187.png "Page 188
2.8 [2] System
188 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.8.1 Hands-free Answerback
Option 5
SLT—SLT Hold Mode
Selects how to hold a line and transfer a call with an SLT. For details of each mode, see 1.3.2 Call
Hold in the Feature Manual.
Default
Mode 2
Value Range
Mode 1, Mode 2, Mode 3, Mode 4
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual...")
![Page 189
2.8 [2] System
PC Programming Manual 189
Value Range
Disable: No port
Slot 01:HLC4: Initially installed 4 Hybrid ports
Slot nn:SLC8 1-4: Ports 1 to 4 of the SLC8 card (nn=slot number)
Slot nn:SLC8 5-8: Ports 5 to 8 of the SLC8 card (nn=slot number)
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Option 7—Extension Caller ID Sending
Feature Manual References
1.3.1 Caller ID
Extension Caller ID Modulation...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-188.png "Page 189
2.8 [2] System
PC Programming Manual 189
Value Range
Disable: No port
Slot 01:HLC4: Initially installed 4 Hybrid ports
Slot nn:SLC8 1-4: Ports 1 to 4 of the SLC8 card (nn=slot number)
Slot nn:SLC8 5-8: Ports 5 to 8 of the SLC8 card (nn=slot number)
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Option 7—Extension Caller ID Sending
Feature Manual References
1.3.1 Caller ID
Extension Caller ID Modulation...")
![Page 190
2.8 [2] System
190 PC Programming Manual
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Mark Signal bits
Specifies the number of mark bits to send when sending Caller ID information to an SLT.
Default
180 bits
Value Range
10 × n (n=3–40) bits
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Channel Seizure Wait Time
Specifies the length of time that the PBX waits before starting to...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-189.png "Page 190
2.8 [2] System
190 PC Programming Manual
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Mark Signal bits
Specifies the number of mark bits to send when sending Caller ID information to an SLT.
Default
180 bits
Value Range
10 × n (n=3–40) bits
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Channel Seizure Wait Time
Specifies the length of time that the PBX waits before starting to...")
![Page 191
2.8 [2] System
PC Programming Manual 191
Additional Local Trunk Access Code to Extension Caller ID
Enables the PBX to automatically add a CO Line Access number to the received telephone number
when sending the Caller ID number of an incoming CO line call to an SLT.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Send Caller ID Date & Time to Extension
Enables the PBX...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-190.png "Page 191
2.8 [2] System
PC Programming Manual 191
Additional Local Trunk Access Code to Extension Caller ID
Enables the PBX to automatically add a CO Line Access number to the received telephone number
when sending the Caller ID number of an incoming CO line call to an SLT.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Send Caller ID Date & Time to Extension
Enables the PBX...")
![Page 192
2.8 [2] System
192 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Send Caller ID Long Distance to Extension
Enables the PBX to send a call qualifier (Long Distance) (if received from the CO line) when sending
Caller ID information to an SLT.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-191.png "Page 192
2.8 [2] System
192 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Send Caller ID Long Distance to Extension
Enables the PBX to send a call qualifier (Long Distance) (if received from the CO line) when sending
Caller ID information to an SLT.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming...")
![Page 193
2.8 [2] System
PC Programming Manual 193
Maintenance Console Location
2.8.19 [2-11-1] Audio Gain—Paging/MOH
Programming Manual References
2.9.6 [3-4] Paging Group
Feature Manual References
1.13.1 Paging
MOH—(Music On Hold)
Specifies the music volume for the External BGM.
Default
9 dB
Value Range
-11–11 dB
Maintenance Console Location
2.8.19 [2-11-1] Audio Gain—Paging/MOH
Programming Manual References
2.8.3 [2-2] Operator & BGM
Feature Manual References
1.2.1 BGM (Background Music)
1.11.4 Music on Hold](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-192.png "Page 193
2.8 [2] System
PC Programming Manual 193
Maintenance Console Location
2.8.19 [2-11-1] Audio Gain—Paging/MOH
Programming Manual References
2.9.6 [3-4] Paging Group
Feature Manual References
1.13.1 Paging
MOH—(Music On Hold)
Specifies the music volume for the External BGM.
