Canon Pixma Mp630 User Guide

							registered will be deleted from Printing Profiles.
Registered print settings cannot be saved and preserved. In this case, register the print settings
again. 
Using registered print settings 
1.Select the print settings to be used 
Select a printing profile in the Printing Profiles list on the Profiles tab.
The parameters and settings of the profile are displayed in the Details box. 
2.Retrieve from Profiles 
Click Retrieve from Profiles.
Click OK when a message appears.
Settings of the selected profile are applied to the Main, Page Setup, and Effects tabs. 
Note 
If you want to revert a profile to the default settings, select Default Settings in the Printing Profiles list
and click Retrieve from Profiles. Click OK on the confirmation message window. The settings which
were made on the Main, Page Setup, and Effects tabs are reverted to the default settings. 
Deleting unnecessary printing profile 
1.Select the printing profile to be deleted 
Select the printing profile you want to delete from the Printing Profiles list on the Profiles tab. 
2.Delete the printing profile 
Click Delete. When the confirmation message appears, click OK.
The selected printing profile is deleted from the Printing Profiles list. 
Note 
Current Settings and Default Settings cannot be deleted. 
Page top
Page 691 of 805 pages Saving a Changed Printing Profile
 
						

							Advanced Guide > Changing the Printer Settings > Changing Printer Settings from Your Computer > Setting the Paper
Source for Plain Paper 
Setting the Paper Source for Plain Paper 
When you select Automatically Select from Paper Source, you can use the printer driver to select the
paper source for plain paper. 
The procedure for setting the paper source is as follows: 
 Paper Source Setting for Plain Paper 
1.Open the printer driver setup window
2.Click Paper Source Setting for Plain Paper on the Maintenance tab 
The Paper Source Setting for Plain Paper dialog box opens. 
3.Transmit the settings 
Select the paper source for plain paper, and then click the Send button. 
The selected settings are enabled hereafter. 
Important 
The descriptions in the machine manual assume that the plain paper is supplied from the
cassette. If you change the paper source setting, replace all instances of cassette with the new
paper source. 
Page top
Page 692 of 805 pages Setting the Paper Source for Plain Paper
 
						

							Advanced Guide > Changing the Printer Settings > Changing Printer Settings from Your Computer > Managing the
Machine Power 
Managing the Machine Power 
This function allows you to manage the machine power from the printer driver. 
The procedure for managing the printer power is as follows: 
 Power Off 
The Power Off function turns off the machine. If you use this function, you will not be able to turn the
machine on from the printer driver. 
1.Open the printer driver setup window
2.Execute power off 
Click Power Off on the Maintenance tab. When the confirmation message appears, click OK. 
The machine power switches off, and the Maintenance tab is displayed again. 
Page top
Page 693 of 805 pages Managing the Machine Power
 
						

							Advanced Guide > Changing the Printer Settings > Changing Printer Settings from Your Computer > Reducing the
Machine Noise 
Reducing the Machine Noise 
This function allows you to reduce the operating noise of the machine. Select if you wish to reduce the
operating noise of the printer at night, etc.
Using this function may lower the print speed. 
The procedure for changing the quiet mode settings is as follows: 
 Quiet Mode 
1.Open the printer driver setup window
2.Click Quiet Mode on the Maintenance tab 
The Quiet Mode dialog box opens. 
3.Set the silent function 
If necessary, specify one of the following items: 
Do not use quiet mode 
The operating noise of the machine is at normal volume. 
Always use quiet mode 
Select this option when you wish to reduce the operating noise of the machine. 
Use quiet mode within specified time 
The operating noise of the machine can be reduced during a specified period of time.
Set the Start time and End time when you wish the quiet mode to be activated. 
Important 
The time specified in Start time and in End time must be different. 
4.Transmit the settings 
Make sure that the machine is on and click Send.
Click OK when the confirmation message appears. 
The selected settings are enabled hereafter. 
Note 
The effects of the quiet mode may be less depending on the paper source and the print quality
settings. 
Page top
Page 694 of 805 pages Reducing the Machine Noise
 
						

							Advanced Guide > Changing the Printer Settings > Changing Printer Settings from Your Computer > Changing the
Machine Operation Mode 
Changing the Machine Operation Mode 
This function allows you to switch between various modes of machine operation. 
The procedure for changing the printer settings is as follows: 
 Custom Settings 
1.Open the printer driver setup window
2.Make sure that the machine is on, and then click Custom Settings on the
Maintenance tab 
The Custom Settings dialog box opens. 
Note 
If the machine is off or bi-directional communication is disabled, a message may appear
because the computer cannot collect the machine status.
If this happens, click OK to display the most recent settings specified on your computer. 
3.If necessary, complete the following settings: 
Prevent paper abrasion 
The printer can increase the gap between the print head and the paper during high-density printing
to prevent paper abrasion.
Check this check box to use this function. 
Align heads manually 
The Print Head Alignment function on the Maintenance tab is normally set to automatic head
alignment, but you can change it to manual head alignment. If the printing results are unsatisfactory
even after you execute automatic head alignment, see Manual Print Head Alignment, and execute
manual head alignment.
Check this check box to perform the manual head alignment. 
Ink Drying Wait Time 
You can set the length of the machine rest time until printing of the next page begins. Moving the
slider to the right increases the pause time and moving the slider to the left decreases the time.
If the paper gets stained because the next page is ejected before the ink on the printed page dries,
increase the ink drying wait time.
Reducing the ink drying wait time speeds up printing. 
4.Transmit the settings 
Click Send. When the confirmation message appears, click OK. 
The machine runs in the changed mode hereafter. 
Page top
Page 695 of 805 pages Changing the Machine Operation Mode
 
