Panasonic Kx Taw848 PC Cprogramming Manual

							2.10 [4] Extension
PC Programming Manual 261
Pickup Dial Number
Specifies the number to be dialed automatically after going off-hook when the Hot Line feature is 
active.
Default
Not stored.
Value Range
Max. 32 digits (consisting of 0–9, *, #, T [Transfer], [ ] [Secret], P [Pause], and F [Flash])
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.8.6 Hot Line
Data Mode
Sets or cancels the protection against tones or interruptions from other extensions during 
communication.
Default
Off
Value Range
Off, On
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.4.1 Data Line Security
Option 3
Slot
Indicates the slot position of each extension card (reference only).
Default
Current slot number 
						

							2.10 [4] Extension
262 PC Programming Manual
Value Range
Slot number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the port is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101 
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.) 
						

							2.10 [4] Extension
PC Programming Manual 263
Value Range
Max. 4 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None
Extension Name
Specifies the name of the extension.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Call Pickup Deny
Specifies whether calls can be picked up by other extensions.
Default
Disable
Value Range
Disable: Allows other extension users to pick up calls to your extension 
Enable: Prevents other extension users from picking up calls to your extension
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None 
						

							2.10 [4] Extension
264 PC Programming Manual
Feature Manual References
1.3.6 Call Pickup
Executive Override Deny
Specifies whether calls can be interrupted by other extensions.
Default
Disable
Value Range
Disable: Allows other extension users to interrupt an existing call 
Enable: Prevents other extension users from interrupting an existing call
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.5.3 Executive Busy Override
Absent Message
Specifies the Personal Absent Message which, unlike the System Absent Message, can be 
customized for each extension.
Default
Not stored.
Value Range
Max. 16 characters
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.1.1 Absent Message
Option 4
Slot
Indicates the slot position of each extension card (reference only). 
						

							2.10 [4] Extension
PC Programming Manual 265
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the por t number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the por t is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits. 
						

							2.10 [4] Extension
266 PC Programming Manual
Default
Starting at 101 
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.)
Value Range
Max. 4 digits (consisting of 0–9)
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.5 [1-1] Slot—Extension Port—Port Command
Feature Manual References
None
Extension Name
Specifies the name of the extension.
Default
Not stored.
Value Range
Max. 20 characters
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Outgoing Preferred Line
Selects the line to be seized after going off-hook to make a call.
Default
ICM
Value Range
No Line: No line is seized. 
Idle: An idle CO line is seized automatically from the programmed trunk groups. 
ICM: An extension line is seized.  
						

							2.10 [4] Extension
PC Programming Manual 267
F-1–F-12: A CO line programmed for a flexible CO button (F-1–F-12) is seized. A flexible CO button 
customized as a Single-CO, Group-CO, Loop-CO, or ICD Group button must be selected.
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.10.4 [4-1-4] Wired Extension—Flexible Button
Feature Manual References
1.10.3 Line Preference—Outgoing
Incoming Preferred Line
Selects the line on which an incoming call is answered after going off-hook.
Default
Ringing Line
Value Range
No Line: No line is selected. Select a line by pressing the desired Line Access button to answer a call. 
Ringing Line: The longest ringing call is selected. 
F-1–F-12: The call arriving at a flexible CO button (F-1–F-12) is selected. A flexible CO button 
customized as a Single-CO, Group-CO, Loop-CO, or ICD Group button must be selected.
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.10.4 [4-1-4] Wired Extension—Flexible Button
Feature Manual References
1.10.2 Line Preference—Incoming
Intercom Call by Voice
Selects the method of receiving intercom calls. When Deny Voice Call is selected, the extension will 
always ring when receiving calls, regardless of how the caller wants to make the call.
Default
Tone Call
Value Range
Tone Call, Voice Call, Deny Voice Call
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings 
						

							2.10 [4] Extension
268 PC Programming Manual
Programming Manual References
None
Feature Manual References
1.9.11 Intercom Call
Call Waiting Tone Type
Selects the type of Call Waiting tone sent to the busy extension.
Default
CW Tone 1
Value Range
CW Tone 1, CW Tone 2
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.3.9 Call Waiting Tone
LCS Recording Mode
Specifies whether to continue or stop recording the message in the extensions mailbox when the 
extension user answers a call that was being monitored.
Default
Stop Record
Value Range
Stop Record, Keep Record
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.19.4 Voice Mail DPT (Digital) Integration
LCS Answer Mode
Specifies whether the extensions mailbox is monitored in Hands-free or Private mode. 
						

							2.10 [4] Extension
PC Programming Manual 269
Default
Hands free
Value Range
Hands free: Monitor through the built-in speaker 
Private: Monitor through the handset or the built-in speaker after hearing a warning tone
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.8.2 Hands-free Operation
1.19.4 Voice Mail DPT (Digital) Integration
Display Language
Selects the display language of the extension telephone.
Default
Language 1
Value Range
Language1–Language5
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
1.4.7 Display Information
Option 5
Slot
Indicates the slot position of each extension card (reference only).
Default
Current slot number
Value Range
Slot number 
						

							2.10 [4] Extension
270 PC Programming Manual
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.10.1 [4-1-1] Wired Extension—Extension Settings
Programming Manual References
2.7.4 [1-1] Slot—Extension Port
Feature Manual References
None
Extension Number
Specifies the extension number of the extension.
To change the extension number of a wired extension, follow the steps below:
1.Type the new extension number, then click Apply.
2.Set the status of the extension port to OUS, then INS.
When changing the extension number, make sure that the extension port is not in use. If the extension 
number is changed while the port is in use, the new extension number will not come into effect.
Note that extensions that will have a mailbox using a VM in DPT integration must have extension 
numbers of 2–4 digits.
Default
Starting at 101 
(For port 01 of the first extension card that is installed. Extension numbers are preset for subsequent 
extensions by adding one to the previous extension number.)
Value Range
Max. 4 digits (consisting of 0–9)