Default
9 dB
Value Range
-11–11 dB
Maintenance Console Location
2.8.19 [2-11-1] Audio Gain—Paging/MOH
Programming Manual References
2.8.3 [2-2] Operator & BGM
Feature Manual References
1.2.1 BGM (Background Music)
1.11.4 Music on Hold")
![Page 194
2.9 [3] Group
194 PC Programming Manual
2.9 [3] Group
2.9.1 [3-1-1] Trunk Group—TRG Settings
CO lines can be organized into trunk groups. The settings of each trunk group determine the settings
of the CO lines within that group. A maximum of 64 trunk groups can be programmed.
For more information on trunk groups, see 1.7.1 GROUP FEATURES in the Feature Manual.
Main
Group Name
Specifies the name of the trunk group for programming reference.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-193.png "Page 194
2.9 [3] Group
194 PC Programming Manual
2.9 [3] Group
2.9.1 [3-1-1] Trunk Group—TRG Settings
CO lines can be organized into trunk groups. The settings of each trunk group determine the settings
of the CO lines within that group. A maximum of 64 trunk groups can be programmed.
For more information on trunk groups, see 1.7.1 GROUP FEATURES in the Feature Manual.
Main
Group Name
Specifies the name of the trunk group for programming reference.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance...")
![Page 195
2.9 [3] Group
PC Programming Manual 195
2.15.1 [9-1] CO Line Settings
Feature Manual References
None
Line Hunting Order
Specifies the CO line hunting sequence for the trunk group. The hunting sequence can be
programmed to start from the lowest or highest numbered CO lines, or to rotate uniformly among all
CO lines.
Default
High -> Low
Value Range
High -> Low, Low -> High, Rotation
Maintenance Console Location
2.9.1 [3-1-1] Trunk Group—TRG Settings
Programming Manual References
2.15.1 [9-1] CO Line...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-194.png "Page 195
2.9 [3] Group
PC Programming Manual 195
2.15.1 [9-1] CO Line Settings
Feature Manual References
None
Line Hunting Order
Specifies the CO line hunting sequence for the trunk group. The hunting sequence can be
programmed to start from the lowest or highest numbered CO lines, or to rotate uniformly among all
CO lines.
Default
High -> Low
Value Range
High -> Low, Low -> High, Rotation
Maintenance Console Location
2.9.1 [3-1-1] Trunk Group—TRG Settings
Programming Manual References
2.15.1 [9-1] CO Line...")
![Page 196
2.9 [3] Group
196 PC Programming Manual
Extension-CO Duration Time
Specifies the length of time that an extension-to-CO line call can be maintained before being
disconnected.
Default
10 min
Value Range
None, 1–60 min
Maintenance Console Location
2.9.1 [3-1-1] Trunk Group—TRG Settings
Programming Manual References
2.8.11 [2-7-1] Class of Service—COS Settings
2.8.17 [2-9] System Options
2.15.1 [9-1] CO Line Settings
Feature Manual References
1.3.12 CO Line Call Limitation
Caller-ID Modification Table...](http://img.usermanuals.tech/thumb/58/64586/w64_kx-taw848_en_adv_pcprog_v3_om_d-195.png "Page 196
2.9 [3] Group
196 PC Programming Manual
Extension-CO Duration Time
Specifies the length of time that an extension-to-CO line call can be maintained before being
disconnected.
Default
10 min
Value Range
None, 1–60 min
Maintenance Console Location
2.9.1 [3-1-1] Trunk Group—TRG Settings
Programming Manual References
2.8.11 [2-7-1] Class of Service—COS Settings
2.8.17 [2-9] System Options
2.15.1 [9-1] CO Line Settings
Feature Manual References
1.3.12 CO Line Call Limitation
Caller-ID Modification Table...")