						

							Advanced Guide > Troubleshooting
Troubleshooting
If an Error Occurs
The Machine Can Not Be Powered On
An Error Message Is Displayed on the LCD
LCD Cannot Be Seen At All
An Unintended Language Is Displayed on the LCD
Cannot Install the MP Drivers
Cannot Connect to Computer Properly
Print Results Not Satisfactory
Printing Does Not Start
Copying/Printing Stops Before It Is Completed
Machine Moves But Ink Is Not Ejected
Printing Speed Not as Fast as Expected
Print Head Holder Does Not Move to the Position for Replacing
Paper Does Not Feed Properly
Paper Does Not Feed from the Paper Source Specified in the Printer Driver
Paper Jams
Message Appears on the Computer Screen
Cannot Print Properly with Automatic Duplex Printing
For Windows Users
Error Message Appears on a PictBridge Compliant Device
Cannot Print Properly from a Wireless Communication Device
Cannot Print Properly from a Photo Index Sheet
Cannot Remove a Memory Card
Problems with Scanning
Software Problems
MP Navigator EX Problems
FAQs
If You Cannot Resolve the Problem
Instructions for Use (Printer Driver)
General Notes (Scanner Driver)
Page top
Page 696 of 805 pages Troubleshooting
 
						

							Advanced Guide > Troubleshooting > If an Error Occurs
If an Error Occurs
When an error occurs in printing such as the printer is out of paper or paper is jammed, a
troubleshooting message is displayed automatically. Take the appropriate action described in the
message. The message may vary depending on the version of your operating system.
In Mac OS X v.10.5.x:
In Mac OS X v.10.4.x or Mac OS X v.10.3.9:
Page 697 of 805 pages If an Error Occurs
 
						

							Page top
Page 698 of 805 pages If an Error Occurs
 
						

							Advanced Guide > Troubleshooting > The Machine Cannot Be Powered On
The Machine Cannot Be Powered On
Check 1: Press the ON button.
Check 2: Make sure that the power plug is securely plugged into the
Power Cord Connector of the machine, then turn it back on.
Check 3: Unplug the machine from the power supply, then plug the
machine back in and turn the machine back on after leaving it for at
least 5 minutes.
If the problem is not resolved, contact your Canon service representative.
Page top
Page 699 of 805 pages The Machine Cannot Be Powered On
 
						

							Advanced Guide > Troubleshooting > An Error Message Is Displayed on the LCD
An Error Message Is Displayed on the LCD
If an error message is displayed on the LCD, take the corresponding action described below.
MessageAction
The following ink may have run out.
Replacing the ink tank is
recommended.
U041
If the lamp on the ink tank is flashing, ink may have run out.
Replacing the ink tank is recommended.
If printing is in progress and you want to continue printing,
press the OK button with the ink tank installed. Then printing
can continue. Replacing the ink tank is recommended after
the printing. The machine may be damaged if printing is
continued under the ink out condition.
Routine Maintenance
Note
If multiple ink lamps are flashing red, see Routine
Maintenance and check the status of each ink tank.
Print head is not installed.
Install the print head.
U051/
The type of print head is incorrect.
Install the correct print head.
U052
Follow the directions given in your setup sheet to install the
Print Head.
If the Print Head is already installed, remove the Print Head
once and then reinstall it.
If the error is not resolved, the Print Head may be damaged.
Contact your Canon service representative.
Some ink tanks are not installed in
place.
U072/
More than one ink tank of the following
color is installed.
U071
Some ink tanks are not installed in the correct position.
(The lamp on the ink tank flashes.)
More than one ink tanks of the same color are installed.
(The lamp on the ink tank flashes.)
Confirm that the ink tanks are installed in the appropriate
positions.
Routine Maintenance
The remaining level of the following ink
cannot be correctly detected.
Replace the ink tank.
U130
The remaining ink level cannot be correctly detected. (The
lamp on the ink tank flashes.)
Replace the ink tank and close the Scanning Unit (Cover).
Printing with an ink tank that was once empty may damage
the machine.
If you want to continue printing in this condition, you need to
release the function for detecting the remaining ink level.
Press and hold the Stop button for at least 5 seconds, and
then release it.
With this operation, releasing the function for detecting the
remaining ink level is memorized Please be advised that
Canon shall not be liable for any machine malfunction or
damage caused by refilled ink tanks.
Routine Maintenance
Note
If the function for detecting the remaining ink level is
disabled, the ink tank in gray is displayed on the LCD
when checking the current ink level.
Routine Maintenance
The following ink tank cannot be
recognized.
U043
U140
U150
The ink tank is not installed. Install the ink tank.
Routine Maintenance
The ink tank is not compatible with this machine. (The
lamp on the ink tank is off.)
Install an appropriate ink tank.
Routine Maintenance
An ink tank error has occurred. (The lamp on the ink tank
is off.)
Page 700 of 805 pages An Error Message Is Displayed on the LCD