Canon Imageprograf Ipf8300 User Guide

							•Press  Back  to  access  a  higher  menu  in  the  menu  list,  and  press  OK to  access  a  lower  one.  If  not  all  menu  items  are
displayed, hold down  ▲ or  ▼ to scroll through higher and lower menu items. Items you select are highlighted.
The scroll bar at right indicates the current position in the overall menu.
• Lower menus are available if 
 is displayed at left next to the second and subsequent rows. To access the lower me-
nus, select the menu and press the  OK button.
Specifying menu items
Menu items can be set as follows.
1. Press  ▲ or  ▼ to select the desired setting, and then press the  OK button.
After two seconds, the display reverts to the upper level menu.
Note•If  a  confirmation  message  is  displayed  regarding  the  setting  you  entered,  press  the  OK button.  The
setting is applied, and the printer is now in  Standby.
Printer Parts 
>
 Control Panel 
>iPF8300Menu Operations9903
 
						

							Specifying numerical valuesFollow these steps to enter numbers. In this example, network settings items are entered.
1. Press the  ◀ or  ▶ button to move to the next field for input.
2. Press the  ▲ or  ▼ button to enter the value.
Note•Hold down  ▲ or  ▼ to increase or decrease the value continuously.
3. Repeat steps 1 and 2 to complete the settings, and then press the  OK button.
Note•If  a  confirmation  message  is  displayed  regarding  the  setting  you  entered,  press  the  OK button.  The
setting is applied, and the printer is now in  Standby.
Executing menu commands
Menu commands can be executed as follows.
1. Press  ▲ or  ▼ to select the action to execute, and then press the  OK button.
The menu command is now executed.
Menu Structure
The menu structure is organized by tabs, as follows. Values at right indicated by an asterisk are the defaults. •Paper Menu 
→P.904
• Ink Menu 
→P.906
• Job Menu 
→P.906
• Set./Adj. Menu 
→P.907
For instructions on menu operations,  see "Menu Operations ."
→P.902
For details on menu items,  see "Menu Settings ."
→P.912
Paper Menu
First LevelSecond LevelThird LevelFourth LevelLoad PaperRoll Paper
Cut SheetEject PaperChg. Paper Type
( *1
→P.906 )
Roll Paper(The type of paper is displayed here.) ( *1→P.906)
Printer Parts 
>
 Control Panel 
>Menu StructureiPF83009904
 
						

							First LevelSecond LevelThird LevelFourth LevelChg. Paper Type
( *1
→P.906 )
Cut Sheet(The type of paper is displayed here.) ( *1→P.906)Chg. Paper SizeSheet Size
( *2
→P.906 )
(The size of paper is displayed here.) ( *3→P.906)Roll Length  (*4→P.906 )
Roll Width  (*2
→P.906 )
ManageRemainRollOff *
OnPaper Details(The type of paper is dis-
played here.)
( *1
→P.906 )
Head HeightAutomatic  *
Highest
High
Standard
Low
Lowest
Super LowSkew Check Lv.Standard  *
Loose
OffCutting ModeAutomatic
Eject
ManualCut SpeedFast
Standard
SlowTrim Edge FirstAutomatic
Off
OnCutDustReduct.Off
OnVacuumStrngthAutomatic  *
Strongest
Strong
Standard
Weak
WeakestScan Wait TimeOff
1 sec.
3 sec.
5 sec.
7 sec.
9 sec.Roll DryingTimeOff
30 sec.
1 min.
3 min.
5 min.
10 min.
30 min.
60 min.NearEnd RollMrgn5mm
Printer Parts 
>
 Control Panel 
>iPF8300Menu Structure9905
 
						

							First LevelSecond LevelThird LevelFourth LevelPaper Details(The type of paper is dis-
played here.)
( *1
→P.906 )
NearEnd RollMrgn20mmNearEnd Sht Mrgn5mm
20mmBordless MarginAutomatic
FixedWidth DetectionOff
On  *Return DefaultsPaper DetailsKeep Paper TypeOff  *
On
*1:   For information on the types of paper the printer supports, refer to the Paper Reference Guide.   (See "Types of
Paper .")
→P.768  Types of paper in the printer driver and related software (as well as on the Control Panel )
are updated when you install the printer driver from the User Software CD-ROM or if you update paper informa-
tion with the Media Configuration Tool. (See the  Media Configuration Tool
→P.440 or Media Configuration
Tool
→P.671 .)
*2:   Available only if  Width Detection is Off .
*3:   For information on the sizes of paper the printer supports,  see "Paper Sizes ."
→P.771
*4:   Available only if  ManageRemainRoll is On .
Ink Menu
First LevelRep. Ink TankHead Cleaning A
Job Menu
First LevelSecond LevelThird LevelFourth LevelFifth LevelPrint JobJob List(Choose a print job.)Delete
Preempt Jobs  (*1
→P.907 )
Stored JobMailbox List(Enter a password if
one has been set.)Job ListPrint
DeletePrint Job ListJob Log(Choose from infor-
mation about the lat-
est three print jobs.)Document Name
User Name
Page CountJob StatusOK
CANCELEDPrint Start Timeyyyy/mm/dd hh:mm:ssPrint End Timeyyyy/mm/dd hh:mm:ssPrint Timexxxsec.Print Sizexxxxxxxxsq.mmMedia Type
Printer Parts 
>
 Control Panel 
>Menu StructureiPF83009906
 