2.8 [2] System PC Programming Manual 191 Additional Local Trunk Access Code to Extension Caller ID Enables the PBX to automatically add a CO Line Access number to the received telephone number when sending the Caller ID number of an incoming CO line call to an SLT. Default Enable Value Range Disable, Enable Maintenance Console Location 2.8.18 [2-10] Extension CID Settings Programming Manual References None Feature Manual References 1.3.1 Caller ID Send Caller ID Date & Time to Extension Enables the PBX to send the date and time of an incoming call when sending Caller ID information to an SLT. Default Enable Value Range Disable, Enable Maintenance Console Location 2.8.18 [2-10] Extension CID Settings Programming Manual References None Feature Manual References 1.3.1 Caller ID Send Caller ID Name to Extension Enables the PBX to send the callers name when sending Caller ID information to an SLT. Default Enable
2.8 [2] System 192 PC Programming Manual Value Range Disable, Enable Maintenance Console Location 2.8.18 [2-10] Extension CID Settings Programming Manual References None Feature Manual References 1.3.1 Caller ID Send Caller ID Long Distance to Extension Enables the PBX to send a call qualifier (Long Distance) (if received from the CO line) when sending Caller ID information to an SLT. Default Enable Value Range Disable, Enable Maintenance Console Location 2.8.18 [2-10] Extension CID Settings Programming Manual References None Feature Manual References 1.3.1 Caller ID 2.8.19 [2-11-1] Audio Gain—Paging/MOH Gain levels for the External Pager/External BGM ports can be programmed. Paging—EPG (External Pager) Specifies the paging volume for the External Pager. Default -2 dB Value Range -15–15 dB
2.8 [2] System PC Programming Manual 193 Maintenance Console Location 2.8.19 [2-11-1] Audio Gain—Paging/MOH Programming Manual References 2.9.6 [3-4] Paging Group Feature Manual References 1.13.1 Paging MOH—(Music On Hold) Specifies the music volume for the External BGM. Default 9 dB Value Range -11–11 dB Maintenance Console Location 2.8.19 [2-11-1] Audio Gain—Paging/MOH Programming Manual References 2.8.3 [2-2] Operator & BGM Feature Manual References 1.2.1 BGM (Background Music) 1.11.4 Music on Hold
2.9 [3] Group 194 PC Programming Manual 2.9 [3] Group 2.9.1 [3-1-1] Trunk Group—TRG Settings CO lines can be organized into trunk groups. The settings of each trunk group determine the settings of the CO lines within that group. A maximum of 64 trunk groups can be programmed. For more information on trunk groups, see 1.7.1 GROUP FEATURES in the Feature Manual. Main Group Name Specifies the name of the trunk group for programming reference. Default Not stored. Value Range Max. 20 characters Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.15.1 [9-1] CO Line Settings Feature Manual References None COS Specifies the COS of the trunk group. If you wish to prevent such calls from being made, ensure that the COS specified here has a TRS level of 7 assigned for all relevant time modes in 2.8.11 [2-7-1] Class of Service—COS Settings. Default 7 Value Range 1–64 Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.8.11 [2-7-1] Class of Service—COS Settings
2.9 [3] Group PC Programming Manual 195 2.15.1 [9-1] CO Line Settings Feature Manual References None Line Hunting Order Specifies the CO line hunting sequence for the trunk group. The hunting sequence can be programmed to start from the lowest or highest numbered CO lines, or to rotate uniformly among all CO lines. Default High -> Low Value Range High -> Low, Low -> High, Rotation Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.15.1 [9-1] CO Line Settings Feature Manual References 1.3.11 CO Line Access CO-CO Duration Time Specifies the length of time that a CO-to-CO line call line call can be maintained before being disconnected. Default 10 min Value Range None, 1–60 min Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.15.1 [9-1] CO Line Settings Feature Manual References 1.3.12 CO Line Call Limitation
2.9 [3] Group 196 PC Programming Manual Extension-CO Duration Time Specifies the length of time that an extension-to-CO line call can be maintained before being disconnected. Default 10 min Value Range None, 1–60 min Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.8.11 [2-7-1] Class of Service—COS Settings 2.8.17 [2-9] System Options 2.15.1 [9-1] CO Line Settings Feature Manual References 1.3.12 CO Line Call Limitation Caller-ID Modification Table Specifies the table to be used for modifying caller information (telephone number). Default 1 Value Range 1–4 Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.12.2 [6-2] Caller ID Modification 2.15.1 [9-1] CO Line Settings Feature Manual References 1.3.1 Caller ID Tone Detection Group Name Specifies the name of the trunk group for programming reference.
