Canon Pixma Mp630 User Guide

							Advanced Guide > Printing Photographs Directly from a Compliant Device or a Wireless Communication Device > Printing
Photographs from a Wireless Communication Device > Setting the Page Size, Media Type, and Layout When Printing froma Mobile Phone
Setting the Page Size, Media Type, and Layout When Printing
from a Mobile Phone
When printing from a mobile phone through Infrared communication or Bluetooth communication, select
the page size, media type, layout, and borderless print setting on the Mobile phone print setting screen.
For details on how to print from a computer through Bluetooth communication, refer to About Bluetooth
Communication.
* The default is borderless printing on L size Photo Paper Plus Glossy II.
Displaying the Mobile phone print setting screen
This section describes how to display the Mobile phone print setting screen. For setting items,
see Mobile phone print setting.
1.Make sure that the machine is turned on.
2.Select  Settings on the HOME screen, then press the OK button.
3.Select  Device settings, then press the OK button.
4.Select Mobile phone print setting, then press the OK button.
The Mobile phone print setting screen is displayed. For the setting items, see Mobile phone
print setting.
Page top
Page 621 of 805 pages Setting the Page Size, Media Type, and Layout When Printing from a Mobil...
 
						

							Advanced Guide > Printing Photographs Directly from a Compliant Device or a Wireless Communication Device > Printing
Photographs from a Wireless Communication Device > Printing via Infrared Communication
Printing via Infrared Communication
You can print photos saved on your mobile phone via infrared communication.
When printing through infrared communication, also refer to your mobile phones instruction manual.
1.Make sure that the machine is turned on.
2.Load paper.
3.Set the print setting and layout.
Setting the Page Size, Media Type, and Layout When Printing from a Mobile Phone
4.Place the mobile phone so that its infrared port comes face to face to that of the
machine at a distance of less than approximately 8 inches / 20 cm.
Note
The effective angle of the IrDA Port (B) of the machine is about 10 degrees up, left, or right from
the central axis (A). The effective range of communication with the machine depends on the
mobile phone you are using. For details, refer to your mobile phones instruction manual.
(A) Effective angle: 10 degrees up, left, or right from the central axis
(B) IrDA Port of the machine
(C) Approximately 8 inches / 20 cm (Do not block with an object.)
(D) IrDA Port of the mobile phone
5.Select the photo to print and send the data to the machine using the infrared
communication function of the mobile phone.
Printing will start after receiving all data.
Note
Do not place any obstacle between the infrared ports of the machine and mobile phone, as it
will block data transmission.
During receiving data, be careful not to interrupt infrared communication with the machine. If it
is interrupted, send the data from the mobile phone again.
Depending on your device, the print quality may be degraded due to the restriction on the
infrared transfer capacity.
We recommend printing on sticker when the print quality on other types of paper is not fine.
Page 622 of 805 pages Printing via Infrared Communication
 
						

							Video files cannot be printed.
Depending on the size of a photo, it may take a while for this machine to start printing after
starting infrared communication.
About transmittable data
Due to security settings on the mobile phone, downloaded content or photos
downloaded from a URL attached to an E-mail cannot be printed.
Depending on your device, data saved on a memory card may not be printed.
Printed quality and orientation (portrait or landscape) are determined automatically
according to the shot photo size.
Depending on the photo size shot on the mobile phone, the edges of the image may be
cut off when performing borderless printing; the margin size may change when printing
with borders.
If the photo file is over 1.8 MB in size, it may not be possible to send the file.
Page top
Page 623 of 805 pages Printing via Infrared Communication
 
						