						

							First LevelSecond LevelThird LevelFourth LevelFifth LevelJob Log(Choose from infor-
mation about the lat-
est three print jobs.)InterfaceUSB
Network
HDDInk Consumed(The total amount of
ink consumed and
ink colors are dis-
played here.)xxx.xxx mlPrint settings
Head Height
Temp./Humidity
Adjustment req.Print Job LogPause PrintOff  *
OnHDD InformationTotal capacity
Box free space
*1:   If a pending job is selected,  Print Anyway is displayed.
Set./Adj. Menu
First LevelSecond Lev-
elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelTest PrintNozzle Check
Status Print
Interface Print
Paper Details
Print Job Log
Menu MapAdjust
PrinterHead Posi.
Adj.Auto(Standard)
Auto(Advanced)
Auto(Expansion)  (*1
→P.912 )
Manual  (*1
→P.912 )
Feed Priori-
tyAdj. Priority
( *2
→P.912 )
Automatic  *
Print Quality
Print LengthAdj. Quality
( *2
→P.912 ),
( *3
→P.912 )
Auto(GenuinePpr)
Auto(OtherPaper)
ManualAdjust
Length
( *2
→P.912 ),
( *4
→P.912 )
Adjustment-
PrintA:High
B:Standard/DraftChange Set-
tingsA:High
B:Standard/DraftCalibrationAuto AdjustCalibration
LogDate
Paper Type
Printer Parts 
>
 Control Panel 
>iPF8300Menu Structure9907
 
						

							First LevelSecond Lev-elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelAdjust
PrinterCalibrationUse Adj.
ValueDisabled
Enabled  *Return DefaultsMaintenanceHead Clean-
ingHead Cleaning A
Head Cleaning BNozzle CheckReplace
P.headPrinthead L
Printhead R
L & R PrintheadsRepl. maint cartHead InfoPrinthead L
Printhead RRepl. S. Cleaner
Change CutterInterface
SetupEOP Timer
( *5
→P.912 )
10 sec.
30 sec.
1 min.
2 min.
5 min.
10 min.  *
30 min.
60 min.TCP/IP
( *5
→P.912 )
IPv4IPv4 ModeAutomatic
Manual  *Protocol
( *6
→P.912 )
DHCPOn
Off  *BOOTPOn
Off  *RARPOn
Off  *IPv4 Set-
tings
( *7
→P.912 )
IP Addressxxx.xxx.xxx.xxxSubnet
Maskxxx.xxx.xxx.xxxDefault G/Wxxx.xxx.xxx.xxxDNS Set-
tings
( *7
→P.912 )
DNS Dync
updateOn
Off  *Pri. DNS SrvAddr
Sec. DNS SrvAddr
DNS Host Name
DNS Domain NameIPv6IPv6 Sup-
portOn
Off  *IPv6 Stles-
sAddrs
( *8
→P.912 )
On *
Off
Printer Parts 
>
 Control Panel 
>Menu StructureiPF83009908
 
						

							First LevelSecond Lev-elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelInterface
SetupTCP/IP
( *5
→P.912 )
IPv6DHCPv6
( *8
→P.912 )
On
Off  *DNS Set-
tings
( *7
→P.912 ),
( *8
→P.912 )
DNS Dync
updateStatefull
AddrOn
Off  *Stateless
AddrOn
Off  *Pri. DNS SrvAddr
Sec. DNS SrvAddr
DNS Host Name
DNS Domain NameNetWare
( *5
→P.912 )
NetWareOn
Off  *Frame Type
( *9
→P.912 )
Auto Detect
Ethernet 2
Ethernet 802.2  *
Ethernet 802.3
Ethernet SNAPPrint Service
( *9
→P.912 )
BinderyPServer
RPrinter
NDSPServer  *
NPrinterAppleTalk
( *5
→P.912 )
On
Off  *Ethernet
Driver
( *5
→P.912 )
Auto DetectOn *
OffComm.Mode
( *10
→P.912 )
Half Duplex  *
Full DuplexEthernet
Type
( *10
→P.912 )
10 Base-T  *
100 Base-TX
1000 Base-TSpanning
TreeNot Use  *
UseMAC Ad-
dressxxxxxxxxxxxxInterface Print  (*5→P.912 )Return Defaults  (*5→P.912 )System Set-
upSleep Timer5 min.  *
10 min.
15 min.
20 min.
30 min.
40 min.
50 min.
60 min.
Printer Parts 
>
 Control Panel 
>iPF8300Menu Structure9909
 
