Panasonic Kx Taw848 PC Cprogramming Manual

							2.8 [2] System
PC Programming Manual 181
Confirmation Tone—Tone 3-1 : Start Talking after making call
Enables the PBX to send Confirmation Tone 3-1. Confirmation Tone 3-1 is heard from an extension 
when, for example, it pages another extension.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.14 Confirmation Tone
Confirmation Tone—Tone 3-2 : Start Talking after answering call
Enables the PBX to send Confirmation Tone 3-2. Confirmation Tone 3-2 is heard from an extension 
when answering a call by, for example, the Call Pickup feature.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.14 Confirmation Tone
Confirmation Tone—Tone 4-1 : Start Conference
Enables the PBX to send Confirmation Tone 4-1. Confirmation Tone 4-1 is heard from an extension 
when a new party joins a conference call.
Default
Enable 
						

							2.8 [2] System
182 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.13 Conference
1.3.14 Confirmation Tone
Confirmation Tone—Tone 4-2 : Finish Conference
Enables the PBX to send Confirmation Tone 4-2. Confirmation Tone 4-2 is heard from an extension 
when a party leaves a conference call.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.13 Conference
1.3.14 Confirmation Tone
Confirmation Tone—Tone 5 : Hold
Enables the PBX to send Confirmation Tone 5. Confirmation Tone 5 is heard from an extension when 
it holds a call.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options 
						

							2.8 [2] System
PC Programming Manual 183
Programming Manual References
None
Feature Manual References
1.3.14 Confirmation Tone
Dial Tone—Distinctive Dial Tone
Enables the PBX to send dial tones at different frequencies depending on the setting of the extension.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.4.3 Dial Tone
Dial Tone—Dial Tone for Extension
Selects the dial tone the PBX sends to extensions to inform about the features activated on them.
Default
Ty p e  A
Value Range
Type A, Type B
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.4.3 Dial Tone
Dial Tone—Dial Tone for ARS
Selects the dial tone the PBX (instead of the network) sends to the caller when a call is made using 
the ARS feature. 
						

							2.8 [2] System
184 PC Programming Manual
Default
Ty p e  A
Value Range
Type A, Type B
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
2.14.1 [8-1] System Settings
Feature Manual References
1.1.3 ARS (Automatic Route Selection)
1.4.3 Dial Tone
Echo Cancel—Conference
Enables the use of the ECHO card for conference calls.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.13 Conference
Echo Cancel—CO-to-CO
Enables the use of the ECHO card for CO-to-CO line call line calls.
Default
Enable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options 
						

							2.8 [2] System
PC Programming Manual 185
Programming Manual References
None
Feature Manual References
None
Echo Cancel—Extension to Analog Line
Enables the use of the ECHO card for extension-to-analog CO line calls.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
None
Option 4
DSS Key—DSS Key mode for Incoming Call
Enables the use of a DSS button to pick up an incoming call to another extension or an ICD group.
Default
OFF
Value Range
ON or Flash, OFF
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.6 Call Pickup
1.10.1 LED Indication 
						

							2.8 [2] System
186 PC Programming Manual
DSS Key—Call Pick-up by DSS key for Direct Incoming Call
Specifies whether a DSS button will light up or flash when a call rings at the specified extension. To 
enable this setting, 
DSS Key—DSS Key mode for Incoming Call on this screen must be set to ON 
or Flash.
Default
Enable
Value Range
Disable: The DSS button will light up when a call arrives, but pressing it will not pick up the call. 
Enable: The DSS button will flash when a call arrives, and pressing it will pick up the call.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.6 Call Pickup
DSS Key—Call Pick-up by DSS key for ICD Group Call
Specifies whether a DSS button will light up or flash when a call rings at the specified incoming call 
distribution group.
 