							Advanced Guide > Printing Photographs Directly from a Compliant Device or a Wireless Communication Device > Printing
Photographs from a Wireless Communication Device > Printing via Bluetooth Communication
Printing via Bluetooth Communication
This section describes the procedure to print photos through Bluetooth communication from a mobile
phone with the optional Bluetooth Unit BU-30.
When printing from a mobile phone through Bluetooth communication, refer also to your products
instruction manual.
For the procedure to print through Bluetooth communication from the computer, refer to About Bluetooth
Communication.
Note
Mobile phones supporting OPP (Object Push Profile) or BIP (Basic Image Profile) can print photos.
Depending on your mobile phone, you may not perform printing even if your mobile phone supports
the profiles above. For information on the profiles your mobile phone supports, refer to your
products instruction manual.
Printing through Bluetooth Communication
1.Make sure that the machine is turned on.
2.Load paper on the Rear Tray.
3.Attach the optional Bluetooth Unit BU-30.
Insert the Bluetooth Unit BU-30 to the Direct Print Port.
4.Set the page size and layout.
Setting the Page Size, Media Type, and Layout When Printing from a Mobile Phone
5.Start printing from a mobile phone.
For the device name, select the default value Canon XXX-1 (where XXX
is your machines name).
If you are required to input a passkey, input the default value 0000.
You can change the device name of the machine, passkey, and so on from the
Page 624 of 805 pages Printing via Bluetooth Communication
 
						

							Bluetooth settings screen.
Changing the Bluetooth Settings
Note
Communication is possible in a range of up to about 33 ft. / 10 m depending on
the conditions below. Printing speed may vary depending on the following
conditions:
Presence of obstacles between the communication equipment, and radio
conditions.
Presence of magnetic fields, static electricity, or electromagnetic interference.
Receiver sensitivity and antenna performance of the communication equipment.
For the transmittable data, see About transmittable data.
Page top
Page 625 of 805 pages Printing via Bluetooth Communication
 
						

							Advanced Guide > Printing Photographs Directly from a Compliant Device or a Wireless Communication Device > Printing
Photographs from a Wireless Communication Device > Printing via Bluetooth Communication > Changing the Bluetooth
Settings
Changing the Bluetooth Settings
As preparation for printing through Bluetooth communication, you can change the settings such as the
device name and passkey from the Bluetooth settings screen.
This section describes how to display the Bluetooth settings screen. For each setting item, see 
Bluetooth settings.
1.Make sure that the machine is turned on.
2.Attach the optional Bluetooth Unit BU-30.
Insert the Bluetooth Unit BU-30 to the Direct Print Port.
3.Select  Settings on the HOME screen, then press the OK button.
4.Select  Device settings, then press the OK button.
5.Select Bluetooth settings, then press the OK button.
The Bluetooth settings screen is displayed.
Page top
Page 626 of 805 pages Changing the Bluetooth Settings
 
						

							Advanced Guide > Maintenance
Maintenance
Cleaning Your Machine
Aligning the Print Head Manually
Performing Maintenance from a Computer
Page top
Page 627 of 805 pages Maintenance
 
						

							Advanced Guide > Maintenance
 > Cleaning Your Machine
Cleaning Your Machine
Cleaning
Cleaning the Exterior of the Machine
Cleaning the Platen Glass and Document Cover
Cleaning the Inside of the Machine (Bottom Plate Cleaning)
Cleaning the Protrusions Inside the Machine
Page top
Page 628 of 805 pages Cleaning Your Machine
 
						

							Advanced Guide > Maintenance > Cleaning Your Machine > Cleaning
Cleaning
This section describes the cleaning procedure that is needed to maintain your machine.
Caution
Do not use tissue paper, paper towels, rough-textured cloth, or similar materials for cleaning so as
not to scratch the surface. Paper tissue powders or fine threads may remain inside the machine
and cause problems such as Print Head blockage and poor printing results. Be sure to use a soft
cloth.
Never use volatile liquids such as thinners, benzene, acetone, or any other chemical cleaner to
clean the machine, as this may cause a malfunction or damage the machines surface.
Cleaning the Exterior of the Machine
Cleaning the Platen Glass and Document Cover
Cleaning the Inside of the Machine (Bottom Plate Cleaning)
Cleaning the Protrusions Inside the Machine
Page top
Page 629 of 805 pages Cleaning
 
						

							Advanced Guide > Maintenance > Cleaning Your Machine > Cleaning the Exterior of the Machine
Cleaning the Exterior of the Machine
Be sure to use a soft cloth such as eyeglasses cleaning cloth and wipe off dirt on the surface with it
gently. Smooth out wrinkles on the cloth if necessary before cleaning.
Caution
Be sure to turn off the power and disconnect the power plug before cleaning the machine.
Do not use tissue paper, paper towels, rough-textured cloth, or similar materials, as this may
scratch the surface.
Page top
Page 630 of 805 pages Cleaning the Exterior of the Machine