						

							First LevelSecond Lev-elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelSystem Set-
upSleep Timer240 min.BuzzerOff
On  *Contrast
Adj.-4,-3,-2,-1,0*,+1,+2,+3,+4Date & Time
( *5
→P.912 )
Dateyyyy/mm/dd  (*11→P.912 )Timehh:mmDate Format
( *5
→P.912 )
yyyy/mm/dd  *
dd/mm/yyyy
mm/dd/yyyyLanguage*Time Zone
( *5
→P.912 )
0:London (GMT)
+1:Paris,Rome
+2:Athens,Cairo
+3:Moscow
+4:Eerevan,Baku
+5:Islamabad
+6:Dacca
+7:Bangkok
+8:Hong Kong
+9:Tokyo,Seoul
+10:Canberra
+11NewCaledonia
+12:Wellington
-12:Eniwetok
-11:Midway is.
-10Hawaii(AHST)
-9:Alaska(AKST)
-8:Oregon (PST)
-7:Arizona(MST)
-6:Texas (CST)
-5:NewYork(EST)
-4:Santiago
-3:Buenos Aires
-2:
-1:Cape VerdeLength Unitmeter  *
feet/inch
Printer Parts 
>
 Control Panel 
>Menu StructureiPF83009910
 
						

							First LevelSecond Lev-elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelSystem Set-
upDetect Mis-
matchPause
Warning
None  *
Hold JobPaper Size
BasisSht Selection
1ISO A3+  *
13"x19"(Super B)Sht Selection
2ISO B1  *
28"x40" (ANSI F)Keep Paper
SizeOff  *
OnRep.P.head
PrintOff
On  *Nozzle
CheckFrequencyStandard  *
1 pageWarningOff  *
OnCarriageS-
canWdthAutomatic  *
FixedUse Remo-
teUI
( *5
→P.912 )
On *
OffReset PaprSetngs  (*5→P.912 )Erase HDD
DataHigh Speed  (*5→P.912 )
Secure High Spd.  (*5
→P.912 )
Secure  (*5
→P.912 )
Output
MethodPrint  *
Print (Auto Del)
Save: Box XXPrint After
RecvOff  *
OnCommon
Box Set.
( *5
→P.912 )
Print
Print (Auto Del)  *Show Job
Log
( *5
→P.912 )
Off
On  *Take-up
Reel
( *12
→P.912 )
Use Take-up
ReelDisable  *
EnableAuto Feed  (*13→P.912 )Skip Take-
Up Err
( *14
→P.912 )
Off *
On
Printer Parts 
>
 Control Panel 
>iPF8300Menu Structure9911
 
						

							First LevelSecond Lev-elThird LevelFourth LevelFifth LevelSixth LevelSeventh LevelPrep.Move-
PrinterLevel 1  *
Level 2
Level 3Admin.
Menu
( *5
→P.912 )
Change Password  (*7→P.912 )
Init.Admin.Pswd  (*7
→P.912 )
Printer InfoPaper Info
Ink InfoHead InfoPrinthead L
Printhead RSystem Info
Error Log
Other Counter
*1:   Available after you have used  Auto(Advanced) in Head Posi. Adj.  once.
*2:   Displayed if a sheet is loaded in the printer.
*3:   Available if  Adj. Priority is Automatic  or Print Quality .
*4:   Available if  Adj. Priority is Automatic  or Print Length .
*5:   Viewing and configuration is possible for administrators, and only viewing for other users. *6:   Not displayed if  IPv4 Mode is Manual .
*7:   Viewing and configuration is possible for administrators only.
*8:   Not displayed if  IPv6 Support is Off .
*9:   Not displayed if  NetWare is Off .
*10:   Not displayed if  Auto Detect is On .
*11:   Follows the setting in  Date Format.
*12:   Displayed only when the Media Take-up Unit is attached. *13:   Available if: (a)  Use Take-up Reel is Enable , (b) roll paper is loaded, and (c) you have not executed  Auto
Feed  for the loaded roll.
*14:   Available when  Use Take-up Reel is Enable .
Menu Settings
Menu items are as follows.
For instructions on selecting menu items,  see "Menu Operations ."
→P.902
For details on menu levels and values,  see "Menu Structure ."
→P.904
Paper Menu
Setting ItemDescription, InstructionsLoad PaperSelect either sheets or rolls and load the paper.Eject PaperChoose this item before removing loaded paper.Chg. Paper Type  (*1→P.914 )Change the type of paper loaded.   (See "Changing the Type
of Paper .")
→P.784
Chg. Paper SizeChange the size of paper loaded.   (See "Specifying the Pa-
per Length .")
→P.785  (See " Paper Sizes .")→P.771Printer Parts 
>
 Control Panel 
>Menu SettingsiPF83009912