2.9 [3] Group PC Programming Manual 197 Default Not stored. Value Range Max. 20 characters Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.15.1 [9-1] CO Line Settings Feature Manual References None DISA Tone Detection—Silence Enables the disconnection of a DISA-originated CO-to-CO line call line call by silence detection. Default Disable Value Range Disable, Enable Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.11.3 [5-3-1] Voice Message—DISA System 2.15.1 [9-1] CO Line Settings Feature Manual References 1.4.6 DISA (Direct Inward System Access) DISA Tone Detection—Continuous Enables the disconnection of a DISA-originated CO-to-CO line call line call by continuous signal detection. Default Enable Value Range Disable, Enable
2.9 [3] Group 198 PC Programming Manual Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.11.3 [5-3-1] Voice Message—DISA System 2.15.1 [9-1] CO Line Settings Feature Manual References 1.4.6 DISA (Direct Inward System Access) DISA Tone Detection—Cyclic Enables the disconnection of a DISA-originated CO-to-CO line call line call by cyclic signal detection. Default Enable Value Range Disable, Enable Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.11.3 [5-3-1] Voice Message—DISA System 2.15.1 [9-1] CO Line Settings Feature Manual References 1.4.6 DISA (Direct Inward System Access) Simplified Voice Message Tone Detection—Silence Enables the disconnection of an SVM-originated CO-to-CO line call by silence detection. Default Enable Value Range Disable, Enable Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References None
2.9 [3] Group PC Programming Manual 199 Feature Manual References 1.16.5 SVM (Simplified Voice Message) Simplified Voice Message Tone Detection—Continuous Enables the disconnection of an SVM-originated CO-to-CO line call by continuous signal detection. Default Enable Value Range Disable, Enable Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References None Feature Manual References 1.16.5 SVM (Simplified Voice Message) Simplified Voice Message Tone Detection—Cyclic Enables the disconnection of an SVM-originated CO-to-CO line call by cyclic signal detection. Default Enable Value Range Disable, Enable Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References None Feature Manual References 1.16.5 SVM (Simplified Voice Message) Intercept Group Name Specifies the name of the trunk group for programming reference.
2.9 [3] Group 200 PC Programming Manual Default Not stored. Value Range Max. 20 characters Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.15.1 [9-1] CO Line Settings Feature Manual References None Intercept Destination—Day, Lunch, Break, Night Specifies the intercept routing destination of unanswered calls (whose original destination is the floating extension number of a PS Ring Group, VM Group, External Pager [TAFAS], or DISA) in each time mode. Default Not stored. Value Range Max. 32 digits (consisting of 0–9, *, #, [ ] [Secret], and P [Pause]) Maintenance Console Location 2.9.1 [3-1-1] Trunk Group—TRG Settings Programming Manual References 2.8.5 [2-4] Week Table 2.15.1 [9-1] CO Line Settings Feature Manual References 1.9.9 Intercept Routing Host PBX Access Code Group Name Specifies the name of the trunk group for programming reference. Default Not stored.