To enable this setting, DSS Key—DSS Key mode for Incoming Call on this screen must be set to 
ON or Flash.
Default
Disable
Value Range
Disable: The DSS button will light up when a call arrives, but pressing it will not pick up the call. 
Enable: The DSS button will flash when a call arrives, and pressing it will pick up the call.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.6 Call Pickup
DSS Key—Automatic Transfer for Extension Call
Specifies whether pressing a DSS button during an extension-to-extension call disconnects the 
current call or places the call on consultation hold. 
						

							2.8 [2] System
PC Programming Manual 187
Default
Disable
Value Range
Disable: The PBX disconnects the current call, and calls the extension assigned to the DSS button. 
Enable: The PBX places the current call on consultation hold.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.8 Call Transfer
Transfer—Transfer to Busy Extension without BSS Operation
Enables a transferred call to be queued when the transfer destination is busy.
Default
Disable
Value Range
Disable: The call is not transferred. (If the transfer destination has enabled the call waiting notification 
feature, it is possible to inform the destination about the call transfer.)
 
Enable: The transferred call is queued for the time period specified in Recall—Transfer Recall in 
2.8.4 [2-3] Timers & Counters.
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
2.8.4 [2-3] Timers & Counters—Recall—Transfer Recall
Feature Manual References
1.3.8 Call Transfer
1.9.5 ICD Group Features—Queuing
Transfer—Automatic Answer for Transferred Call
Enables transferred calls (including direct extension calls) to be automatically answered, when using 
the Hands-free Answerback feature.
Default
Disable 
						

							2.8 [2] System
188 PC Programming Manual
Value Range
Disable, Enable
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.8.1 Hands-free Answerback
Option 5
SLT—SLT Hold Mode
Selects how to hold a line and transfer a call with an SLT. For details of each mode, see 1.3.2 Call 
Hold in the Feature Manual.
Default
Mode 2
Value Range
Mode 1, Mode 2, Mode 3, Mode 4
Maintenance Console Location
2.8.17 [2-9] System Options
Programming Manual References
None
Feature Manual References
1.3.2 Call Hold
2.8.18 [2-10] Extension CID Settings
Various settings for extension Caller ID can be programmed.
Extension Caller ID Resource-1, 2
Specifies a group of 4 SLT ports that can transfer Caller ID information to connected SLTs. 
When the port to which an extension is connected has this feature activated, there will be a shor t 
delay before the extension rings for incoming calls.
Default
Disable 
						

							2.8 [2] System
PC Programming Manual 189
Value Range
Disable: No port 
Slot 01:HLC4: Initially installed 4 Hybrid ports 
Slot nn:SLC8 1-4: Ports 1 to 4 of the SLC8 card (nn=slot number) 
Slot nn:SLC8 5-8: Ports 5 to 8 of the SLC8 card (nn=slot number)
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
2.10.1 [4-1-1] Wired Extension—Extension Settings—Option 7—Extension Caller ID Sending
Feature Manual References
1.3.1 Caller ID
Extension Caller ID Modulation Type
Specifies the modulation frequency to be used when sending Caller ID information to an SLT.
Default
Bell202(Bellcore)
Value Range
V.23(ETSI), Bell202(Bellcore)
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Channel Seizure Signal bits
Specifies the number of seizure bits to send when sending Caller ID information to an SLT.
Default
300 bits
Value Range
10 × n (n=3–40) bits
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings 
						

							2.8 [2] System
190 PC Programming Manual
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Mark Signal bits
Specifies the number of mark bits to send when sending Caller ID information to an SLT.
Default
180 bits
Value Range
10 × n (n=3–40) bits
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID
Channel Seizure Wait Time
Specifies the length of time that the PBX waits before starting to send the seizure signal following the 
first ring when sending Caller ID information to an SLT.
Default
512 ms
Value Range
64 × n (n=5–35) ms
Maintenance Console Location
2.8.18 [2-10] Extension CID Settings
Programming Manual References
None
Feature Manual References
1.3.1 Caller ID